You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
61 lines
2.6 KiB
61 lines
2.6 KiB
/// @file AP_MotorsSingle.h |
|
/// @brief Motor and Servo control class for Singlecopters |
|
#pragma once |
|
|
|
#include <AP_Common/AP_Common.h> |
|
#include <AP_Math/AP_Math.h> // ArduPilot Mega Vector/Matrix math Library |
|
#include <SRV_Channel/SRV_Channel.h> |
|
#include "AP_MotorsMulticopter.h" |
|
|
|
// feedback direction |
|
#define AP_MOTORS_SING_POSITIVE 1 |
|
#define AP_MOTORS_SING_NEGATIVE -1 |
|
|
|
#define NUM_ACTUATORS 4 |
|
|
|
#define AP_MOTORS_SINGLE_SPEED_DIGITAL_SERVOS 250 // update rate for digital servos |
|
#define AP_MOTORS_SINGLE_SPEED_ANALOG_SERVOS 125 // update rate for analog servos |
|
|
|
#define AP_MOTORS_SINGLE_SERVO_INPUT_RANGE 4500 // roll or pitch input of -4500 will cause servos to their minimum (i.e. radio_min), +4500 will move them to their maximum (i.e. radio_max) |
|
|
|
/// @class AP_MotorsSingle |
|
class AP_MotorsSingle : public AP_MotorsMulticopter { |
|
public: |
|
|
|
/// Constructor |
|
AP_MotorsSingle(uint16_t loop_rate, uint16_t speed_hz = AP_MOTORS_SPEED_DEFAULT) : |
|
AP_MotorsMulticopter(loop_rate, speed_hz) |
|
{ |
|
}; |
|
|
|
// init |
|
void init(motor_frame_class frame_class, motor_frame_type frame_type) override; |
|
|
|
// set frame class (i.e. quad, hexa, heli) and type (i.e. x, plus) |
|
void set_frame_class_and_type(motor_frame_class frame_class, motor_frame_type frame_type) override; |
|
|
|
// set update rate to motors - a value in hertz |
|
void set_update_rate( uint16_t speed_hz ) override; |
|
|
|
// output_to_motors - sends minimum values out to the motors |
|
virtual void output_to_motors() override; |
|
|
|
// get_motor_mask - returns a bitmask of which outputs are being used for motors or servos (1 means being used) |
|
// this can be used to ensure other pwm outputs (i.e. for servos) do not conflict |
|
uint32_t get_motor_mask() override; |
|
|
|
protected: |
|
// output - sends commands to the motors |
|
void output_armed_stabilizing() override; |
|
|
|
const char* _get_frame_string() const override { return "SINGLE"; } |
|
|
|
// output_test_seq - spin a motor at the pwm value specified |
|
// motor_seq is the motor's sequence number from 1 to the number of motors on the frame |
|
// pwm value is an actual pwm value that will be output, normally in the range of 1000 ~ 2000 |
|
virtual void _output_test_seq(uint8_t motor_seq, int16_t pwm) override; |
|
|
|
int16_t _throttle_radio_output; // total throttle pwm value, summed onto throttle channel minimum, typically ~1100-1900 |
|
float _actuator_out[NUM_ACTUATORS]; // combined roll, pitch, yaw and throttle outputs to motors in 0~1 range |
|
float _thrust_out; |
|
};
|
|
|