You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
146 lines
2.9 KiB
146 lines
2.9 KiB
g# hw definition file for processing by chibios_pins.py |
|
|
|
# MCU class and specific type |
|
MCU STM32F303 STM32F303xC |
|
|
|
# bootloader starts firmware at 26k |
|
FLASH_RESERVE_START_KB 26 |
|
|
|
# store parameters in pages 11 and 12 |
|
define STORAGE_FLASH_PAGE 11 |
|
define HAL_STORAGE_SIZE 800 |
|
|
|
# board ID for firmware load |
|
APJ_BOARD_ID 1004 |
|
|
|
# setup build for a peripheral firmware |
|
env AP_PERIPH 1 |
|
|
|
# enable watchdog |
|
define HAL_WATCHDOG_ENABLED_DEFAULT true |
|
|
|
# crystal frequency |
|
OSCILLATOR_HZ 8000000 |
|
|
|
define CH_CFG_ST_FREQUENCY 1000 |
|
|
|
# assume the 256k flash part for now |
|
FLASH_SIZE_KB 256 |
|
|
|
# board voltage |
|
STM32_VDD 330U |
|
|
|
# order of UARTs |
|
UART_ORDER USART2 USART1 |
|
|
|
# a LED to flash |
|
PA4 LED OUTPUT LOW |
|
|
|
# USART1, connected to GPS |
|
PA9 USART1_TX USART1 SPEED_HIGH NODMA |
|
PA10 USART1_RX USART1 SPEED_HIGH NODMA |
|
|
|
# USART2 for debug |
|
PA2 USART2_TX USART2 SPEED_HIGH NODMA |
|
PA3 USART2_RX USART2 SPEED_HIGH NODMA |
|
|
|
define HAL_UART_NODMA |
|
|
|
# only one I2C bus in normal config |
|
PB6 I2C1_SCL I2C1 |
|
PB7 I2C1_SDA I2C1 |
|
|
|
PB0 MAG_CS CS |
|
|
|
# spi bus for compass |
|
PA5 SPI1_SCK SPI1 |
|
PA6 SPI1_MISO SPI1 |
|
PA7 SPI1_MOSI SPI1 |
|
|
|
SPIDEV rm3100 SPI1 DEVID1 MAG_CS MODE0 1*MHZ 1*MHZ |
|
|
|
# analog input |
|
# PA5 VIN5 ADC1 |
|
define HAL_USE_ADC FALSE |
|
define STM32_ADC_USE_ADC1 FALSE |
|
define HAL_DISABLE_ADC_DRIVER TRUE |
|
|
|
define HAL_NO_GPIO_IRQ |
|
define CH_CFG_ST_TIMEDELTA 0 |
|
#define CH_CFG_USE_DYNAMIC FALSE |
|
define SERIAL_BUFFERS_SIZE 512 |
|
define PORT_INT_REQUIRED_STACK 64 |
|
|
|
# avoid timer and RCIN threads to save memory |
|
define HAL_NO_TIMER_THREAD |
|
define HAL_NO_RCIN_THREAD |
|
|
|
define HAL_USE_RTC FALSE |
|
define DISABLE_SERIAL_ESC_COMM TRUE |
|
define NO_DATAFLASH TRUE |
|
|
|
define DMA_RESERVE_SIZE 0 |
|
|
|
define PERIPH_FW TRUE |
|
|
|
# MAIN_STACK is stack of initial thread |
|
MAIN_STACK 0x80 |
|
|
|
# PROCESS_STACK controls stack for main thread |
|
PROCESS_STACK 0x600 |
|
define HAL_DISABLE_LOOP_DELAY |
|
|
|
# enable CAN support |
|
PA11 CAN_RX CAN |
|
PA12 CAN_TX CAN |
|
define HAL_USE_CAN TRUE |
|
define STM32_CAN_USE_CAN1 TRUE |
|
|
|
define HAL_USE_I2C TRUE |
|
define STM32_I2C_USE_I2C1 TRUE |
|
|
|
define HAL_UART_MIN_TX_SIZE 256 |
|
define HAL_UART_MIN_RX_SIZE 128 |
|
|
|
define HAL_UART_STACK_SIZE 256 |
|
define STORAGE_THD_WA_SIZE 256 |
|
define IO_THD_WA_SIZE 256 |
|
|
|
define HAL_NO_GCS |
|
define HAL_NO_LOGGING |
|
define HAL_NO_MONITOR_THREAD |
|
|
|
define HAL_MINIMIZE_FEATURES 0 |
|
|
|
define HAL_BUILD_AP_PERIPH |
|
|
|
# only one I2C bus |
|
I2C_ORDER I2C1 |
|
|
|
COMPASS RM3100 SPI:rm3100 false ROTATION_NONE |
|
|
|
define HAL_I2C_CLEAR_ON_TIMEOUT 0 |
|
|
|
define HAL_DEVICE_THREAD_STACK 256 |
|
|
|
define AP_PARAM_MAX_EMBEDDED_PARAM 0 |
|
|
|
define HAL_PROBE_EXTERNAL_I2C_COMPASSES |
|
define HAL_I2C_INTERNAL_MASK 0 |
|
|
|
# disable dual GPS and GPS blending to save flash space |
|
define GPS_MAX_RECEIVERS 1 |
|
define GPS_MAX_INSTANCES 1 |
|
define HAL_COMPASS_MAX_SENSORS 1 |
|
|
|
# use the app descriptor needed by MissionPlanner for CAN upload |
|
env APP_DESCRIPTOR MissionPlanner |
|
|
|
# reserve 256 bytes for comms between app and bootloader |
|
RAM_RESERVE_START 256 |
|
|
|
# define CH_DBG_ENABLE_STACK_CHECK TRUE |
|
|
|
# keep ROMFS uncompressed as we don't have enough RAM |
|
# to uncompress the bootloader at runtime |
|
env ROMFS_UNCOMPRESSED True
|
|
|