|
|
|
|
#!nsh
|
|
|
|
|
|
|
|
|
|
echo "[init] 666_fmu_q_x550: PX4FMU Quad X550 with PWM outputs"
|
|
|
|
|
|
|
|
|
|
#
|
|
|
|
|
# Load default params for this platform
|
|
|
|
|
#
|
|
|
|
|
if param compare SYS_AUTOCONFIG 1
|
|
|
|
|
then
|
|
|
|
|
# Set all params here, then disable autoconfig
|
|
|
|
|
param set MC_ATTRATE_P 0.14
|
|
|
|
|
param set MC_ATTRATE_I 0
|
|
|
|
|
param set MC_ATTRATE_D 0.006
|
|
|
|
|
param set MC_ATT_P 5.5
|
|
|
|
|
param set MC_ATT_I 0
|
|
|
|
|
param set MC_ATT_D 0
|
|
|
|
|
param set MC_YAWPOS_D 0
|
|
|
|
|
param set MC_YAWPOS_I 0
|
|
|
|
|
param set MC_YAWPOS_P 0.6
|
|
|
|
|
param set MC_YAWRATE_D 0
|
|
|
|
|
param set MC_YAWRATE_I 0
|
|
|
|
|
param set MC_YAWRATE_P 0.08
|
|
|
|
|
param set RC_SCALE_PITCH 1
|
|
|
|
|
param set RC_SCALE_ROLL 1
|
|
|
|
|
param set RC_SCALE_YAW 3
|
|
|
|
|
|
|
|
|
|
param set SYS_AUTOCONFIG 0
|
|
|
|
|
param save
|
|
|
|
|
fi
|
|
|
|
|
|
|
|
|
|
#
|
|
|
|
|
# Force some key parameters to sane values
|
|
|
|
|
# MAV_TYPE 2 = quadrotor
|
|
|
|
|
#
|
|
|
|
|
param set MAV_TYPE 2
|
|
|
|
|
|
|
|
|
|
#
|
|
|
|
|
# Start MAVLink
|
|
|
|
|
#
|
|
|
|
|
mavlink start -d /dev/ttyS0 -b 57600
|
|
|
|
|
usleep 5000
|
|
|
|
|
|
|
|
|
|
#
|
|
|
|
|
# Start PWM output
|
|
|
|
|
#
|
|
|
|
|
fmu mode_pwm
|
|
|
|
|
|
|
|
|
|
#
|
|
|
|
|
# Load mixer
|
|
|
|
|
#
|
|
|
|
|
mixer load /dev/pwm_output /etc/mixers/FMU_quad_x.mix
|
|
|
|
|
|
|
|
|
|
#
|
|
|
|
|
# Set PWM output frequency
|
|
|
|
|
#
|
|
|
|
|
pwm -u 400 -m 0xff
|
|
|
|
|
|
|
|
|
|
#
|
|
|
|
|
# Start common for all multirotors apps
|
|
|
|
|
#
|
|
|
|
|
sh /etc/init.d/rc.multirotor
|
|
|
|
|
|
|
|
|
|
# Exit, because /dev/ttyS0 is needed for MAVLink
|
|
|
|
|
exit
|
