px4_autopilot/ROMFS/px4fmu_common/init.d/airframes/4250_teal

#!/bin/sh
#
# @name Teal One
#
# @type Quadrotor x
# @class Copter
#
# @board px4_fmu-v2 exclude
# @board px4_fmu-v3 exclude
# @board px4_fmu-v4pro exclude
# @board px4_fmu-v5 exclude
#
# @output MAIN1 motor 1
# @output MAIN2 motor 2
# @output MAIN3 motor 3
# @output MAIN4 motor 4
#
# @maintainer Matt McFadden <matt.mcfadden@tealdrones.com>
#

echo "Executing 4250_teal script."

sh /etc/init.d/rc.mc_defaults

set MIXER quad_x
set PWM_OUT 1234

if [ $AUTOCNF = yes ]
then
	# First thing, reset all params to default... EXCEPT THIS LIST
	param reset_nostart RC* COM_FLTMODE* LND_FLIGHT_T_* TC_* CAL_ACC* CAL_GYRO* CAL_MAG* SENS_BOARD* EKF2_MAGBIAS*

	# battery
	param set BAT_CAPACITY 2750
	param set BAT_CRIT_THR 0.15
	param set BAT_EMERGEN_THR 0.075
	param set BAT_LOW_THR 0.20
	param set BAT_N_CELLS 4
	param set BAT_R_INTERNAL 0.06
	param set BAT_SOURCE 1
	param set BAT_V_CHARGED 4.15
	param set BAT_V_DIV 11.1625
	param set BAT_V_EMPTY 3.65
	param set BAT_V_OFFS_CURR -0.0045

	# sensor calibration
	param set CAL_MAG0_ROT 0
	param set CAL_MAG_SIDES 63
	param set SENS_BOARD_ROT 0
	param set COM_ARM_MAG_ANG -1
	param set COM_ARM_EKF_AB 0.0032

	# circuit breakers
	param set CBRK_IO_SAFETY 22027
	param set CBRK_USB_CHK 197848

	# commander
	param set COM_DISARM_LAND 0.1
	# Return mode at critically low level, Land mode at current position if reaching dangerously low levels.
	param set COM_LOW_BAT_ACT 3

	# ekf2
	param set EKF2_AID_MASK 1
	param set EKF2_MAG_TYPE 1
	param set EKF2_GPS_CHECK 511
	param set EKF2_GPS_POS_X -0.04
	param set EKF2_IMU_POS_X -0.06
	param set EKF2_PCOEF_XN 0.1
	param set EKF2_PCOEF_XP -0.5
	param set EKF2_RNG_AID 1
	param set EKF2_RNG_A_VMAX 20
	param set EKF2_RNG_NOISE 0.2
	param set EKF2_MIN_RNG 0.07

	# gps
	param set GPS_UBX_DYNMODEL 7

	# geofence
	# Geofence violation action -- Warning.
	param set GF_ACTION 1

	# land detector
	param set LNDMC_XY_VEL_MAX 1
	# This is set high because we have lots of vibrations while in contact with ground.
	param set LNDMC_ROT_MAX 50

	# serial comms
	param set SER_TEL1_BAUD 921600
	param set SER_TEL2_BAUD 921600

	# mavlink stream configuration
	# TEL1 ttyS1 -- disabled. TX1 FTDI UART has issues.
	param set MAV_0_CONFIG 0
	param set MAV_0_RATE 800000

	# TEL2 ttyS2 -- Primary MAVLINK stream to companion computer.
	param set MAV_1_CONFIG 102
	param set MAV_1_RATE 800000

	# mc_att_control
	param set MC_ACRO_P_MAX 360
	param set MC_ACRO_R_MAX 360
	param set MC_ACRO_Y_MAX 360

	param set MC_ROLL_P 6
	param set MC_ROLLRATE_P 0.055
	param set MC_ROLLRATE_I 0.2
	param set MC_ROLLRATE_D 0.0012
	param set MC_ROLLRATE_MAX 180

	param set MC_PITCH_P 6.5
	param set MC_PITCHRATE_P 0.06
	param set MC_PITCHRATE_I 0.2
	param set MC_PITCHRATE_D 0.0012
	param set MC_PITCHRATE_MAX 180

	param set MC_YAW_P 1
	param set MC_YAWRATE_P 0.08
	param set MC_YAWRATE_I 0.08
	param set MC_YAWRATE_D 0
	param set MC_YAWRATE_MAX 180

	# Set to reduce voltage transients as seen by battery management system.
	param set MOT_SLEW_MAX 0.15

	#### CONTROLLER ###
	param set MPC_LAND_ALT1 8
	param set MPC_LAND_ALT2 5
	param set MPC_TKO_RAMP_T 0.75
	param set MPC_TKO_SPEED 0.75
	param set MPC_TILTMAX_LND 18
	param set MPC_TILTMAX_AIR 45
	param set MPC_MAN_TILT_MAX 45

	param set MPC_MANTHR_MAX 0.85
	param set MPC_MANTHR_MIN 0.15
	# Full throttle can trip over current protection on BMS.
	param set MPC_THR_MAX 0.85
	param set MPC_THR_MIN 0.15

	param set MPC_VEL_MANUAL 26.5
	# RTL speed, it was too fast and scaring people.
	param set MPC_XY_CRUISE 15

	param set MPC_MAN_Y_MAX 200

	param set MPC_JERK_MAX 5
	param set MPC_ACC_UP_MAX 10
	param set MPC_ACC_DOWN_MAX 10
	param set MPC_ACC_HOR 10
	param set MPC_ACC_HOR_MAX 15

	param set MPC_XY_P 1.15
	param set MPC_XY_VEL_P 0.14
	param set MPC_XY_VEL_I 0.014
	param set MPC_XY_VEL_D 0.014
	param set MPC_XY_VEL_MAX 26.5

	param set MPC_Z_P 0.85
	param set MPC_Z_VEL_P 0.25
	param set MPC_Z_VEL_I 0.085
	param set MPC_Z_VEL_D 0.02
	# Documentation says limit is 8.0, but does not seem to be enforced in code.
	param set MPC_Z_VEL_MAX_UP 20
	param set MPC_Z_VEL_MAX_DN 2.5
	#### CONTROLLER ###

	# navigator
	param set NAV_ACC_RAD 2.5
	# RC loss failsafe behavior -- hold mode.
	param set NAV_RCL_ACT 1

	# pwm control
	param set PWM_DISARMED 900
	param set PWM_MAX 1850
	param set PWM_MIN 1075
	# Oneshot125
	param set PWM_RATE 0

	# rtl
	param set RTL_DESCEND_ALT 5
	param set RTL_LAND_DELAY 5
	param set RTL_MIN_DIST 7.5
	param set RTL_RETURN_ALT 25

	# calibration
	param set CAL_ACC0_EN 1
	param set CAL_ACC1_EN 0
	#mpu6500
	param set CAL_ACC_PRIME 1442826

	param set CAL_GYRO0_EN 1
	param set CAL_GYRO1_EN 0
	#mpu6500
	param set CAL_GYRO_PRIME 2360330

	param set CAL_MAG0_EN 1
	param set CAL_MAG1_EN 0
	param set CAL_MAG_PRIME 265738

fi

# Logger mode. Default(1) + estimator replay(2) + thermal calibration(4)
param set SDLOG_PROFILE 6

# Do not start frsky_telemetry on port ttyS6 by default, PGA460 lives there. 500 is in arbitrary unused number.
param set TEL_FRSKY_CONFIG 500
# We want to make sure these always start
param set SENS_EN_PGA460 1
param set SENS_EN_THERMAL 1
param set SENS_EN_BATT 1