STM32 SDIO DMA setup was losing DMA priority

git-svn-id: https://nuttx.svn.sourceforge.net/svnroot/nuttx/trunk@5019 7fd9a85b-ad96-42d3-883c-3090e2eb8679

nuttx/ChangeLog

@@ -3143,4 +3143,7 @@
 	* arch/arm/*/stm32:  Add support for STM32 F107 "Connectivity Line" 
 	  Ethernet (contributed by Max Holtzberg).
 	* configs/olimex-stm32-p107:  Add board support for the Olimiex STM32-P107
-	   board (contributed by Max Holtzberg).
+	   board (contributed by Max Holtzberg).
+	* arch/arm/src/stm32/stm32f2xx_dma.c, stm32f4xx_dma.c, stm32_serial.c, and
+	  stm32_spic.c:  DMA priority was getting zeroed by STM32 F2/F4 DMA drivers
+	  so that all DMAs ran at the lowest priority.

nuttx/arch/arm/src/stm32/stm32_serial.c

@@ -132,6 +132,30 @@
  */
 
 #  define RXDMA_BUFFER_SIZE   32
+
+/* DMA priority */
+
+#  ifndef CONFIG_USART_DMAPRIO
+#    if defined(CONFIG_STM32_STM32F10XX)
+#      define CONFIG_USART_DMAPRIO  DMA_CCR_PRIMED
+#    elif defined(CONFIG_STM32_STM32F20XX) || defined(CONFIG_STM32_STM32F40XX)
+#      define CONFIG_USART_DMAPRIO  DMA_SCR_PRIMED
+#    else
+#      error "Unknown STM32 DMA"
+#    endif
+#  endif
+#  if defined(CONFIG_STM32_STM32F10XX)
+#    if (CONFIG_USART_DMAPRIO & ~DMA_CCR_PL_MASK) != 0
+#      error "Illegal value for CONFIG_USART_DMAPRIO"
+#    endif
+#  elif defined(CONFIG_STM32_STM32F20XX) || defined(CONFIG_STM32_STM32F40XX)
+#    if (CONFIG_USART_DMAPRIO & ~DMA_SCR_PL_MASK) != 0
+#      error "Illegal value for CONFIG_USART_DMAPRIO"
+#    endif
+#  else
+#    error "Unknown STM32 DMA"
+#  endif
+
 #endif
 
 /* Power management definitions */
@@ -975,6 +999,7 @@ static int up_dma_setup(struct uart_dev_s *dev)
                  DMA_SCR_MINC          |
                  DMA_SCR_PSIZE_8BITS   |
                  DMA_SCR_MSIZE_8BITS   |
+                 CONFIG_USART_DMAPRIO  |
                  DMA_SCR_PBURST_SINGLE |
                  DMA_SCR_MBURST_SINGLE);
 

nuttx/arch/arm/src/stm32/stm32_spi.c

@@ -88,18 +88,47 @@
  * Definitions
  ************************************************************************************/
 /* Configuration ********************************************************************/
+/* SPI interrupts */
 
 #ifdef CONFIG_STM32_SPI_INTERRUPTS
 #  error "Interrupt driven SPI not yet supported"
 #endif
 
+/* Can't have both interrupt driven SPI and SPI DMA */
+
 #if defined(CONFIG_STM32_SPI_INTERRUPTS) && defined(CONFIG_STM32_SPI_DMA)
 #  error "Cannot enable both interrupt mode and DMA mode for SPI"
 #endif
 
-/* DMA channel configuration */
+/* SPI DMA priority */
+
+#ifdef CONFIG_STM32_SPI_DMA
+
+#  if defined(CONFIG_SPI_DMAPRIO)
+#    define SPI_DMA_PRIO  CONFIG_SPI_DMAPRIO
+#  elif defined(CONFIG_STM32_STM32F10XX)
+#    define SPI_DMA_PRIO  DMA_CCR_PRIMED
+#  elif defined(CONFIG_STM32_STM32F20XX) || defined(CONFIG_STM32_STM32F40XX)
+#    define SPI_DMA_PRIO  DMA_SCR_PRIMED
+#  else
+#    error "Unknown STM32 DMA"
+#  endif
 
-#define SPI_DMA_PRIO              DMA_CCR_PRIMED /* Check this to alter priority */
+#  if defined(CONFIG_STM32_STM32F10XX)
+#    if (SPI_DMA_PRIO & ~DMA_CCR_PL_MASK) != 0
+#      error "Illegal value for CONFIG_SPI_DMAPRIO"
+#    endif
+#  elif defined(CONFIG_STM32_STM32F20XX) || defined(CONFIG_STM32_STM32F40XX)
+#    if (SPI_DMA_PRIO & ~DMA_SCR_PL_MASK) != 0
+#      error "Illegal value for CONFIG_SPI_DMAPRIO"
+#    endif
+#  else
+#    error "Unknown STM32 DMA"
+#  endif
+
+#endif
+
+/* DMA channel configuration */
 
 #define SPI_RXDMA16_CONFIG        (SPI_DMA_PRIO|DMA_CCR_MSIZE_16BITS|DMA_CCR_PSIZE_16BITS|DMA_CCR_MINC            )
 #define SPI_RXDMA8_CONFIG         (SPI_DMA_PRIO|DMA_CCR_MSIZE_8BITS |DMA_CCR_PSIZE_8BITS |DMA_CCR_MINC            )

nuttx/arch/arm/src/stm32/stm32f20xxx_dma.c

@@ -721,11 +721,11 @@ void stm32_dmasetup(DMA_HANDLE handle, uint32_t paddr, uint32_t maddr,
   regval  = dmast_getreg(dmast, STM32_DMA_SCR_OFFSET);
   regval &= ~(DMA_SCR_PFCTRL|DMA_SCR_DIR_MASK|DMA_SCR_PINC|DMA_SCR_MINC|
               DMA_SCR_PSIZE_MASK|DMA_SCR_MSIZE_MASK|DMA_SCR_PINCOS|
-              DMA_SCR_CIRC|DMA_SCR_DBM|DMA_SCR_CT|
+              DMA_SCR_CIRC|DMA_SCR_DBM|DMA_SCR_CT|DMA_SCR_PL_MASK|
               DMA_SCR_PBURST_MASK|DMA_SCR_MBURST_MASK);
   scr    &=  (DMA_SCR_PFCTRL|DMA_SCR_DIR_MASK|DMA_SCR_PINC|DMA_SCR_MINC|
               DMA_SCR_PSIZE_MASK|DMA_SCR_MSIZE_MASK|DMA_SCR_PINCOS|
-              DMA_SCR_DBM|DMA_SCR_CIRC|
+              DMA_SCR_DBM|DMA_SCR_CIRC|DMA_SCR_PL_MASK|
               DMA_SCR_PBURST_MASK|DMA_SCR_MBURST_MASK);
   regval |= scr;
   dmast->nonstop = (scr & (DMA_SCR_DBM|DMA_SCR_CIRC)) != 0;

nuttx/arch/arm/src/stm32/stm32f40xxx_dma.c

@@ -721,11 +721,11 @@ void stm32_dmasetup(DMA_HANDLE handle, uint32_t paddr, uint32_t maddr,
   regval  = dmast_getreg(dmast, STM32_DMA_SCR_OFFSET);
   regval &= ~(DMA_SCR_PFCTRL|DMA_SCR_DIR_MASK|DMA_SCR_PINC|DMA_SCR_MINC|
               DMA_SCR_PSIZE_MASK|DMA_SCR_MSIZE_MASK|DMA_SCR_PINCOS|
-              DMA_SCR_CIRC|DMA_SCR_DBM|DMA_SCR_CT|
+              DMA_SCR_CIRC|DMA_SCR_DBM|DMA_SCR_CT|DMA_SCR_PL_MASK|
               DMA_SCR_PBURST_MASK|DMA_SCR_MBURST_MASK);
   scr    &=  (DMA_SCR_PFCTRL|DMA_SCR_DIR_MASK|DMA_SCR_PINC|DMA_SCR_MINC|
               DMA_SCR_PSIZE_MASK|DMA_SCR_MSIZE_MASK|DMA_SCR_PINCOS|
-              DMA_SCR_DBM|DMA_SCR_CIRC|
+              DMA_SCR_DBM|DMA_SCR_CIRC|DMA_SCR_PL_MASK|
               DMA_SCR_PBURST_MASK|DMA_SCR_MBURST_MASK);
   regval |= scr;
   dmast->nonstop = (scr & (DMA_SCR_DBM|DMA_SCR_CIRC)) != 0;