Merge remote-tracking branch 'upstream/master' into fw_autoland_att_tecs_navigator_termination_controlgroups

Conflicts:
	src/modules/px4iofirmware/registers.c

src/drivers/drv_rc_input.h

@@ -89,7 +89,7 @@ struct rc_input_values {
 	/** number of channels actually being seen */
 	uint32_t		channel_count;
 
-	/** receive signal strength indicator (RSSI): < 0: Undefined, 0: no signal, 1000: full reception */
+	/** receive signal strength indicator (RSSI): < 0: Undefined, 0: no signal, 255: full reception */
 	int32_t			rssi;
 
 	/** Input source */

src/drivers/px4io/px4io.cpp

@@ -1801,6 +1801,16 @@ PX4IO::print_status()
 		printf(" %u", io_reg_get(PX4IO_PAGE_RAW_RC_INPUT, PX4IO_P_RAW_RC_BASE + i));
 
 	printf("\n");
+
+	if (raw_inputs > 0) {
+		int frame_len = io_reg_get(PX4IO_PAGE_STATUS, PX4IO_P_STATUS_RC_DATA);
+		printf("RC data (PPM frame len) %u us\n", frame_len);
+
+		if ((frame_len - raw_inputs * 2000 - 3000) < 0) {
+			printf("WARNING  WARNING  WARNING! This RC receiver does not allow safe frame detection.\n");
+		}
+	}
+
 	uint16_t mapped_inputs = io_reg_get(PX4IO_PAGE_RC_INPUT, PX4IO_P_RC_VALID);
 	printf("mapped R/C inputs 0x%04x", mapped_inputs);
 

src/drivers/stm32/drv_hrt.c

@@ -282,6 +282,10 @@ static void		hrt_call_invoke(void);
  * Note that we assume that M3 means STM32F1 (since we don't really care about the F2).
  */
 # ifdef CONFIG_ARCH_CORTEXM3
+#  undef GTIM_CCER_CC1NP
+#  undef GTIM_CCER_CC2NP
+#  undef GTIM_CCER_CC3NP
+#  undef GTIM_CCER_CC4NP
 #  define GTIM_CCER_CC1NP 0
 #  define GTIM_CCER_CC2NP 0
 #  define GTIM_CCER_CC3NP 0
@@ -332,10 +336,10 @@ static void		hrt_call_invoke(void);
 /*
  * PPM decoder tuning parameters
  */
-# define PPM_MAX_PULSE_WIDTH	550		/* maximum width of a valid pulse */
+# define PPM_MAX_PULSE_WIDTH	700		/* maximum width of a valid pulse */
 # define PPM_MIN_CHANNEL_VALUE	800		/* shortest valid channel signal */
 # define PPM_MAX_CHANNEL_VALUE	2200		/* longest valid channel signal */
-# define PPM_MIN_START		2500		/* shortest valid start gap */
+# define PPM_MIN_START		2400		/* shortest valid start gap (only 2nd part of pulse) */
 
 /* decoded PPM buffer */
 #define PPM_MIN_CHANNELS	5
@@ -345,6 +349,7 @@ static void		hrt_call_invoke(void);
 #define PPM_CHANNEL_LOCK	4		/* should be less than the input timeout */
 
 __EXPORT uint16_t ppm_buffer[PPM_MAX_CHANNELS];
+__EXPORT uint16_t ppm_frame_length = 0;
 __EXPORT unsigned ppm_decoded_channels = 0;
 __EXPORT uint64_t ppm_last_valid_decode = 0;
 
@@ -362,7 +367,8 @@ static uint16_t ppm_temp_buffer[PPM_MAX_CHANNELS];
 struct {
 	uint16_t	last_edge;	/* last capture time */
 	uint16_t	last_mark;	/* last significant edge */
-	unsigned	next_channel;
+	uint16_t	frame_start;	/* the frame width */
+	unsigned	next_channel;	/* next channel index */
 	enum {
 		UNSYNCH = 0,
 		ARM,
@@ -447,7 +453,6 @@ hrt_ppm_decode(uint32_t status)
 
 	/* how long since the last edge? - this handles counter wrapping implicitely. */
 	width = count - ppm.last_edge;
-	ppm.last_edge = count;
 
 	ppm_edge_history[ppm_edge_next++] = width;
 
@@ -491,6 +496,7 @@ hrt_ppm_decode(uint32_t status)
 					ppm_buffer[i] = ppm_temp_buffer[i];
 
 				ppm_last_valid_decode = hrt_absolute_time();
+
 			}
 		}
 
@@ -500,13 +506,14 @@ hrt_ppm_decode(uint32_t status)
 		/* next edge is the reference for the first channel */
 		ppm.phase = ARM;
 
+		ppm.last_edge = count;
 		return;
 	}
 
 	switch (ppm.phase) {
 	case UNSYNCH:
 		/* we are waiting for a start pulse - nothing useful to do here */
-		return;
+		break;
 
 	case ARM:
 
@@ -515,14 +522,23 @@ hrt_ppm_decode(uint32_t status)
 			goto error;		/* pulse was too long */
 
 		/* record the mark timing, expect an inactive edge */
-		ppm.last_mark = count;
-		ppm.phase = INACTIVE;
-		return;
+		ppm.last_mark = ppm.last_edge;
+
+		/* frame length is everything including the start gap */
+		ppm_frame_length = (uint16_t)(ppm.last_edge - ppm.frame_start);
+		ppm.frame_start = ppm.last_edge;
+		ppm.phase = ACTIVE;
+		break;
 
 	case INACTIVE:
+
+		/* we expect a short pulse */
+		if (width > PPM_MAX_PULSE_WIDTH)
+			goto error;		/* pulse was too long */
+
 		/* this edge is not interesting, but now we are ready for the next mark */
 		ppm.phase = ACTIVE;
-		return;
+		break;
 
 	case ACTIVE:
 		/* determine the interval from the last mark */
@@ -543,10 +559,13 @@ hrt_ppm_decode(uint32_t status)
 			ppm_temp_buffer[ppm.next_channel++] = interval;
 
 		ppm.phase = INACTIVE;
-		return;
+		break;
 
 	}
 
+	ppm.last_edge = count;
+	return;
+
 	/* the state machine is corrupted; reset it */
 
 error:

src/modules/px4iofirmware/controls.c

@@ -50,7 +50,7 @@
 #define RC_CHANNEL_HIGH_THRESH		5000
 #define RC_CHANNEL_LOW_THRESH		-5000
 
-static bool	ppm_input(uint16_t *values, uint16_t *num_values);
+static bool	ppm_input(uint16_t *values, uint16_t *num_values, uint16_t *frame_len);
 
 static perf_counter_t c_gather_dsm;
 static perf_counter_t c_gather_sbus;
@@ -94,7 +94,7 @@ controls_tick() {
 	 * other.  Don't do that.
 	 */
 
-	/* receive signal strenght indicator (RSSI). 0 = no connection, 1000: perfect connection */
+	/* receive signal strenght indicator (RSSI). 0 = no connection, 255: perfect connection */
 	uint16_t rssi = 0;
 
 	perf_begin(c_gather_dsm);
@@ -108,7 +108,7 @@ controls_tick() {
 		else
 			r_status_flags &= ~PX4IO_P_STATUS_FLAGS_RC_DSM11;
 
-		rssi = 1000;
+		rssi = 255;
 	}
 	perf_end(c_gather_dsm);
 
@@ -125,11 +125,11 @@ controls_tick() {
 	 * disable the PPM decoder completely if we have S.bus signal.
 	 */
 	perf_begin(c_gather_ppm);
-	bool ppm_updated = ppm_input(r_raw_rc_values, &r_raw_rc_count);
+	bool ppm_updated = ppm_input(r_raw_rc_values, &r_raw_rc_count, &r_page_status[PX4IO_P_STATUS_RC_DATA]);
 	if (ppm_updated) {
 
 		/* XXX sample RSSI properly here */
-		rssi = 1000;
+		rssi = 255;
 
 		r_status_flags |= PX4IO_P_STATUS_FLAGS_RC_PPM;
 	}
@@ -321,7 +321,7 @@ controls_tick() {
 }
 
 static bool
-ppm_input(uint16_t *values, uint16_t *num_values)
+ppm_input(uint16_t *values, uint16_t *num_values, uint16_t *frame_len)
 {
 	bool result = false;
 
@@ -345,6 +345,10 @@ ppm_input(uint16_t *values, uint16_t *num_values)
 		/* clear validity */
 		ppm_last_valid_decode = 0;
 
+		/* store PPM frame length */
+		if (num_values)
+			*frame_len = ppm_frame_length;
+
 		/* good if we got any channels */
 		result = (*num_values > 0);
 	}

src/modules/px4iofirmware/protocol.h

@@ -128,7 +128,8 @@
 #define PX4IO_P_STATUS_VSERVO			6	/* [2] servo rail voltage in mV */
 #define PX4IO_P_STATUS_VRSSI			7	/* [2] RSSI voltage */
 #define PX4IO_P_STATUS_PRSSI			8	/* [2] RSSI PWM value */
-#define PX4IO_P_STATUS_NRSSI			9	/* [2] Normalized RSSI value, 0: no reception, 1000: perfect reception */
+#define PX4IO_P_STATUS_NRSSI			9	/* [2] Normalized RSSI value, 0: no reception, 255: perfect reception */
+#define PX4IO_P_STATUS_RC_DATA			10	/* [1] + [2] Details about the RC source (PPM frame length, Spektrum protocol type) */
 
 /* array of post-mix actuator outputs, -10000..10000 */
 #define PX4IO_PAGE_ACTUATORS		2		/* 0..CONFIG_ACTUATOR_COUNT-1 */

src/modules/px4iofirmware/registers.c

@@ -89,7 +89,9 @@ uint16_t		r_page_status[] = {
 	[PX4IO_P_STATUS_IBATT]			= 0,
 	[PX4IO_P_STATUS_VSERVO]			= 0,
 	[PX4IO_P_STATUS_VRSSI]			= 0,
-	[PX4IO_P_STATUS_PRSSI]			= 0
+	[PX4IO_P_STATUS_PRSSI]			= 0,
+	[PX4IO_P_STATUS_NRSSI]			= 0,
+	[PX4IO_P_STATUS_RC_DATA]		= 0
 };
 
 /**

src/modules/px4iofirmware/sbus.c

@@ -280,7 +280,7 @@ sbus_decode(hrt_abstime frame_time, uint16_t *values, uint16_t *num_values, uint
 		*rssi = 100; // XXX magic number indicating bad signal, but not a signal loss (yet)
 	}
 
-	*rssi = 1000;
+	*rssi = 255;
 
 	return true;
 }

src/modules/systemlib/ppm_decode.h

@@ -57,6 +57,7 @@ __BEGIN_DECLS
  * PPM decoder state
  */
 __EXPORT extern uint16_t	ppm_buffer[PPM_MAX_CHANNELS];	/**< decoded PPM channel values */
+__EXPORT extern uint16_t	ppm_frame_length;				/**< length of the decoded PPM frame (includes gap) */
 __EXPORT extern unsigned	ppm_decoded_channels;	/**< count of decoded channels */
 __EXPORT extern hrt_abstime	ppm_last_valid_decode;	/**< timestamp of the last valid decode */