Add scripts for debugging with openocd

Note: We now use the version of stm32f4x that comes with openocd 0.7.0 or later

Debug/olimex-px4fmu-debug.cfg

@@ -0,0 +1,22 @@
+# program a bootable device load on a mavstation
+# To run type openocd -f mavprogram.cfg
+
+source [find interface/olimex-arm-usb-ocd-h.cfg]
+source [find px4fmu-v1-board.cfg]
+
+init
+halt
+
+# Find the flash inside this CPU
+flash probe 0
+
+# erase it (128 pages) then program and exit
+
+#flash erase_sector 0 0 127
+# stm32f1x mass_erase 0 
+
+# It seems that Pat's image has a start address offset of 0x1000 but the vectors need to be at zero, so fixbin.sh moves things around
+#flash write_bank 0 fixed.bin 0
+#flash write_image firmware.elf
+#shutdown
+

Debug/openocd.gdbinit

@@ -0,0 +1,7 @@
+target remote :3333
+mon reset halt
+mon poll
+mon cortex_m maskisr auto
+set mem inaccessible-by-default off
+set print pretty
+source Debug/PX4

Debug/px4fmu-v1-board.cfg

@@ -0,0 +1,6 @@
+# The latest defaults in OpenOCD 0.7.0 are actually prettymuch correct for the px4fmu
+
+# increase working area to 32KB for faster flash programming
+set WORKAREASIZE 0x8000
+
+source [find target/stm32f4x.cfg]

Debug/runopenocd.sh

@@ -0,0 +1 @@
+openocd -f interface/olimex-arm-usb-ocd-h.cfg -f Debug/stm32f4x.cfg

Debug/stm32f4x.cfg

@@ -1,64 +0,0 @@
-# script for stm32f2xxx
-
-if { [info exists CHIPNAME] } {
-   set  _CHIPNAME $CHIPNAME
-} else {
-   set  _CHIPNAME stm32f4xxx
-}
-
-if { [info exists ENDIAN] } {
-   set  _ENDIAN $ENDIAN
-} else {
-   set  _ENDIAN little
-}
-
-# Work-area is a space in RAM used for flash programming
-# By default use 64kB
-if { [info exists WORKAREASIZE] } {
-   set  _WORKAREASIZE $WORKAREASIZE
-} else {
-   set  _WORKAREASIZE 0x10000
-}
-
-# JTAG speed should be <= F_CPU/6. F_CPU after reset is 8MHz, so use F_JTAG = 1MHz
-#
-# Since we may be running of an RC oscilator, we crank down the speed a
-# bit more to be on the safe side. Perhaps superstition, but if are
-# running off a crystal, we can run closer to the limit. Note
-# that there can be a pretty wide band where things are more or less stable.
-jtag_khz 1000
-
-jtag_nsrst_delay 100
-jtag_ntrst_delay 100
-
-#jtag scan chain
-if { [info exists CPUTAPID ] } {
-   set _CPUTAPID $CPUTAPID
-} else {
-  # See STM Document RM0033
-  # Section 32.6.3 - corresponds to Cortex-M3 r2p0
-   set _CPUTAPID 0x4ba00477
-}
-jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
-
-if { [info exists BSTAPID ] } {
-   set _BSTAPID $BSTAPID
-} else {
-  # See STM Document RM0033
-  # Section 32.6.2
-  # 
-  set _BSTAPID 0x06413041
-}
-jtag newtap $_CHIPNAME bs -irlen 5 -expected-id $_BSTAPID
-
-set _TARGETNAME $_CHIPNAME.cpu
-target create $_TARGETNAME cortex_m3 -endian $_ENDIAN -chain-position $_TARGETNAME -rtos auto
-
-$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
-
-set _FLASHNAME $_CHIPNAME.flash
-flash bank $_FLASHNAME stm32f2x 0 0 0 0 $_TARGETNAME
-
-# if srst is not fitted use SYSRESETREQ to
-# perform a soft reset
-cortex_m3 reset_config sysresetreq