- GPSDrivers in PX4/Firmware (3e0d06c65167c0bd79c193ea75ca5c7959053ff7): bd72eb6794
- GPSDrivers current upstream: d6940d9c8c
- Changes: bd72eb6794...d6940d9c8c
d6940d9 2021-12-02 alexklimaj - Update F9P moving base with direct UART2 connection
eb0cb58 2021-11-25 sebastian - always using groundspeed for vel_m_s in ubx driver
0408160 2021-11-18 alexklimaj - Remove extra UART1 baudrate set
- use NuttX gdb script for nxthreads and thread backtrace
- update jlink_gdb_backtrace and jlink_debug_gdb helper targets to use
NuttX gdb script
- Debug/PX4 fix "perf" divide by zero
- Debug/PX4 add "dmesg"
This fixes a case where the px4 startup is not stopped when the
px4 process is killled using -SIGKILL against the px4 deamon.
In that case, the currently executing command/client is killed
and properly shutting down with result -1, however, the next command
is started anyway.
This means that the next time we try to run the simulation we get a
"PX4 daemon already running for instance 0" error and PX4 doesn't start
properly.
By adding exit on error, we properly exit in the case where the startup
script gets stopped/killed.
This should help when gzserver does not respond yet and we end up
without a model and hence can't connect later and time out.
This change also required a fix to prevent the tester to hang on
terminating all runners. By using poll instead of only read we can
prevent that and actually properly join the logger thread.
* ekf2: selector treat combined test ratio > 1 as a warning
* ekf2: wait for 1s of constant warning to trigger an instance switch
Co-authored-by: bresch <brescianimathieu@gmail.com>
Use the same memory allocation in sw_crypto driver as what is used in
src/lib/crypto libraries
In addition, in nuttx protected build, allocate all memory from kernel heap
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
There was an error that PX4_CRYPTO was cached accross variants, if it was
defined just for one variant.
This synchronizes the caching of BOARD_CRYPTO with other similar BOARD_ flags;
it is set as INTERNAL and "1" when enabled.
Also remove handling of BOARD_KEYSTORE; it is not used anywhere after
changing the crypto under src/drivers. If a separate keystore driver
is required, it is just selected as any other driver in px4board
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
This fixes the following compile error on Mac:
src/drivers/gps/gps.cpp:562:23: fatal error: use of undeclared identifier 'B921600'
case 921600: speed = B921600; break;
^
dmesg was locking the console buffer, then writing to stdout (a pipe in
the case of the MAVLink shell).
This might block, waiting for mavlink to read from the pipe. If however
mavlink tries to write to the console at that time, the lock is already
taken.
This patch avoids nested locking by using a separate buffer.
When scaling manual input, we should only use pitch -90 to +90 instead
of -180 to 180 degrees which leads to weird behavior as it gets passed
on by a quaternion.
It is possible to either set the keyfile locations in board configuration or
with the same environment variables as before.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
This is more logical place for the "backend" implementation than
directly under platform.
This also allows making other implementations as "real" drivers, as well as proper configuration via Kconfigs
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
PX4 BuildBot
Daniel Agar
PX4BuildBot
Matthias Grob
Julian Oes
Peter van der Perk
Jukka Laitinen
alexklimaj
David Lechner
David Jablonski
Thomas
Beat Küng
David Sidrane
benjinne