* MC_HTE: unitialize with hover_thrust parameter
* MC_HTE: constrain hover thrust setter between 0.1 and 0.9
* MC_HTE: integrate with land detector and velocity controller
* MCHoverThrustEstimator: Always publish an estimate even when not fusing measurements. This is required as the land detector and the position controller need to receive a hover thrust value.
* MC_HTE: use altitude agl threshold to start the estimator
local_position.z is relative to the origin of the EKF while dist_bottom
is above ground
Co-authored-by: bresch <brescianimathieu@gmail.com>
Channels belonging to a certain timer were not all grouped together.
This is required by the .first_channel_index and .last_channel_index data
members.
We introduce a new mixer geometry to solve the problem.
* add support for unmanned underwater vehicles:
* airframe uuv_generic + uuv_hippocammpus including mav_type = 12 for submarines
* mixer for UUVs with X-shaped thruster setup similar to quadcopter
* add module uuv_att_control for underwater robot attitude control
* add rc.uuv_defaults/apps for autostarting e.g. ekf2 and uuv_att_control app
- this is a new module for temperature compensation that consolidates the functionality previously handled in the sensors module (calculating runtime thermal corrections) and the events module (online thermal calibration)
- by collecting this functionality into a single module we can optionally disable it on systems where it's not used and save some flash (if disabled at build time) or memory (disabled at run time)
* parameter and logic to commander for triggering failsafe from external automatic trigger system.
* logic to startup script for enabling ATS. Added uORB publishing to pwm_input module.
* Refactored out CDev usage from pwm_input and ll40ls. Refactored out ll40ls specifics from pwm_input and cleaned up dead code.
This target was never fully supported and is heavily dependent on a number of DriverFramework drivers that have no in tree equivalents (bebop bus, flow, rangefinder, etc). Deleting this will make it easier to fully drop DriverFramework shortly.
When running in HITL mode, pwm_out_sim publishes actuator_outputs.
px4io unconditionally publishes the uOrb actuator_outputs. When HITL
is configured, the px4io copy of the uOrb has all zeros.
The result is that there are two publications, one valid, and one
all-zeros. This causes the HIL_ACTUATOR_CONTROLS mavlink message
to be incorrect (all-zeros) and the SERVO_OUTPUTS_RAW mavlink
message to be inconsistent, as it takes the data from one or the
other uOrb randomly each cycle.
The fix is to let px4io know that HITL is in effect when it is
started, and modify px4io to suppress publication in this case.
This is a bigger more complicated fix than I would like, but I
think it is conceptually correct.
Signed-off-by: Nik Langrind <langrind@gmail.com>
* Draco-R sensor orientation correction
* LL40LS sensor is not stable during I2C probing. More trials have been implemented.
* px4flow execution has been removed as rc script already running it
* GPS LED script repaired
* Off ICM20608 due to some bug?
* Removed i2c speed adjustment due to SMBUS.
* ms5611 test2 does not exist
* Baud rate has changed.
* Draco-R airframe parameters are updated.
* IFO and Draco parameters are updated
* Draco-R sensor orientation corrected
* Draco-R DSHOT supports
Lorenz Meier
Daniel Agar
Beat Küng
Katrin
JaeyoungLim
Daniel Duecker
Roman Dvořák
Jacob Dahl
JaeyoungLim
Matthias Grob
Nik Langrind
Oleg Kalachev
Pandacoolcool
Jacob Dahl
RomanBapst