* msg: Add EKF-GSF yaw estimator logging data
* ecl: update to version with EKF-GSF yaw estimator
* ekf2: Add param control and logging for EKF-GSF yaw estimator
* logger: Add logging for EKF-GSF yaw esimtator
* MC_HTE: unitialize with hover_thrust parameter
* MC_HTE: constrain hover thrust setter between 0.1 and 0.9
* MC_HTE: integrate with land detector and velocity controller
* MCHoverThrustEstimator: Always publish an estimate even when not fusing measurements. This is required as the land detector and the position controller need to receive a hover thrust value.
* MC_HTE: use altitude agl threshold to start the estimator
local_position.z is relative to the origin of the EKF while dist_bottom
is above ground
Co-authored-by: bresch <brescianimathieu@gmail.com>
* Add Drotek RM3100 mag to board_sensors
* update to single wire
* Fix inverted FMU outputs from 451af07472
* digital power module update for e9890d01d9
* board doesn't have battery monitoring through ADC or GPIO, rather through I2C only
This avoids the need for recalibration, and also cleans up other driver
ID's (merge separate accel/gyro).
The SPI address was previously set to a board-specific (arbitrary) value,
and is now set to 0. This will allow extending for multiple sensors of the
same type on the same bus.
Chip-select and SPI initialization uses the new config, whereas the drivers
still use the existing defines.
The configuration in board_config.h can be removed after all drivers are
updated.
* 8 kHz gyro, 4 kHz accel
* DLPF disabled
* scheduled using data ready interrupts
* FIFO is emptied at 1 kHz by default, but can adjusted via IMU_GYRO_RATEMAX from 250 Hz - 2000 kHz.
* On both px4_fmu-v4 and px4_fmu-v4pro the secondary IMU is an mpu9250 with the same driver
- refactor Run() into simple state machine
- perform reset and configuration in sensor bus thread
- when using data ready interrupt skip checking FIFO count
- fix periodic temperature sampling (rate limit to 1 Hz)
- refactor Run() into simple state machine
- perform reset and configuration in sensor bus thread
- when using data ready interrupt skip checking FIFO count
* Introduce "px4_arch_adc_reference_v"
* Revert "Introduce "px4_arch_adc_reference_v""
This reverts commit 93691fbbd55a1b8da8c190e225b318067d90399b.
* use structure to return sample count and vref at the same time
* Revert "use structure to return sample count and vref at the same time"
This reverts commit 9cfd1c173cda51495f766a3f678c2202d67725fd.
* Revert "Revert "Introduce "px4_arch_adc_reference_v"""
This reverts commit edb7f7603e4471163ffb0fc6fc62ad2e30336e91.
* fix missed reference
* remove unecessary channel specific vref
* Update src/drivers/drv_adc.h
Co-Authored-By: David Sidrane <David.Sidrane@Nscdg.com>
* Update src/drivers/drv_adc.h
Co-Authored-By: David Sidrane <David.Sidrane@Nscdg.com>
* Introduce BOARD_ADC_POS_REF_V
Co-authored-by: David Sidrane <David.Sidrane@Nscdg.com>
- checked register mechanism and simple watchdog
- driver checks for errors gradually and can reconfigure itself
- respect IMU_GYRO_RATEMAX at the driver level
- fixed sensor INT16_MIN and INT16_MAX handling (y & z axis are flipped before publishing)
- checked register mechanism and simple watchdog
- driver checks for errors gradually and can reconfigure itself
- respect IMU_GYRO_RATEMAX at the driver level
- fixed sensor INT16_MIN and INT16_MAX handling (y & z axis are flipped before publishing)
- increased sensor_gyro_fifo max size (enables running the driver much slower, but still transferring all raw data)
- PX4Accelerometer/PX4Gyroscope remove unnecessary memsets
Beat Küng
SalimTerryLi
Paul Riseborough
Daniel Agar
David Sidrane
modaltb
Julian Kent