- ekf2 can now run in multi-instance mode (currently up to 9 instances)
- in multi mode all estimates are published to alternate topics (eg estimator_attitude instead of vehicle_attitude)
- new ekf2 selector runs in multi-instance mode to monitor and compare all instances, selecting a primary (eg N x estimator_attitude => vehicle_attitude)
- sensors module accel & gyro inconsistency checks are now relative to the mean of all instances, rather than the current primary (when active ekf2 selector is responsible for choosing primary accel & gyro)
- existing consumers of estimator_status must check estimator_selector_status to select current primary instance status
- ekf2 single instance mode is still fully supported and the default
Co-authored-by: Paul Riseborough <gncsolns@gmail.com>
- add new parameter `IMU_GYRO_FFT_EN` to start
- add 75% overlap in buffer to increase FFT update rate
- space out FFT calls (no more than 1 per cycle)
- increase `IMU_GYRO_FFT_MIN` default
- decrease main stack usage
* Add techpod SITL target
This adds a SITL target forthe techpod fixedwing model
* Update sitl_gazebo submoudle
This submodule update includes the techpod UAV model
- drivers/tone_alarm: move to ModuleBase and purge CDev (/dev/tone_alarm0)
- drivers/tone_alarm: only run on tune_control publication (or scheduled note) rather than continuously
- drivers/tone_alarm: use HRT to schedule tone stop (prevents potential disruption)
- msg/tune_control: add tune_id numbering
- systemcmds/tune_control: add "error" special case tune_id
- move all tune_control publication to new uORB::PublicationQueued<>
- start tone_alarm immediately after board defaults are loaded to fix potential startup issues
- for SITL (or other boards with no TONE output) print common messages (startup, error, etc)
* Add jsbsim bridge to enable jsbsim for px4 SITL/HIL on jsbsim
This is a PX4 HIL/SITL integration into JSBSim. JSBSim is an open source flight dynamics model (http://jsbsim.sourceforge.net/)
Currently there are three models available which is the rascal, quadrotor_x, hexarotor_x integrated into the bridge.
The simulation can be run with the firmware with the following command for example
```
make px4_sitl jsbsim_rascal
```
The visualization is done flightgear and is done by the bridge sending UDP packets to flightgear. To disable the visualization `HEADLESS=1` when running the make command.
The simulation can be configured through the configuration files under the `config` directory through a xml file. Senor configurations, The xml file name should match the name of the model.
* Update Tools/sitl_run.sh
Co-authored-by: Beat Küng <beat-kueng@gmx.net>
Co-authored-by: Beat Küng <beat-kueng@gmx.net>
Nuttx now supports sh and source (.)
sh will open a new process for each invocation.
This means the child can not modify the parent
env. So we must use . to matain how nuttx worked.
Since rc.vehicle_setup is used in both we use
source and alis as we did with sh.
- moves process airframe deps to the tar generation, to ensure whenever
airframes are processed, the tar is extracted first.
This is required, because if the airframe processing is done on pruned
ROMFS, it's missing the tags.
- avoid using init.d/rcS in dependencies, use a separate file instead.
This is because pruning modifies the rcS, and the next rebuild was
seeing a changed rcS, resulting in unnecessary regeneration.
It loads the battery parameters but then overwrites them
with hardcoded values and it breaks the ModuleParams
parent/child hierarchy. Both is undesired.
* [WIP] i2c_spi_buses: add '-q' for quiet startup flag
And enable for optional board sensors.
* ROMFS: rc.sensors try starting all optional I2C sensors quietly
Co-authored-by: Daniel Agar <daniel@agar.ca>
- in practice this is mostly useful for identifying incorrect rotations
which we mostly have in 45 degree increments
- handling a vehicle on the ground can easily disturb one mag by more than 30 degrees, so this is often distracting noise
- the values of the parameters GND_MAX_ANG and GND_WHEEL_BASE are outdated. They belonged to another Rover setup.
- in the mixer file rover_diff_and_servo.main.mix the steering was controlled by roll, but in PX4 rover steering is controlled by yaw. And this was the reason why the attitude control did not work correctly
- the DF Robot GPX:Asurada rover has actual a steering angle of 60 degrees. And and wheel base of 0.17m. Parameter values in the airframe file are changed to this values
because we need to have SITL simulation as realistic as possible
compared to a real flight with default settings such that we
either fix the problems or adjust the defaults already in SITL testing.
Daniel Agar
Silvan Fuhrer
Thies Lennart Alff
SalimTerryLi
Beat Küng
Jaeyoung-Lim
David Sidrane
bazooka joe
Matthias Grob
Katrin Moritz
Daniel Leonard Robinson
SungTae Moon
Katrin
xdwgood