Durandal:Fix PLL settings
durandal-v1:Move I2C123, I2C4 to HSI.
Not liking using HSI but, F7 has, and in reality there is no
requerment for accuracy.
durandal-v1:board config set 400kHz on card probe
durandal-v1:Board SDMMC Clock Not greater then 25 mHz
durandal-v1:Fix PLL3 configuration typo and value
CI build config for holybro_durandal-v1
durandal-v1:Kconfig - add knob to ensure ARCH_MATH_H is kept
Upstream changes added ARCH_HAVE_MATH_H to protect from archs
without math.h from causing isses for users setting
CONFIG_ARCH_MATH_H and getting errors. PX4 provides a math.h
and we need CONFIG_ARCH_MATH_H set. So this Selects
ARCH_HAVE_MATH_H perserving CONFIG_ARCH_MATH_H a defconfig
Track master LED removal
durandal-v1: bmi055 -> bmi088
bmi088 is what the board uses
durandal-v1:add PX4IO support
durandal-v1 rc.board_sensors: start baro
durandal-v1: remove segway module
durandal:Run at 480 Mhz
durandal-v1: build thermal control module
durandal-v1: enable IMU thermal control by default
durandal-v1:Track upstream adc start moved to rc.board_sensors
durandal-v1:Track upstream mavlink start moved to rc.board_mavlink
- Startup was broken due to unnecessary cyclic check probably introduced during transition to work_queues
- Module never used other than on Teal One which had a hacky heater input GPIO, this enables usage on general boards
drivers: heater: reduce verbosity and simplify commandline options
- We prefer the linux way of only reporting errors and staying quiet when everything is functioning as designed
- Most of the commandline options just read out the values of the system parameters, and one can just check the parameter values directly.
sensor_params: make thermal control parameters system parameters
heater_params: make thermal control parameters system parameters
drivers: heater: remove pin control hacks
- px4_arch_configgpio(GPIO_HEATER_OUTPUT) directly inits the heater pin to OFF, and as a PUSHPULL (TTL totem pole) OUTPUT
drivers: heater: set default device ID to 0
px4_fmuv5:Needed PROGMEM
fmu-v5:Kconfig - add knob to ensure ARCH_MATH_H is kept
Upstream changes added ARCH_HAVE_MATH_H to protect from archs
without math.h from causing isses for users setting
CONFIG_ARCH_MATH_H and getting errors. PX4 provides a math.h
and we need CONFIG_ARCH_MATH_H set. So this Selects
ARCH_HAVE_MATH_H perserving CONFIG_ARCH_MATH_H a defconfig
px4_io - add knob to ensure ARCH_MATH_H is kept
Upstream changes added ARCH_HAVE_MATH_H to protect from archs
without math.h from causing isses for users setting
CONFIG_ARCH_MATH_H and getting errors. PX4 provides a math.h
and we need CONFIG_ARCH_MATH_H set. So this Selects
ARCH_HAVE_MATH_H perserving CONFIG_ARCH_MATH_H a defconfig
The interrupt driven card detect logic was enabled
but the auto mounter was not. That interrupt was
calling mmcsd_mediachange.
There is a reentrancy issues in the kinetis callback logic.
Toplevel calls mmcsd_mediachange calls SDIO_CALLBACKENABLE
that calls kinetis_callbackenable that calls kinetis_callback
that calls mmcsd_mediachange.
- matrix in PX4/Firmware (d3184c866c3012105c8950a9f6652a9722fa3296): 93d42947b6
- matrix current upstream: cd185c995b
- Changes: 93d42947b6...cd185c995bcd185c9 2019-11-13 Daniel Agar - add braces around statements and cleanup formatting (#107)
38e966c 2019-11-12 kritz - Add min, max, constrain function for Matrix (#105)
David Sidrane
Mohammed Kabir
Beat Küng
Daniel Agar
BazookaJoe1900
Claudio Micheli
PX4 BuildBot
TSC21