* Adds Timer15 to stm32_common, if the timer base is defined
* Adds Timer15 logic for DMA and AltFunc config on stm32h7 boards
* Adds TIM15 BDTR->MOE support in stm32_common timer init
* Adds support for TIM15 pwm channels on Matek H743 Slim
If the hardware support RESET lockout that has nArmed ANDed with VBUS
vbus_sense may drop during a param save which uses
BOARD_INDICATE_EXTERNAL_LOCKOUT_STATE to prevent external resets
while writing the params. If we are not armed and nARMRED is low
we are in such a lock out so ignore changes on VBUS_SENSE during this
time.
It was a mistake to mix these two together, it is simpler to implement the boardctl interface
for the protected build, if the boardctl ioctls are different
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
This adds an ioctl interface for NuttX protected build, allowing
system calls from user space to kernel for uORB, HRT and crypto
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
When building uORB for NuttX flat build, or for some other target, everything
works as before.
When building uORB for NuttX protected or kernel build, this does the following:
- The kernel side uORB library reigsters a boardctl handler for calls from userspace
and services the boardctl_ioctls by calling the actual uORB functions
- For user mode binaries, the uORBManager acts as a proxy, making boardctl_ioctl calls to the
kernel side
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
This is the case for boards with digital readout, like v5x, but still
enable the battery_status module for external analog driver options.
An alternative would be to not run battery_status depending on config.
SD is on SPI3 - correct pin mapping
Fix DMA Mapping for all SPI and RX DMA on U[S]ART RX
Fix Memory MAP SRAM size
Removed unused GPIO
Used proper I2C definitions
Ensure Watchdog is configured for debugging
Fixed FLASH param definitions
Removed unedded SPI init
matek_gnss-m9n-f4:Correct Board ID and Size
Build order SJF
Added Support for F40x
Split the px4_layer into user and kernel space libraries. Add some stubs for
user-space (e.g. version) where an interface to the kernel needs to be added
Use posix-versions for cpuload.cpp and print_load.cpp for userspace; these link to nuttx internals. This functinality could be built on top of posix (e.g. procfs) interfaces
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Since uORB is split into kernel and userspace parts, it is no longer possible to just
link uORB into px4_platform, which is used in both kernel and user side.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
For NuttX protected or kernel build, the prebuilds can't contain libraries which are
different for kernel and user-space in protected/kerenl builds
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
This adds the env option PX4_FUZZ which runs the LLVM libFuzzer which
throws random bytes at mavlink_receiver using MAVLink messages over UDP.
The MAVLink messages that are being sent are valid, so the CRC is
calculated but the payload and msgid, etc. are generally garbage, unless
the fuzzing gets a msgid right by chance.
As I understand it, libFuzzer watches the test coverage and will try to
execute as much of the code as possible.
Charles Cross
David Sidrane
Jukka Laitinen
Beat Küng
Daniel Agar
Peter van der Perk
Julian Oes
PX4 BuildBot