Change PID to 0x4b:
Holybro obtained their own PID and VID but APM did not follow
the PX4 convention of makeing the board_id (0x8b) match the PID)
Incorporated the Upstream Bootloader state sequencing checking change.
Change the usb cout to send all chars in 1 write.
* FW attitude controller, FW position controller and VTOL attitude controller subscribe to airspeed_validated topic
* add possibility to switch off the airspeed valid checks
* remove airspeed valid checks from commander
* clean up of VTOL transition logic
* Airspeed Selector: remove dynamic allocation of airspeed validators (depending on number of connected sensors) but do it statically for the maximum number allowed. Check for number of connected sensors not only during start up, but always when vehicle is disarmed.
* Airspeed Selector: change work queue from lp to att_pos_ctrl as this module is safety-critical
* add airspeed selector to px4_fmu-v2 defaults
Durandal:Fix PLL settings
durandal-v1:Move I2C123, I2C4 to HSI.
Not liking using HSI but, F7 has, and in reality there is no
requerment for accuracy.
durandal-v1:board config set 400kHz on card probe
durandal-v1:Board SDMMC Clock Not greater then 25 mHz
durandal-v1:Fix PLL3 configuration typo and value
CI build config for holybro_durandal-v1
durandal-v1:Kconfig - add knob to ensure ARCH_MATH_H is kept
Upstream changes added ARCH_HAVE_MATH_H to protect from archs
without math.h from causing isses for users setting
CONFIG_ARCH_MATH_H and getting errors. PX4 provides a math.h
and we need CONFIG_ARCH_MATH_H set. So this Selects
ARCH_HAVE_MATH_H perserving CONFIG_ARCH_MATH_H a defconfig
Track master LED removal
durandal-v1: bmi055 -> bmi088
bmi088 is what the board uses
durandal-v1:add PX4IO support
durandal-v1 rc.board_sensors: start baro
durandal-v1: remove segway module
durandal:Run at 480 Mhz
durandal-v1: build thermal control module
durandal-v1: enable IMU thermal control by default
durandal-v1:Track upstream adc start moved to rc.board_sensors
durandal-v1:Track upstream mavlink start moved to rc.board_mavlink
px4_fmuv5:Needed PROGMEM
fmu-v5:Kconfig - add knob to ensure ARCH_MATH_H is kept
Upstream changes added ARCH_HAVE_MATH_H to protect from archs
without math.h from causing isses for users setting
CONFIG_ARCH_MATH_H and getting errors. PX4 provides a math.h
and we need CONFIG_ARCH_MATH_H set. So this Selects
ARCH_HAVE_MATH_H perserving CONFIG_ARCH_MATH_H a defconfig
px4_io - add knob to ensure ARCH_MATH_H is kept
Upstream changes added ARCH_HAVE_MATH_H to protect from archs
without math.h from causing isses for users setting
CONFIG_ARCH_MATH_H and getting errors. PX4 provides a math.h
and we need CONFIG_ARCH_MATH_H set. So this Selects
ARCH_HAVE_MATH_H perserving CONFIG_ARCH_MATH_H a defconfig
The interrupt driven card detect logic was enabled
but the auto mounter was not. That interrupt was
calling mmcsd_mediachange.
There is a reentrancy issues in the kinetis callback logic.
Toplevel calls mmcsd_mediachange calls SDIO_CALLBACKENABLE
that calls kinetis_callbackenable that calls kinetis_callback
that calls mmcsd_mediachange.
David Sidrane
Daniel Agar
Silvan Fuhrer
Julien Lecoeur
Beat Küng