Instead of using a timeout to resend a mission item, we should directly
send the mission request again. This is needed because we removed the
automatic resending which lead to troubles.
This is an attempt to fix mission upload and download with QGC on a
lossy link. The way it should work according to the protocol on
https://mavlink.io/en/protocol/mission.html is that in general
the ground station should be concerned about timeouts and
retransmission. This means the autopilot does not need to retransmit by
itself but just answer requests.
This seems like it would make the transfer less robust, however, it
actually resolves an edge case where QGC fails to make requests because
it gets spammed by the autopilot and keeps resetting the timeout.
ROI yaw control: configure yawing capability of mount in vmount parameters.
If configured that mount has no yaw control, vehicle will yaw towards ROI, irrespective of MIS_YAWMODE.
Vehicle will behave according to MIS_YAWMODE when there is no ROI.
or receiving a command that we need to handle. This makes sure that we
don't drop commands, when the output mode is set to mavlink (in that case
the input topic is rate-limited, and each input change results in a
vehicle_command publication, which results in queueing up orb items if we
get vehicle_commands from other sources too).
The way the broadcast IP is currently fetched is by sending an ioctl()
request. The limitation of this is that the broadcast address may not
be set on the network interface (more specifically, it is usually not
set in docker containers). In those cases, it results in the broadcast
address becoming 0.0.0.0, which is not valid [1].
This fix uses the network IP and the netmask to compute the directed
broadcast address. This should be more reliable, as both of those are
always set on the network interface.
[1]: https://tools.ietf.org/html/rfc1122, section 3.2.1.3 (a)
* Cygwin: repaired NuttX build after 1f63d85869
all the NuttX specific WINTOOL define handling was skiped in cmake Make.defs generation
The Nuttx build is makfile based and needs its cygwin treatment
Additionally the ${PX4_SOURCE_DIR}/src/include which was added through cmake needs path conversion
The two root causes for the special handling are:
- ARM GCC for Windows doesn't support cygwin paths passed as an argument
so they need to be either relative or converted via cypath tool
- Symbolic links are totally different under Windows and because NuttX uses them extensively
it has special handling scripts that need to be fed with the correct defines
* Cygwin: NuttX include paths all converted in Make.defs.in
differentiate between WINTOOL define (MSYS & cygwin) and cygwin using uname command:
- MSYS needs symbolic link handling for ARM GCC but no path conversion
- Cygwin needs both
This fixes the case where a topic instance is already subscribed, and
advertised later. The subscriber will create the DeviceNode with default
priority, and the advertiser will just use the existing DeviceNode,
without updating to the requested priority.
This fixes the case where a new gimbal input gets lost in the output
throttling.
This is required because an input is potentially set only once and
then not computed again. In the failure case, control_data is set
to nullptr in subsequent calls and therefore not used for the output
calculation ever.
This resolves the case where a gimbal command assembled by
QGroundControl is rejected because the component id is set to 0 (for
all) and the component id of the vehicle is e.g. 1.
* add more logging to help with #8556
* log subscribed topics on mission start and test exit (pass or fail)
* use mavlink enums everywhere to avoid maintaining dictionary mappings and to have readable values
* log when the FCU advances to next mission item without satisfying the position reached offset/radius
* some renaming for readability
* log more state value changes (connected and MAV_STATUS)
ChristophTobler
Beat Küng
PX4 Jenkins
Julian Oes
Nicolas de Palezieux
DonLakeFlyer
Daniel Agar
Lorenz Meier
Jonas Vautherin
Matthias Grob
Simone Guscetti
Anthony Lamping
TSC21