- this simplifies the reset by allowing a notch filter to reset as
needed
- improves cascade initialization, on reset each filter will reset
properly from the previous
- uavcan firmware server no longer shuts down when arming (nodes might restart in flight)
- always handle UAVCAN parameters with or without the FW server active
- remove legacy ESC enumeration in FW server
To avoid weird cases where the altitude is different enough and
the offtrack state flies to the target altitude instead of the closest
point on the track between the waypoints.
So instead of fuzzing each and every PR for 10minutes, we just fuzz
30mins every 24 hours, at 6am UTC which should be a time when US and
Europe might be least active.
This adds the env option PX4_FUZZ which runs the LLVM libFuzzer which
throws random bytes at mavlink_receiver using MAVLink messages over UDP.
The MAVLink messages that are being sent are valid, so the CRC is
calculated but the payload and msgid, etc. are generally garbage, unless
the fuzzing gets a msgid right by chance.
As I understand it, libFuzzer watches the test coverage and will try to
execute as much of the code as possible.
- sensors/vehicle_imu: reset learned cal on any calibration change
during parameter update
- sensors/vehicle_imu: cleanup logic estimated bias -> calibration offset
saving
- don't invalidate saved calibration (the point is to keep the last valid)
- remove old debug code, etc
- sensors/vehicle_imu: notify parameter changes if accel or gyro
calibration has changed
- lib/sensor_calibration: add calibrated() and calibration_index()
getters, keep Accelerometer/Gyroscope/Magnetometer in sync
This is an attempt to fix the test failure where PX4 detects an RC
timeout presumably because the tester process mavsdk_tests is stalled
and does not send RC control messages in time.
The imu and sensor_combined data should not be used when it has not been
updated yet, otherwise this triggers a memory sanitizer warning:
Conditional jump or move depends on uninitialised value(s)
at 0x2DA7AA: __sanitizer_cov_trace_const_cmp1 (in build/px4_sitl_default-clang/bin/px4)
by 0x3C4E79: EKF2::Run() (src/modules/ekf2/EKF2.cpp:401)
by 0x6EB881: px4::WorkQueue::Run() (platforms/common/px4_work_queue/WorkQueue.cpp:187)
by 0x6ECB9D: px4::WorkQueueRunner(void*) (platforms/common/px4_work_queue/WorkQueueManager.cpp:230)
by 0x4C07258: start_thread (in /usr/lib/libpthread-2.33.so)
by 0x4D415E2: clone (in /usr/lib/libc-2.33.so)
Conditional jump or move depends on uninitialised value(s)
at 0x3C4E7C: EKF2::Run() (src/modules/ekf2/EKF2.cpp:401)
by 0x6EB881: px4::WorkQueue::Run() (platforms/common/px4_work_queue/WorkQueue.cpp:187)
by 0x6ECB9D: px4::WorkQueueRunner(void*) (platforms/common/px4_work_queue/WorkQueueManager.cpp:230)
by 0x4C07258: start_thread (in /usr/lib/libpthread-2.33.so)
by 0x4D415E2: clone (in /usr/lib/libc-2.33.so)
- introuce slew rate limiting of airspeed setpoint (with slew rate of 1 m/s/s)
- some refactoring and clean up
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
This prevents a memory sanitizer/valgrind warning:
Conditional jump or move depends on uninitialised value(s)
at 0x2DA536: __sanitizer_cov_trace_cmp4 (in build/px4_sitl_default-clang/bin/px4)
by 0x6590D8: FailureDetector::update(vehicle_status_s const&, vehicle_control_mode_s const&) (src/modules/commander/failure_detector/FailureDetector.cpp:76) by 0x3817DF: Commander::run() (src/modules/commander/Commander.cpp:2605)
by 0x38B10B: ModuleBase<Commander>::run_trampoline(int, char**) (platforms/common/include/px4_platform_common/module.h:180)
Julian Oes
Daniel Agar
bresch
Matthias Grob
Silvan Fuhrer
romain-chiap
PX4 BuildBot
PX4BuildBot