* msg: Add EKF-GSF yaw estimator logging data
* ecl: update to version with EKF-GSF yaw estimator
* ekf2: Add param control and logging for EKF-GSF yaw estimator
* logger: Add logging for EKF-GSF yaw esimtator
* MC_HTE: unitialize with hover_thrust parameter
* MC_HTE: constrain hover thrust setter between 0.1 and 0.9
* MC_HTE: integrate with land detector and velocity controller
* MCHoverThrustEstimator: Always publish an estimate even when not fusing measurements. This is required as the land detector and the position controller need to receive a hover thrust value.
* MC_HTE: use altitude agl threshold to start the estimator
local_position.z is relative to the origin of the EKF while dist_bottom
is above ground
Co-authored-by: bresch <brescianimathieu@gmail.com>
This avoids the need for recalibration, and also cleans up other driver
ID's (merge separate accel/gyro).
The SPI address was previously set to a board-specific (arbitrary) value,
and is now set to 0. This will allow extending for multiple sensors of the
same type on the same bus.
Chip-select and SPI initialization uses the new config, whereas the drivers
still use the existing defines.
The configuration in board_config.h can be removed after all drivers are
updated.
* 8 kHz gyro, 4 kHz accel
* DLPF disabled
* scheduled using data ready interrupts
* FIFO is emptied at 1 kHz by default, but can adjusted via IMU_GYRO_RATEMAX from 250 Hz - 2000 kHz.
* On both px4_fmu-v4 and px4_fmu-v4pro the secondary IMU is an mpu9250 with the same driver
- refactor Run() into simple state machine
- perform reset and configuration in sensor bus thread
- when using data ready interrupt skip checking FIFO count
- fix periodic temperature sampling (rate limit to 1 Hz)
- refactor Run() into simple state machine
- perform reset and configuration in sensor bus thread
- when using data ready interrupt skip checking FIFO count
- checked register mechanism and simple watchdog
- driver checks for errors gradually and can reconfigure itself
- respect IMU_GYRO_RATEMAX at the driver level
- fixed sensor INT16_MIN and INT16_MAX handling (y & z axis are flipped before publishing)
- checked register mechanism and simple watchdog
- driver checks for errors gradually and can reconfigure itself
- respect IMU_GYRO_RATEMAX at the driver level
- fixed sensor INT16_MIN and INT16_MAX handling (y & z axis are flipped before publishing)
- increased sensor_gyro_fifo max size (enables running the driver much slower, but still transferring all raw data)
- PX4Accelerometer/PX4Gyroscope remove unnecessary memsets
- reduces amount of board configuration required
- removes the cyclic dependency between io_timers_t and timer_io_channels_t
Fixes a bug in the fmuk66-v3 config: the 2. timer has 3 channels associated
not 2.
Fixes a bug in the modelai config: the 2. timer has 4 channels associated.
- it does nothing useful
- increases boot time by 2 seconds on pixhawk 4 due to a poll timeout:
IST8310 on I2C bus 3 at 0x0e (bus: 100 KHz, max: 400 KHz)
WARN [ist8310] ERROR: TIMEOUT 2
* add support for unmanned underwater vehicles:
* airframe uuv_generic + uuv_hippocammpus including mav_type = 12 for submarines
* mixer for UUVs with X-shaped thruster setup similar to quadcopter
* add module uuv_att_control for underwater robot attitude control
* add rc.uuv_defaults/apps for autostarting e.g. ekf2 and uuv_att_control app
Beat Küng
SalimTerryLi
Paul Riseborough
Daniel Agar
David Sidrane
Daniel Duecker
Roman Dvořák