* MC_HTE: unitialize with hover_thrust parameter
* MC_HTE: constrain hover thrust setter between 0.1 and 0.9
* MC_HTE: integrate with land detector and velocity controller
* MCHoverThrustEstimator: Always publish an estimate even when not fusing measurements. This is required as the land detector and the position controller need to receive a hover thrust value.
* MC_HTE: use altitude agl threshold to start the estimator
local_position.z is relative to the origin of the EKF while dist_bottom
is above ground
Co-authored-by: bresch <brescianimathieu@gmail.com>
Chip-select and SPI initialization uses the new config, whereas the drivers
still use the existing defines.
The configuration in board_config.h can be removed after all drivers are
updated.
- reduces amount of board configuration required
- removes the cyclic dependency between io_timers_t and timer_io_channels_t
Fixes a bug in the fmuk66-v3 config: the 2. timer has 3 channels associated
not 2.
Fixes a bug in the modelai config: the 2. timer has 4 channels associated.
- it does nothing useful
- increases boot time by 2 seconds on pixhawk 4 due to a poll timeout:
IST8310 on I2C bus 3 at 0x0e (bus: 100 KHz, max: 400 KHz)
WARN [ist8310] ERROR: TIMEOUT 2
- this is a new module for temperature compensation that consolidates the functionality previously handled in the sensors module (calculating runtime thermal corrections) and the events module (online thermal calibration)
- by collecting this functionality into a single module we can optionally disable it on systems where it's not used and save some flash (if disabled at build time) or memory (disabled at run time)
The interrupt driven card detect logic was enabled
but the auto mounter was not. That interrupt was
calling mmcsd_mediachange.
There is a reentrancy issues in the kinetis callback logic.
Toplevel calls mmcsd_mediachange calls SDIO_CALLBACKENABLE
that calls kinetis_callbackenable that calls kinetis_callback
that calls mmcsd_mediachange.
and remove the px4_ prefix, except for px4_config.h.
command to update includes:
for k in app.h atomic.h cli.h console_buffer.h defines.h getopt.h i2c.h init.h log.h micro_hal.h module.h module_params.h param.h param_macros.h posix.h sem.h sem.hpp shmem.h shutdown.h tasks.h time.h workqueue.h; do for i in $(grep -rl 'include <px4_'$k src platforms boards); do sed -i 's/#include <px4_'$k'/#include <px4_platform_common\/'$k/ $i; done; done
for in $(grep -rl 'include <px4_config.h' src platforms boards); do sed -i 's/#include <px4_config.h/#include <px4_platform_common\/px4_config.h'/ $i; done
Transitional headers for submodules are added (px4_{defines,log,time}.h)
* adds a work_queue systemcmd that will bring a tree view of all active work queues and work items
* WorkQueues now track attached WorkItems and will shutdown when the last WorkItem is detached
-moved rc.mavlink to the boards optional rc additions (now it's called rc.board_mavlink) to handle board specific mavlink needs (mavlink over usb, ethernet, additional streams, etc.)
-mavlink module will be responsible to usb defaults, therefore less args are needed to be passed to mavlink module if one wants to use mavlink over usb.
-the way to check if connection is usb is by it's designated variable and not by config mode.
This new airspeed module does:
-runns an airspeed validator for every airspeed sensor present, which checks measurement validity and estimates an airspeed scale
-selects another airspeed sensor if for the current one a failure is detected
-estimates airspeed with groundspeed-windspeed if no valid airspeed sensor is present
-outputs airspeed_validated topic
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
A board only needs to define:
#define RC_SERIAL_PORT "/dev/ttyS4"
Then it can optionally define one or more of the following:
#define RC_SERIAL_SWAP_RXTX
#define RC_SERIAL_SINGLEWIRE
#define RC_INVERT_INPUT(_invert_true) px4_arch_gpiowrite(GPIO_SBUS_INV, _invert_true)
Beat Küng
Daniel Agar
David Sidrane
garfieldG
BazookaJoe1900
Silvan Fuhrer