The bulk of this change was tightly coupled and needed to be deleted in one pass. Some of the smaller changes were things that broke as a result of the initial purge and subsequently fixed by further eradicating unnecessary platform differences. Finally, I deleted any dead code I came across in the related files I touched while going through everything.
- DriverFramework (src/lib/DriverFramework submodule) completely removed
- added dspal submodule in qurt platform (was brought in via DriverFramework)
- all df wrapper drivers removed
- all boards using df wrapper drivers updated to use in tree equivalents
- unused empty arch/board.h on posix and qurt removed
- unused IOCTLs removed (pub block, priv, etc)
- Integrator delete methods only used from df wrapper drivers
- commander: sensor calibration use "NuttX version" everywhere for now
- sensors: update to px4_{open, read, close} instead of DevMgr wrapper (adc open for analog differential pressure)
- battery_status: update to px4_{open, read, close} instead of DevMgr wrapper (adc open for analog differential pressure)
- cdev cleanup conflicting typedefs and names with actual OS (pollevent_t, etc)
- load_mon and top remove from linux boards (unused)
- delete unused PX4_MAIN_FUNCTION
- delete unused getreg32 macro
- delete unused SIOCDEVPRIVATE define
- named each platform tasks consistently
- posix list_devices and list_topics removed (list_files now shows all virtual files)
Setting PTHREAD_EXPLICIT_SCHED was necessary on linux to create WQ threads with priorities relative to max, but unfortunately we can't rely pthread_attr_setinheritsched as it's dependent on system ulimit configuration or running privileged. Instead we can create the wq:manager at the maximum desired priority and allow each WQ thread to have a relative priority.
- fixed df_ltc2946_wrapper battery dependency
- fixed px4::atomic fetch_add for QuRT
- updated PX4 QuRT SPI wrapper to set bus frequency
- renamed "qurt-default" configs to just "qurt"
- instrumenting PX4 Matrix and Param methods is too burdensome
- partially restore px4_fmu-v5_stackcheck and holybro_durandal-v1_stackcheck to match default configs
This target was never fully supported and is heavily dependent on a number of DriverFramework drivers that have no in tree equivalents (bebop bus, flow, rangefinder, etc). Deleting this will make it easier to fully drop DriverFramework shortly.
- deprecate DriverFramework bmp280 driver (df_bmp280_wrapper)
- update beaglebone blue and snapdragon flight eagle boards to use in tree bmp280
- update posix (really just linux) and qurt I2C wrappers
- tested on beaglebone blue
In general, if anything goes wrong in the startup script, we
should fail entirely because things might not work as expected.
In particular, this prevents that we have to press Ctrl+C twice if the
simulator start call is hung waiting for the simulator to appear and
start communicating. We now press Ctrl+C once and exit straightaway
whereas before we would press it once to get the warning:
"Startup script returned with return value: 2",
and then finally exit on the second press.
- nuttx in PX4/Firmware (327c7f3672ee5f066ec53dfe1554a02d1aa610da): 2e55ce8ec9
- nuttx current upstream: 9331fda0d7
- Changes: 2e55ce8ec9...9331fda0d7
9331fda0d7 2019-12-10 David Sidrane - [BACKPORT] IMXRT106x USDHC: Support regular GPIO for CD and inversion.
91c80c708b 2019-12-05 David Sidrane - [BACKPORT] imxrt106x:pinout add ALT 8 GPIO_GPT1_CAPTURE[1|2]
32f758f0e9 2019-12-03 David Sidrane - [BACKPORT] stm32f7:Add Serial Tx DMA
- added gazebo VTOL tailsitter debug target
- improved jmavsim debug target and helper tasks to work properly (build and launch directly instead of through the jmavsim_run.sh script)
- improved output console handling for helper tasks (eg gazebo and jmavsim build and run, followed by cleanup after debug)
- added miniterm.py as a task
- nuttx in PX4/Firmware (22a005c9f4): 2d7920055f
- nuttx current upstream: 398a59aaa4
- Changes: 2d7920055f...398a59aaa4
398a59aaa4 2019-11-29 David Sidrane - [BACKPORT] stm32f7:ethernet: Add some delays so that ifup() does not hog the CPU.
Change PID to 0x4b:
Holybro obtained their own PID and VID but APM did not follow
the PX4 convention of makeing the board_id (0x8b) match the PID)
Incorporated the Upstream Bootloader state sequencing checking change.
Change the usb cout to send all chars in 1 write.
Daniel Agar
David Sidrane
Julian Oes
Lorenz Meier
Christian Clauss
Chris Lovett
kamilritz
PX4 BuildBot
Matthias Grob
Beat Küng