px4_autopilot

Commit Graph

Author	SHA1	Message	Date
Daniel Agar	b277840233	boards: create px4_fmu-v5_debug build with assertions enabled	5 years ago
Beat Küng	03e51076b0	v5x: fix icm20602 sensor orientation and reorder baro startup, so that the other one is used by default.	5 years ago
Beat Küng	157ef43e28	replay: use lockstep scheduler	5 years ago
Daniel Agar	d9102ce54c	imu/invensense/icm20948: sync with other recent invensense improvements - clenaup ak09916 with simplifed setup and health check	5 years ago
David Sidrane	28a695dce4	px4_fmu-v6x:imu/bmi088->imu/bosch/bmi088	5 years ago
Daniel Agar	0a63df25a6	create fake_magnetometer "driver" to publish magnetic field in body frame - this can be helpful for orienting new unknown magnetometers - requires attitude and GPS position	5 years ago
Daniel Agar	e819f99064	new Bosch BMI055 IMU driver using FIFOs and DRDY - accel & gyro FIFOs enabled - FIFO watermark on data ready interrupt - sensor side filtering completely disabled - gyro now respects `IMU_GYRO_RATEMAX` (up to 2 kHz) - saves a few % cpu (at default rate)	5 years ago
Daniel Agar	13e34b32e6	new Bosch BMI088 IMU driver using FIFOs and DRDY	5 years ago
Daniel Agar	6f6efd60b7	boards: centralize optional external I2C sensor start - configured with new parameter SENS_EXT_I2C_PRB	5 years ago
David Sidrane	82b87adfb3	px4_fmu-v6x:default phy is LAN8742	5 years ago
David Sidrane	0bb8d7a065	px4_fmu-v5x p4 (-06) default to suporting LAN8742Ai	5 years ago
Daniel Agar	5e7d2e830d	boards: delete old board.h boilerplate	5 years ago
Daniel Agar	5507c15bdc	boards: move rgbled_pwm startup to appropriate boards	5 years ago
David Sidrane	626895eadc	px4_fmu-v5x:Wrong Bit was being tested for mode. @TSC21 - this will fix you build	5 years ago
Daniel Agar	31fe7af454	selectively increase optimization -Os -> -O2 - targetted at modules/libraries that benefit without drastically increasing flash usage - ignored on boards with CONSTRAINED_FLASH set	5 years ago
Daniel Agar	6c96748e54	boards: pixhawk mini add unused MPU9250 CS & DRDY pins	5 years ago
David Sidrane	73bb18a053	px4_fmu-v6x: Limit Slew rate So IMU works with DMA The defualt in NuttX is OSPEED of 50Mhz. This is realy a slew rate control. At the default high slew rate the overshoot was .7 Volts. On a ICM20649 this was causing the device to output garbage. All 0s N.B. A passive scope or Logic analyser's probes load will mask the failure. Useed a FET probe to verify the issue.	5 years ago
David Sidrane	5d90c31632	Added PX4 FmuV6X	5 years ago
Julian Kent	dd9c82eb20	systemcmds/gpio: Add nsh command to manipulate/read GPIO * Add basic GPIO test app for R/W on pins from nuttx shell * Add gpio command to fmu-v3 and fmu-v4 * Sanitize gpio commands by pin configs, --force to override	5 years ago
David Sidrane	04db5391fc	px4_fmu-v5x:Fix PG11 assignment	5 years ago
David Sidrane	b2153c7f2f	px4_fmu-v5x:PG6 is free GPIO	5 years ago
David Sidrane	7f84ed57dd	px4_fmu-v5x:Using SE050 not A71CH	5 years ago
David Sidrane	637578b8be	px4_fmu-v5x:Correct trace connector description	5 years ago
Beat Küng	9c6f42a867	v5x defconfig: increase TELEM2 UART TX buffer size to 3000 Required for very high-rate log streaming @3MBit baudrate.	5 years ago
Daniel Agar	678c3fe8e4	boards: px4_fmu-v5_optimized don't build all mags	5 years ago
Daniel Agar	746a8f5cf9	commander: reboot/shutdown usability fixes - always check with state machine before reboot/shutdown - respect BOARD_HAS_POWER_CONTROL (shutdown from command, low battery, power button) - px4_shutdown_request add optional delay and always execute from HPWORK - px4_shutdown_request split out px4_reboot_request	5 years ago
Daniel Agar	28d2aca699	boards: include all procfs entries on boards that aren't flash constrained	5 years ago
Daniel Agar	8d0c92003a	boards: remove all CONFIG_NXFONTS_DISABLE*	5 years ago
Daniel Agar	3e5f85b47b	uavcannode: add distance_sensor (all possible instances)	5 years ago
Jakub Kákona	dfa5ca1710	FlightGear simulator support (#14539 ) - Add flightgear_bridge submodule. - Add traget px4_sitl_nolockstep with disabled LOCKSTEP simulation. - Add flightgear viewer targets and startup scripts - Add a few possible vehicles plane (rascal), autogyro (tf-g1), and rover (tf-r1)) Co-authored-by: Vit Hanousek <vithanousek@seznam.cz>	5 years ago
Beat Küng	34c75f2d36	boards: temporarily disable UART TX DMA work-around for https://github.com/PX4/Firmware/issues/14659. This can be reverted when fixed properly.	5 years ago
Daniel Agar	5739cf27e5	boards: delete obsolete commented config systemcmd	5 years ago
Roman Dvořák	75fe3bee8c	drivers/rpm: add simple RPM message simulator (dummy publisher)	5 years ago
Daniel Agar	06478d9997	delete obsolete SENSORIOCSPOLLRATE/SENSORIOCRESET and systemcmds/config	5 years ago
Daniel Agar	7c7ee115e3	boards: px4_io-v2 defconfig optimizations to save memory * disable CONFIG_ARMV7M_MEMCPY to save flash * disable CONFIG_LIB_BOARDCTL * remove unnecessary pthread and task settings * reduce preallocated watchdogs * reduce console buffer size * reduce IDLE thread stack * reduce user main stack Co-Authored-By: David Sidrane <David.Sidrane@Nscdg.com>	5 years ago
mcsauder	6548fde024	Whitespace cleanup to quiet new blank line at EOF git hook.	5 years ago
Daniel Agar	1ac6230758	boards: always change default IMU_GYRO_RATEMAX on px4_fmu-v2/v3 and mro_x21 - this can lower cpu usage considerably on older boards	5 years ago
Daniel Agar	588195f46c	boards: px4/fmu-v4pro cleanup rc.board_sensors - board has either an icm20602 or icm20608g, not both - probe all typical externally compasses	5 years ago
Daniel Agar	66eacd24bc	px4_fmu-v5_stackcheck: update stack sizes and add to Jenkins - increase stack sizes to run cleanly under stackcheck - this is likely overkill for most boards, but using stackcheck to set our minimum ensures we have a very safe margin on regular builds and it's something we can currently afford - remove holybro_durandal-v1_stackcheck from test rack (there's only one unit)	5 years ago
Daniel Agar	276b2cad5a	boards: fmu was renamed pwm_out	5 years ago
Daniel Agar	55fc0cbdc7	boards/px4/fmu-v4: fix internal hmc5883 start	5 years ago
Beat Küng	31937c280d	px4/v4: enable tx dma on telem2	5 years ago
Beat Küng	cbed023334	px4/v{2,3}: enable tx dma on telem2	5 years ago
Beat Küng	68e1172bb5	px4/v5x: enable tx dma on telem2	5 years ago
Daniel Agar	a89bba470a	boards: STM32F76xxx/STM32F77xxx linker add ITCM RAM and .ramfuncs handling - this doesn't currently change anything, but gets us ready to start experimenting with using the small amount of instruction tightly memory on STM32F7 - the .ramfuncs section works with NuttX CONFIG_ARCH_RAMFUNCS	5 years ago
Daniel Agar	7aa7f0ed95	switch remaining boards to new InvenSense IMU drivers	5 years ago
Julian Oes	b01cdafcf6	boards: add esc_battery to build	5 years ago
Julian Oes	509b8b6b4b	First skeleton for esc_battery module	5 years ago
Daniel Agar	ad559a66a1	examples: add simple work_item example module	5 years ago
Daniel Agar	40b1043e12	NuttX boards minor lpwork and init stack increases	5 years ago

1 2 3 4 5 ...

393 Commits (9723b26d7241647644490467856d0d71d33c2588)