Instead of directly doing the link loss reaction which by default is RTL a delay
can be configured such that the drone first switches to hold and waits
for the link to be regained.
For some usecases like starting video recording on a companion computer or triggering a ROS based (offboard control) mission control execution the status of RC channel is needed in ROS(2). This allows the user to start/stop such functionalities from the RC transmitter.
Therefore InputRc to be changed accordingly.
add 'Set send: true' for id: 30
Add new DeviceBusType_SERIAL to Device::DeviceId union
Add DRV_DIST_DEVTYPE's for all distance sensors
Change distance_sensor_s.id to distance_sensor_s.device_id
Modify all distance_sensor drivers to apply 'proper' device_id
- control allocation module with multirotor, VTOL standard, and tiltrotor support
- angular_velocity_controller
- See https://github.com/PX4/PX4-Autopilot/pull/13351 for details
Co-authored-by: Silvan Fuhrer <silvan@auterion.com>
Co-authored-by: Roman Bapst <bapstroman@gmail.com>
- commander preflightcheck use estimator_sensor_bias message instead of EKF state index magic number
- ekf2 publish estimated bias limits in estimator_sensor_bias
- preflightcheck only error if bias estimate exceeds half of configured limit (delete COM_ARM_EKF_AB and COM_ARM_EKF_GB parameters)
- handle saving the mag bias per sensor (across all estimator instances using that mag) in sensors/vehicle_magnetometer
- this is now saving back to the actual mag calibration CAL_MAGn_OFF{X,Y,Z}
- ekf2 reset mag mag bias on any magnetometer or calibration change
- use Kalman filter scheme to update stored mag bias parameters using all available bias estimates for that sensor
Co-authored-by: Paul Riseborough <gncsolns@gmail.com>
- log all estimator (ekf2) flags as separate booleans in a new dedicated low rate message (only publishes at 1 Hz or immediately on any change)
- this is a bit verbose, but it avoids the duplicate bit definitions we currently have across PX4 msgs, ecl analysis script, flight review, and many other custom tools and it's much easier for casual log review in FlightPlot, PlotJuggler, csv, etc
- for compatibility I've left estimator_status filter_fault_flags, innovation_check_flags, and solution_status_flags in place, but they can gradually be removed as tooling is updated
Co-authored-by: Mathieu Bresciani <brescianimathieu@gmail.com>
Changed all 'NED' references to 'FRD'. Also cleaned up mixing of m/s/s and m/s^2 to use the latter. Corrected m/s/s to Pascals. Plus minor typos. Also made some minor cosmetic clean ups.
Co-authored-by: Robin <robin@Robins-MacBook-Pro-Work.local>
Co-authored-by: Mathieu Bresciani <brescianimathieu@gmail.com>
- split out switches from manual_control_setpoint into new message manual_control_switches
- manual_control_switches published at minimal rate (~ 1 Hz) or immediately on change
- simple switch debounce in rc_update (2 consecutive identical decodes required)
- manual_control_switches logged at full rate rather than sampled at (5-10% of messages logged)
- manual_control_setpoint publish at minimal rate unless changing
- commander handle landing gear switch for manual modes
- processing of mode_slot and mode_switch is now split so we only do one or the other (not both)
- a future step will be to finally drop mode_switch and accompanying switches entirely
Co-authored-by: Matthias Grob <maetugr@gmail.com>
Daniel Agar
Matthias Grob
Antonio Sanjurjo Cortés
Gerald
TSC21
Claudio Micheli
JacobCrabill
Silvan Fuhrer
David Sidrane
TheLegendaryJedi
Mathieu Bresciani
Beat Küng
Julien Lecoeur
Julian Kent
RomanBapst
bazooka joe
Robin Lilja
Igor Campos