* Add basic GPIO test app for R/W on pins from nuttx shell
* Add gpio command to fmu-v3 and fmu-v4
* Sanitize gpio commands by pin configs, --force to override
- always check with state machine before reboot/shutdown
- respect BOARD_HAS_POWER_CONTROL (shutdown from command, low battery, power button)
- px4_shutdown_request add optional delay and always execute from HPWORK
- px4_shutdown_request split out px4_reboot_request
- increase stack sizes to run cleanly under stackcheck
- this is likely overkill for most boards, but using stackcheck to set our minimum ensures we have a very safe margin on regular builds and it's something we can currently afford
- remove holybro_durandal-v1_stackcheck from test rack (there's only one unit)
- interupt pin set active low and latch
- relax retry timeout if configure failed
- improve configured empty rate (sample rate) rounding
- fix RegisterCheck
- check FIFO count as part of full transfer and reset or adjust timing if necessary
- rename DRV_IMU_DEVTYPE_ICM20608 -> DRV_IMU_DEVTYPE_ICM20608G
- update to NuttX with stm32f4 and stm32f7 SPI DMA internal buffers
- remove explicit DMA buffer allocations from new IMU drivers
- restore original BOARD_DMA_ALLOC_POOL_SIZE
- decrease SPI DMA thresholds based on fmu-v2/v3/v4/v5 bench testing
This is another new InvenSense sensor with max output data rate of 32 kHz (both accel & gyro), on board anti-aliasing filter, and accel range 32G. Overall quite similar to the ICM-42688-P added in #14420, but with doubled accel range and without the optional high resolution output or clock sync.
Removes the calibration on startup, as these values were overwritten by
the system calibration values anyway.
So the only difference is that if all calibration scales were equal to 1,
the driver startup would have failed.
* MC_HTE: unitialize with hover_thrust parameter
* MC_HTE: constrain hover thrust setter between 0.1 and 0.9
* MC_HTE: integrate with land detector and velocity controller
* MCHoverThrustEstimator: Always publish an estimate even when not fusing measurements. This is required as the land detector and the position controller need to receive a hover thrust value.
* MC_HTE: use altitude agl threshold to start the estimator
local_position.z is relative to the origin of the EKF while dist_bottom
is above ground
Co-authored-by: bresch <brescianimathieu@gmail.com>
Chip-select and SPI initialization uses the new config, whereas the drivers
still use the existing defines.
The configuration in board_config.h can be removed after all drivers are
updated.
* 8 kHz gyro, 4 kHz accel
* DLPF disabled
* scheduled using data ready interrupts
* FIFO is emptied at 1 kHz by default, but can adjusted via IMU_GYRO_RATEMAX from 250 Hz - 2000 kHz.
* On both px4_fmu-v4 and px4_fmu-v4pro the secondary IMU is an mpu9250 with the same driver
- checked register mechanism and simple watchdog
- driver checks for errors gradually and can reconfigure itself
- respect IMU_GYRO_RATEMAX at the driver level
- fixed sensor INT16_MIN and INT16_MAX handling (y & z axis are flipped before publishing)
- checked register mechanism and simple watchdog
- driver checks for errors gradually and can reconfigure itself
- respect IMU_GYRO_RATEMAX at the driver level
- fixed sensor INT16_MIN and INT16_MAX handling (y & z axis are flipped before publishing)
- increased sensor_gyro_fifo max size (enables running the driver much slower, but still transferring all raw data)
- PX4Accelerometer/PX4Gyroscope remove unnecessary memsets
SalimTerryLi
Daniel Agar
Julian Kent
Beat Küng
mcsauder
Julian Oes