- at start perform full sensor signal path reset and wait for max time
- issue full sensor reset on any error
- only allocate DRDY perf counter if GPIO is available
- allow running faster than accel ODR (safe limit of 2 kHz in place)
- perform full sensor signal path reset and wait for max time (100 ms)
- issue full sensor reset on any error
- always read FIFO count before transfersj
- only allocate drdy perf counter if GPIO is available
- perform full sensor signal path reset and wait for max time (100 ms)
- issue full sensor reset on any error
- always read FIFO count before transfersj
- only allocate drdy perf counter if GPIO is available
- ecl in PX4/Firmware (d4fcf77c546c31c4c0b813e5034c66581b3b2877): c91c78dcf6
- ecl current upstream: b3dc06d0cb
- Changes: c91c78dcf6...b3dc06d0cbb3dc06d 2020-05-25 Roman Bapst - Added height above ground source bitmask indicating which sensor is used
62e15cb 2020-06-03 bresch - sensor_simulator: set IMU rate to 200Hz as this is the new value used in the Firmware
6126c19 2020-06-03 bresch - sensor_simulator: update EKF at IMU rate
59183f7 2020-06-02 Paul Riseborough - EKF: Reduce EKF-GSF vulnerability to large yaw gyro bias errors (#831)
d0ddda8 2020-05-29 Matthias Grob - tecs: fix typo init(i)alized
86fc94b 2020-05-24 Kamil Ritz - Remove tilt align from position innovation check
b024cdd 2020-05-25 Mathieu Bresciani - unit test: check that the accel bias is only learned when observable (#827)
Greatly improves the noise on the d-term on a Kopis 2. Apparently the order
of filtering vs differentiating matters.
Also disables the DGYRO filter by default, as the D-term now already has
a default filter of 30Hz applied.
It cause bad transfers on a Kopis 2, though not on a bench KakuteF7 unit.
Not sure if this is a single case.
nsh> icm20689 status
INFO [SPI_I2C] Running on SPI Bus 4
INFO [icm20689] FIFO empty interval: 1000 us (1000.000 Hz)
icm20689: transfer: 46375 events, 6790549us elapsed, 146.43us avg, min 54us max 1709us 81.564us rms
icm20689: bad register: 0 events
icm20689: bad transfer: 4284 events
icm20689: FIFO empty: 0 events
icm20689: FIFO overflow: 1 events
icm20689: FIFO reset: 2 events
icm20689: DRDY interval: 375585 events, 124.93us avg, min 99us max 250us 2.322us rms
INFO [drivers_accelerometer] /dev/accel device instance: 0
INFO [drivers_accelerometer] calibration scale: 1.02174 0.99918 0.98338
INFO [drivers_accelerometer] calibration offset: 0.76124 -0.00725 -0.16437
INFO [drivers_gyroscope] /dev/gyro device instance: 0
INFO [drivers_gyroscope] calibration offset: -0.08153 0.02432 0.00050
I think we can just directly use send() and don't need to use the
workaround of resetting the send flag to trigger one send.
Also, we don't need to override it if we don't need to check any params.
Instead of creating the stream and deleting it again, we now create it
with a rate of 0 and trigger it once.
This should avoid heap fragmentation by continous allocations.
Matthias Grob
Daniel Agar
RomanBapst
David Sidrane
PX4 BuildBot
Beat Küng
Mirko Denecke
Julian Oes
David Jablonski