- include icm20948 on most boards by default
- create more test variants for default boards near flash limit (cuav_nora_test, cuav_x7pro_test, holybro_durandal-v1_test)
- new IMU driver structure with state machine (no sleeps in bus thread)
- verify all configured registers and trigger reset on failure
- detect if DIO1 or DIO2 are actually connected for data ready interrupt usage
- don't use CRC-16 on burst transfers except for verified lots
This system command will display, set and save the network
settings.
netman show - Displays the current settings.
netman update - Will check for a net.cfg file on the SD card.
If present, it will update the paramaters,
delete the file, and reboot. Using the new settings.
netman save - Saves the current settings to net.cfg on the SD card.
This file shoulf be renamed to preserver it across
reboots or editited to chech networkin paramates.
File format is name<space>value:
echo DEVICE=eth0 > /fs/microsd/net.cfg
echo BOOTPROTO=fallback >> /fs/microsd/net.cfg
echo IPADDR=192.168.0.4 >> /fs/microsd/net.cfg
echo NETMASK=255.255.255.0 >>/fs/microsd/net.cfg
echo ROUTER=192.168.0.254 >>/fs/microsd/net.cfg
echo DNS=192.168.0.254 >>/fs/microsd/net.cfg
Valid values for `proto` are `dhcp`, `static`, `falback`
Both will try dhcp for CONFIG_NETINIT_FALLBACK times
and fall back to the static address.
NETMASK - is the network mask.
IPADDR - this nodes ip address for static or fall back.
ROUTER - The default route.
DNS - The address of the dns server.
* Add basic GPIO test app for R/W on pins from nuttx shell
* Add gpio command to fmu-v3 and fmu-v4
* Sanitize gpio commands by pin configs, --force to override
- always check with state machine before reboot/shutdown
- respect BOARD_HAS_POWER_CONTROL (shutdown from command, low battery, power button)
- px4_shutdown_request add optional delay and always execute from HPWORK
- px4_shutdown_request split out px4_reboot_request
* MC_HTE: unitialize with hover_thrust parameter
* MC_HTE: constrain hover thrust setter between 0.1 and 0.9
* MC_HTE: integrate with land detector and velocity controller
* MCHoverThrustEstimator: Always publish an estimate even when not fusing measurements. This is required as the land detector and the position controller need to receive a hover thrust value.
* MC_HTE: use altitude agl threshold to start the estimator
local_position.z is relative to the origin of the EKF while dist_bottom
is above ground
Co-authored-by: bresch <brescianimathieu@gmail.com>
- this is a new module for temperature compensation that consolidates the functionality previously handled in the sensors module (calculating runtime thermal corrections) and the events module (online thermal calibration)
- by collecting this functionality into a single module we can optionally disable it on systems where it's not used and save some flash (if disabled at build time) or memory (disabled at run time)
* adds a work_queue systemcmd that will bring a tree view of all active work queues and work items
* WorkQueues now track attached WorkItems and will shutdown when the last WorkItem is detached
This new airspeed module does:
-runns an airspeed validator for every airspeed sensor present, which checks measurement validity and estimates an airspeed scale
-selects another airspeed sensor if for the current one a failure is detected
-estimates airspeed with groundspeed-windspeed if no valid airspeed sensor is present
-outputs airspeed_validated topic
Signed-off-by: Silvan Fuhrer <silvan@auterion.com>
Daniel Agar
garfieldG
Beat Küng
David Sidrane
Matthias Grob
SalimTerryLi
Tanja Baumann
Julian Kent
Julian Oes
Roman Dvořák
Claudio Micheli
BazookaJoe1900
Silvan Fuhrer