- include icm20948 on most boards by default
- create more test variants for default boards near flash limit (cuav_nora_test, cuav_x7pro_test, holybro_durandal-v1_test)
- new IMU driver structure with state machine (no sleeps in bus thread)
- verify all configured registers and trigger reset on failure
- detect if DIO1 or DIO2 are actually connected for data ready interrupt usage
- don't use CRC-16 on burst transfers except for verified lots
* Commit for the Integration of a position controller for the a Underwater vehicle.
This module is an extension of the uuv_att_control to control an Underwater vehicle to any position, given by the SET_POSITION_TARGET_LOCAL_NED which includes x y z yaw.
Since the position control is designed for a 6DOF Robot, the roll and pitch angle are controlled to be 0.
Additionally there is a stabilization control, which holds the robot at a defined depth, and not move in any direction.
In general the idea is to have this position module to control the position of the uuv. The position module reseives the desired position of the uuv and sends appropriate attitude setpoints to the uuv_attitude_control module.
Additionally the mixer file is adapted, to include the 6 different inputs(x y z roll pitch yaw).
* Commit for the Integration of a position controller for the a Underwater vehicle.
This module is an extension of the uuv_att_control to control an Underwater vehicle to any position, given by the SET_POSITION_TARGET_LOCAL_NED which includes x y z yaw.
Since the position control is designed for a 6DOF Robot, the roll and pitch angle are controlled to be 0.
Additionally there is a stabilization control, which holds the robot at a defined depth, and not move in any direction.
In general the idea is to have this position module to control the position of the uuv. The position module receives the desired position of the uuv and sends appropriate attitude setpoints to the uuv_attitude_control module.
Additionally the mixer file is adapted, to include the 6 different inputs(x y z roll pitch yaw).
Currently not solved/missing:
- Problem with gazebo model(propeller moving chaotically).
- Mixer correct gazebo vs real life (has to be tested in the future)
- correct integration in uuv.apps (when choose which module)
- very basic controller chosen (could be improved a lot in the future)
* Remove error caused by unused variables and a different build error
* added better description of the parameter. Additionally the group is changed.
* added better description of the parameter. Additionally the group is changed.
Fixed bug about parameter
* Added EOF to the files.
* Removed parameter for direct position control for safety reasons.
* small bugfix
- currently the main change is that it reduces the max number of ORB multi instances to 4, but usage will be expanded as needed
- limits number of EKF2 multi instances to 2.
- enabled on all cortex m4 boards
* Add basic GPIO test app for R/W on pins from nuttx shell
* Add gpio command to fmu-v3 and fmu-v4
* Sanitize gpio commands by pin configs, --force to override
- always check with state machine before reboot/shutdown
- respect BOARD_HAS_POWER_CONTROL (shutdown from command, low battery, power button)
- px4_shutdown_request add optional delay and always execute from HPWORK
- px4_shutdown_request split out px4_reboot_request
This is another new InvenSense sensor with max output data rate of 32 kHz (both accel & gyro), on board anti-aliasing filter, and accel range 32G. Overall quite similar to the ICM-42688-P added in #14420, but with doubled accel range and without the optional high resolution output or clock sync.
* MC_HTE: unitialize with hover_thrust parameter
* MC_HTE: constrain hover thrust setter between 0.1 and 0.9
* MC_HTE: integrate with land detector and velocity controller
* MCHoverThrustEstimator: Always publish an estimate even when not fusing measurements. This is required as the land detector and the position controller need to receive a hover thrust value.
* MC_HTE: use altitude agl threshold to start the estimator
local_position.z is relative to the origin of the EKF while dist_bottom
is above ground
Co-authored-by: bresch <brescianimathieu@gmail.com>
* 8 kHz gyro, 4 kHz accel
* DLPF disabled
* scheduled using data ready interrupts
* FIFO is emptied at 1 kHz by default, but can adjusted via IMU_GYRO_RATEMAX from 250 Hz - 2000 kHz.
* On both px4_fmu-v4 and px4_fmu-v4pro the secondary IMU is an mpu9250 with the same driver
- checked register mechanism and simple watchdog
- driver checks for errors gradually and can reconfigure itself
- respect IMU_GYRO_RATEMAX at the driver level
- fixed sensor INT16_MIN and INT16_MAX handling (y & z axis are flipped before publishing)
- checked register mechanism and simple watchdog
- driver checks for errors gradually and can reconfigure itself
- respect IMU_GYRO_RATEMAX at the driver level
- fixed sensor INT16_MIN and INT16_MAX handling (y & z axis are flipped before publishing)
- increased sensor_gyro_fifo max size (enables running the driver much slower, but still transferring all raw data)
- PX4Accelerometer/PX4Gyroscope remove unnecessary memsets
* add support for unmanned underwater vehicles:
* airframe uuv_generic + uuv_hippocammpus including mav_type = 12 for submarines
* mixer for UUVs with X-shaped thruster setup similar to quadcopter
* add module uuv_att_control for underwater robot attitude control
* add rc.uuv_defaults/apps for autostarting e.g. ekf2 and uuv_att_control app
- this is a new module for temperature compensation that consolidates the functionality previously handled in the sensors module (calculating runtime thermal corrections) and the events module (online thermal calibration)
- by collecting this functionality into a single module we can optionally disable it on systems where it's not used and save some flash (if disabled at build time) or memory (disabled at run time)
- uses the FIFO and SPI DMA to transfer full raw data (8 kHz gyro, 4 kHz accel)
- new sensor messages for better visibility
- sensor_{accel, gyro}_fifo: full raw data for optional logging and analysis
- sensor_{accel, gyro}_status: metadata, clipping, etc
- currently not enabled by default
Beat Küng
echoG
Daniel Agar
Tim
Peter van der Perk
Nicolas de Palezieux
Matthias Grob
David Sidrane
SalimTerryLi
Tanja Baumann
Julian Kent
Julian Oes
Daniel Duecker
Igor Mišić