uorb start
param load
param set MAV_TYPE 2
param set MC_PITCHRATE_P 0.15
param set MC_ROLLRATE_P 0.15
param set MC_YAW_P 2.0
param set MC_YAWRATE_P 0.35
param set SYS_AUTOSTART 4010
param set SYS_RESTART_TYPE 2
param set SYS_MC_EST_GROUP 0
dataman start
param set CAL_GYRO0_ID 2293768
param set CAL_ACC0_ID 1376264
param set CAL_ACC1_ID 1310728
param set CAL_MAG0_ID 196616
param set CAL_GYRO0_XOFF 0.01
param set CAL_ACC0_XOFF 0.01
param set CAL_ACC0_YOFF -0.01
param set CAL_ACC0_ZOFF 0.01
param set CAL_ACC0_XSCALE 1.01
param set CAL_ACC0_YSCALE 1.01
param set CAL_ACC0_ZSCALE 1.01
param set CAL_ACC1_XOFF 0.01
param set CAL_MAG0_XOFF 0.01
param set MPC_XY_P 0.4
param set MPC_XY_VEL_P 0.2
param set MPC_XY_VEL_D 0.005
param set MPP_XY_P 1.0
param set MPP_XY_FF 0.0
param set MPP_XY_VEL_P 0.01
param set MPP_XY_VEL_I 0.0
param set MPP_XY_VEL_D 0.01
param set MPP_XY_VEL_MAX 2.0
param set MPP_Z_VEL_P 0.3
param set MPP_Z_P 2
param set SENS_BOARD_ROT 0
param set SENS_BOARD_X_OFF 0.000001
param set MP_ROLL_P 3
param set MP_ROLLRATE_P 0.3
param set MP_ROLLRATE_I 0.001
param set MP_ROLLRATE_D 0.001
param set MP_PITCH_P 4
param set MP_PITCHRATE_P 0.3
param set COM_RC_IN_MODE 1
param set NAV_DLL_ACT 2
replay tryapplyparams
simulator start -s
tone_alarm start
gyrosim start
accelsim start
barosim start
adcsim start
gpssim start
pwm_out_sim mode_pwm
sensors start
commander start
land_detector start multicopter
navigator start
attitude_estimator_q start
position_estimator_inav start
mc_pos_control_m start
mc_att_control_m start
mixer load /dev/pwm_output0 ROMFS/px4fmu_common/mixers/quad_x.main.mix
mavlink start -u 14556 -r 2000000
mavlink stream -r 50 -s POSITION_TARGET_LOCAL_NED -u 14556
mavlink stream -r 50 -s LOCAL_POSITION_NED -u 14556
mavlink stream -r 50 -s GLOBAL_POSITION_INT -u 14556
mavlink stream -r 50 -s ATTITUDE -u 14556
mavlink stream -r 50 -s ATTITUDE_QUATERNION -u 14556
mavlink stream -r 50 -s ATTITUDE_TARGET -u 14556
mavlink stream -r 50 -s SERVO_OUTPUT_RAW_0 -u 14556
mavlink stream -r 20 -s RC_CHANNELS -u 14556
mavlink stream -r 250 -s HIGHRES_IMU -u 14556
mavlink stream -r 10 -s OPTICAL_FLOW_RAD -u 14556
logger start -e -t
mavlink boot_complete
replay trystart