You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
95 lines
2.1 KiB
95 lines
2.1 KiB
# |
|
# For a description of the syntax of this configuration file, |
|
# see misc/tools/kconfig-language.txt. |
|
# |
|
config NET_DM90x0 |
|
bool "Davicom dm9000/dm9010 support" |
|
default n |
|
---help--- |
|
References: Davicom data sheets (DM9000-DS-F03-041906.pdf, |
|
DM9010-DS-F01-103006.pdf) and looking at lots of other DM90x0 |
|
drivers. |
|
|
|
config NET_CS89x0 |
|
bool "CS89x0 support" |
|
default n |
|
depends on EXPERIMENTAL |
|
---help--- |
|
Under construction -- do not use |
|
|
|
config ENC28J60 |
|
bool "Microchip ENC28J60 support" |
|
default n |
|
select SPI |
|
---help--- |
|
References: |
|
ENC28J60 Data Sheet, Stand-Alone Ethernet Controller with SPI Interface, |
|
DS39662C, 2008 Microchip Technology Inc. |
|
|
|
if ENC28J60 |
|
config ENC28J60_NINTERFACES |
|
int "Number of physical ENC28J60" |
|
default 1 |
|
range 1,1 |
|
---help--- |
|
Specifies the number of physical ENC28J60 |
|
devices that will be supported. |
|
|
|
config ENC28J60_SPIMODE |
|
int "SPI mode" |
|
default 0 |
|
---help--- |
|
Controls the SPI mode. The ENC28J60 spec says that it supports SPI |
|
mode 0,0 only: "The implementation used on this device supports SPI |
|
mode 0,0 only. In addition, the SPI port requires that SCK be at Idle |
|
in a low state; selectable clock polarity is not supported." |
|
However, sometimes you need to tinker with these things. |
|
|
|
config ENC28J60_FREQUENCY |
|
int "SPI frequency" |
|
default 20000000 |
|
---help--- |
|
Define to use a different bus frequency |
|
|
|
config ENC28J60_STATS |
|
bool "Network statistics support" |
|
default n |
|
---help--- |
|
Collect network statistics |
|
|
|
config ENC28J60_HALFDUPPLEX |
|
bool "Enable half dupplex" |
|
default n |
|
---help--- |
|
Default is full duplex |
|
|
|
config ENC28J60_DUMPPACKET |
|
bool "Dump Packets" |
|
default n |
|
---help--- |
|
If selected, the ENC28J60 driver will dump the contents of each |
|
packet to the console. |
|
|
|
config ENC28J60_REGDEBUG |
|
bool "Register-Level Debug" |
|
default n |
|
depends on DEBUG && DEBUG_NET |
|
---help--- |
|
Enable very low-level register access debug. Depends on DEBUG and DEBUG_NET. |
|
|
|
endif |
|
|
|
config NET_E1000 |
|
bool "E1000 support" |
|
default n |
|
|
|
config NET_SLIP |
|
bool "SLIP (serial line) support" |
|
default n |
|
---help--- |
|
Reference: RFC 1055 |
|
|
|
config NET_VNET |
|
bool "VNET support" |
|
default n |
|
|
|
|