You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
105 lines
2.7 KiB
105 lines
2.7 KiB
#!/bin/sh |
|
# |
|
# board specific defaults |
|
#------------------------------------------------------------------------------ |
|
|
|
# |
|
# Summary: |
|
# Flight Core can be used on many airframes, but is meant to be paired with |
|
# VOXL (either through a cable or in the combo board flavor). For this reason |
|
# this script has a bit more Logic (aka Bobby Tarantino) than normal. |
|
# |
|
# Flight Core Version Information: |
|
# V106 - Flight Core Stand Alone configuration |
|
# V110 - Flight Core VOXL-Flight configuration |
|
# |
|
|
|
# |
|
# Common settings across Flight Core configurations |
|
# |
|
|
|
# Disable safety switch by default (pull high to 3.3V to enable) |
|
# V106 - J13 pin 5 |
|
# V110 - J1011 pin 5 |
|
param set-default CBRK_IO_SAFETY 22027 |
|
|
|
# |
|
# Stand Alone configuration |
|
# |
|
if ver hwtypecmp V106 |
|
then |
|
echo "Configuring Flight Core - V106" |
|
|
|
# |
|
# In Flight Core, J1 can be setup to be used as a serial port for TELEM2 |
|
# and connected to VOXL via cables. We'll configure this out of the box. |
|
# The user can later change this if they want, as these are configurable |
|
# and not necessarily required to be used with VOXL. |
|
# |
|
if [ $AUTOCNF = no ] |
|
then |
|
if param compare MAV_1_CONFIG 0 |
|
then |
|
echo "V106 - Defualt configuration TELEM2 on /dev/ttyS4 at 921600 in Normal Mode" |
|
# TELEM2 |
|
param set-default MAV_1_CONFIG 102 |
|
# Onboard |
|
param set-default MAV_1_MODE 2 |
|
# VIO data |
|
param set-default SER_TEL2_BAUD 921600 |
|
fi |
|
fi |
|
|
|
# User is setting defaults, so let's do it! |
|
if [ $AUTOCNF = yes ] |
|
then |
|
echo "V106 - Auto Configuring TELEM2 on /dev/ttyS4 at 921600 in Normal Mode" |
|
# TELEM2 |
|
param set-default MAV_1_CONFIG 102 |
|
# Onboard |
|
param set-default MAV_1_MODE 2 |
|
# VIO data |
|
param set-default SER_TEL2_BAUD 921600 |
|
fi |
|
fi |
|
|
|
# |
|
# VOXL-Flight configuration |
|
# |
|
if ver hwtypecmp V110 |
|
then |
|
echo "Configuring VOXL-Flight - V110" |
|
|
|
# |
|
# TELEM2 port is physically routed in the PCB, thus not configurable. |
|
# The following will detect a fresh install, or if the user has changed the setting and |
|
# revert to the VOXL-Flight defaults. This does allow the user to change the mode and |
|
# baud rates and mode if they choose to do so, although VOXL is expecting what is set below |
|
# |
|
if [ $AUTOCNF = no ] |
|
then |
|
if ! param compare MAV_1_CONFIG 102 |
|
then |
|
echo "V110 - Default configuration TELEM2 on /dev/ttyS4 at 921600 in Normal Mode" |
|
# TELEM2 |
|
param set-default MAV_1_CONFIG 102 |
|
# Onboard |
|
param set-default MAV_1_MODE 2 |
|
param set-default SER_TEL2_BAUD 921600 |
|
fi |
|
fi |
|
|
|
# User is setting defaults, so let's do it! |
|
if [ $AUTOCNF = yes ] |
|
then |
|
echo "V110 - Auto Configuring TELEM2 on /dev/ttyS4 at 921600 in Normal Mode" |
|
# TELEM2 |
|
param set-default MAV_1_CONFIG 102 |
|
# Onboard |
|
param set-default MAV_1_MODE 2 |
|
param set-default SER_TEL2_BAUD 921600 |
|
fi |
|
fi |
|
|
|
|
|
safety_button start
|
|
|