LukeMike
6 years ago
committed by
Andrew Tridgell
2 changed files with 227 additions and 0 deletions
@ -0,0 +1,61 @@
@@ -0,0 +1,61 @@
|
||||
# hw definition file for processing by chibios_hwdef.py |
||||
# for VRBRAINv52 hardware |
||||
|
||||
|
||||
# MCU class and specific type |
||||
MCU STM32F4xx STM32F407xx |
||||
|
||||
# board ID for firmware load |
||||
APJ_BOARD_ID 1152 |
||||
|
||||
# crystal frequency |
||||
OSCILLATOR_HZ 8000000 |
||||
STM32_PLLM_VALUE 8 |
||||
|
||||
# flash size |
||||
FLASH_SIZE_KB 1024 |
||||
|
||||
# board voltage |
||||
STM32_VDD 330U |
||||
|
||||
# USB setup |
||||
USB_VENDOR 0x27AC |
||||
USB_PRODUCT 0x1151 |
||||
USB_STRING_MANUFACTURER "Laser Navigation" |
||||
USB_STRING_SERIAL "%SERIAL%" |
||||
|
||||
# don't allow bootloader to use more than 16k |
||||
FLASH_USE_MAX_KB 16 |
||||
|
||||
# bootloader is installed at zero offset |
||||
FLASH_RESERVE_START_KB 0 |
||||
|
||||
# the location where the bootloader will put the firmware |
||||
define FLASH_BOOTLOADER_LOAD_KB 16 |
||||
|
||||
# ChibiOS system timer |
||||
STM32_ST_USE_TIMER 5 |
||||
|
||||
|
||||
# order of UARTs (and USB) |
||||
UART_ORDER OTG1 |
||||
|
||||
PA9 VBUS INPUT |
||||
|
||||
PA11 OTG_FS_DM OTG1 |
||||
PA12 OTG_FS_DP OTG1 |
||||
|
||||
PA13 JTMS-SWDIO SWD |
||||
PA14 JTCK-SWCLK SWD |
||||
|
||||
PD14 LED_BOOTLOADER OUTPUT |
||||
PC5 LED_ACTIVITY OUTPUT |
||||
|
||||
define HAL_LED_ON 0 |
||||
|
||||
define HAL_CHIBIOS_ARCH_BRAINV52 1 |
||||
|
||||
define HAL_STORAGE_SIZE 16384 |
||||
define HAL_USE_EMPTY_STORAGE 1 |
||||
|
||||
|
||||
@ -0,0 +1,166 @@
@@ -0,0 +1,166 @@
|
||||
# hw definition file for processing by chibios_hwdef.py |
||||
# for VRBRAINv52 hardware |
||||
|
||||
define CONFIG_HAL_BOARD_SUBTYPE HAL_BOARD_SUBTYPE_CHIBIOS_VRBRAIN_V52 |
||||
|
||||
# MCU class and specific type |
||||
MCU STM32F4xx STM32F407xx |
||||
|
||||
# board ID for firmware load |
||||
APJ_BOARD_ID 1152 |
||||
|
||||
# crystal frequency |
||||
OSCILLATOR_HZ 8000000 |
||||
STM32_PLLM_VALUE 8 |
||||
|
||||
# flash size |
||||
FLASH_SIZE_KB 1024 |
||||
|
||||
# board voltage |
||||
STM32_VDD 330U |
||||
|
||||
# USB setup |
||||
USB_VENDOR 0x27AC |
||||
USB_PRODUCT 0x1151 |
||||
USB_STRING_MANUFACTURER "Laser Navigation" |
||||
USB_STRING_SERIAL "%SERIAL%" |
||||
|
||||
# ChibiOS system timer |
||||
STM32_ST_USE_TIMER 5 |
||||
|
||||
# only one I2C bus |
||||
I2C_ORDER I2C2 I2C1 |
||||
|
||||
# order of UARTs (and USB) |
||||
UART_ORDER OTG1 USART1 USART3 USART2 |
||||
STDOUT_SERIAL SD3 |
||||
STDOUT_BAUDRATE 57600 |
||||
|
||||
|
||||
#PA0 TIM2_CH1 TIM2 GPIO(77) ALARM # OUT_CH1 |
||||
PA1 TIM2_CH2 TIM2 PWM(1) GPIO(50) # PWM_CH0 |
||||
PA2 TIM2_CH3 TIM2 PWM(2) GPIO(51) # PWM_CH1 |
||||
PA3 TIM2_CH4 TIM2 PWM(3) GPIO(52) # PWM_CH2 |
||||
PA4 SDCARD_CS CS # CS_SDCARD |
||||
PA5 SPI1_SCK SPI1 # SPI1_SCK |
||||
PA6 SPI1_MISO SPI1 # SPI1_MISO |
||||
PA7 SPI1_MOSI SPI1 # SPI1_MOSI |
||||
#PA8 # EXP_GIRO_EN |
||||
PA9 VBUS INPUT # USB_VBUS |
||||
#P10 # USB_ID |
||||
PA11 OTG_FS_DM OTG1 # USBM |
||||
PA12 OTG_FS_DP OTG1 # USBP |
||||
PA13 JTMS-SWDIO SWD # JTAG_TMS |
||||
PA14 JTCK-SWCLK SWD # JTAG_TCK |
||||
#PA15 # Not connected |
||||
|
||||
PB0 TIM3_CH3 TIM3 PWM(5) GPIO(54) # PWM_CH4 |
||||
PB1 TIM3_CH4 TIM3 PWM(6) GPIO(55) # PWM_CH5 |
||||
#PB2 |
||||
PB3 LED_EXT3 OUTPUT GPIO(5) # Not connected |
||||
PB4 LED_EXT4 OUTPUT GPIO(6) # Not connected |
||||
PB5 TIM3_CH2 TIM3 PWM(4) GPIO(53) # PWM_CH3 |
||||
PB6 USART1_TX USART1 # UART1_TX |
||||
PB7 USART1_RX USART1 # UART1_RX |
||||
PB8 I2C1_SCL I2C1 # SCL2/CANRX |
||||
PB9 I2C1_SDA I2C1 # SDA2/CANTX |
||||
PB10 I2C2_SCL I2C2 # SCL |
||||
PB11 I2C2_SDA I2C2 # SDA |
||||
#PB12 # INT_MAG |
||||
PB13 SPI2_SCK SPI2 # SPI2_SCK |
||||
PB14 SPI2_MISO SPI2 # SPI2_MISO |
||||
PB15 SPI2_MOSI SPI2 # SPI2_MOSI |
||||
|
||||
PC0 BATT_VOLTAGE_SENS ADC1 # ADC12_VBAT |
||||
PC1 BATT_CURRENT_SENS ADC1 # ADC12_IBAT |
||||
#PC2 # CS_GYRO_IMU |
||||
#PC3 # CS_MAG_IMU |
||||
#PC4 # SONAR_IN |
||||
PC5 LED_GREEN OUTPUT GPIO(1) # CMD_LED_RED |
||||
#PC6 # SBUS_TX |
||||
PC7 TIM8_CH2 TIM8 RCIN FLOAT LOW # SBUS_RX |
||||
#PC8 |
||||
#PC9 |
||||
PC10 SPI3_SCK SPI3 # SPI3_SCK |
||||
PC11 SPI3_MISO SPI3 # SPI3_MISO |
||||
PC12 SPI3_MOSI SPI3 # SPI3_MOSI |
||||
#PC13 # Not connected |
||||
#PC14 # INT_GYRO_IMU |
||||
#PC15 # INT_MAG_IMU |
||||
|
||||
#PD0 # SIG_CAN_RX |
||||
#PD1 # SIG_CAN_TX |
||||
#PD2 # CS_EEPROM_IMU |
||||
#PD3 # EXP_INT_GYRO |
||||
#PD4 # UART3_CTS |
||||
PD5 USART2_TX USART2 # UART2_TX |
||||
PD6 USART2_RX USART2 # UART2_RX |
||||
PD7 SBUS_INV OUTPUT # SBUS_EN |
||||
PD8 USART3_TX USART3 # UART3_TX |
||||
PD9 USART3_RX USART3 # UART3_RX |
||||
#PD10 # NT_GYRO |
||||
#PD11 # UART3_RTS |
||||
PD12 TIM4_CH1 TIM4 PWM(8) GPIO(57) # PWM_CH7 |
||||
PD13 TIM4_CH2 TIM4 PWM(7) GPIO(56) # PWM_CH6 |
||||
PD15 LED_RED OUTPUT GPIO(0) # CMD_LED_GRN |
||||
PD14 LED_BLUE OUTPUT GPIO(2) # CMD_LED_BLU |
||||
|
||||
PE0 BARO_CS CS # CS_BARO |
||||
#PE1 # EXP_EEPROM_WIFI_CS |
||||
#PE2 LED_EXT1 OUTPUT GPIO(3) # OUT_CH3 |
||||
#PE3 LED_EXT2 OUTPUT GPIO(4) # OUT_CH2 |
||||
#PE4 # OUT_CH0 |
||||
#PE5 # PWM_IN4 |
||||
#PE6 # PWM_IN5 |
||||
#PE7 # EXP_WIFI_EN |
||||
#PE8 # EXP_WIFI_INT |
||||
PE9 TIM1_CH1 TIM1 PWM(9) GPIO(58) # PWM_CH8 |
||||
PE10 MPU_CS CS # CS_GYRO |
||||
PE11 TIM1_CH2 TIM1 PWM(10) GPIO(59) # PWM_CH9 |
||||
PE13 TIM1_CH3 TIM1 PWM(11) GPIO(60) # PWM_CH10 |
||||
PE14 TIM1_CH4 TIM1 PWM(12) GPIO(61) # PWM_CH11 |
||||
PE15 FRAM_CS CS # CS_EEPROM |
||||
|
||||
# SPI device table. The DEVID values are chosen to match the PX4 port |
||||
# of ArduPilot so users don't need to re-do their accel and compass calibrations |
||||
# when moving to ChibiOS |
||||
SPIDEV ms5611 SPI1 DEVID3 BARO_CS MODE3 20*MHZ 20*MHZ |
||||
SPIDEV mpu6000 SPI2 DEVID4 MPU_CS MODE3 2*MHZ 8*MHZ |
||||
SPIDEV ramtron SPI3 DEVID10 FRAM_CS MODE3 8*MHZ 8*MHZ |
||||
SPIDEV sdcard SPI3 DEVID1 SDCARD_CS MODE0 400*KHZ 25*MHZ |
||||
|
||||
define HAL_CHIBIOS_ARCH_BRAINV52 1 |
||||
|
||||
define HAL_BOARD_LOG_DIRECTORY "/APM/LOGS" |
||||
define HAL_BOARD_TERRAIN_DIRECTORY "/APM/TERRAIN" |
||||
|
||||
define HAL_STORAGE_SIZE 16384 |
||||
define STORAGE_FLASH_PAGE 22 |
||||
|
||||
# enable RAMTROM parameter storage |
||||
define HAL_WITH_RAMTRON 1 |
||||
|
||||
# enable FAT filesystem |
||||
define HAL_OS_FATFS_IO 1 |
||||
|
||||
define HAL_GPIO_LED_ON 0 |
||||
define HAL_GPIO_LED_OFF 1 |
||||
|
||||
define HAL_GPIO_A_LED_PIN 2 |
||||
define HAL_GPIO_B_LED_PIN 1 |
||||
define HAL_GPIO_C_LED_PIN 0 |
||||
|
||||
define EXTERNAL_LED_ARMED 3 |
||||
define EXTERNAL_LED_GPS 4 |
||||
define EXTERNAL_LED_MOTOR1 5 |
||||
define EXTERNAL_LED_MOTOR2 6 |
||||
|
||||
# battery setup |
||||
define HAL_BATT_VOLT_PIN 2 |
||||
define HAL_BATT_CURR_PIN 3 |
||||
define HAL_BATT_VOLT_SCALE 10.1 |
||||
define HAL_BATT_CURR_SCALE 17.0 |
||||
|
||||
# 12 PWM available by default |
||||
define BOARD_PWM_COUNT_DEFAULT 12 |
||||
|
||||
Loading…
Reference in new issue