2.0.12 Very small Yaw Iterm added. reverted to earlier Loiter limit.

Slight tweak to Alt hold.


git-svn-id: https://arducopter.googlecode.com/svn/trunk@2397 f9c3cf11-9bcb-44bc-f272-b75c42450872

ArduCopterMega/ArduCopterMega.pde

@@ -763,7 +763,7 @@ void slow_loop()
 			slow_loopCounter++;
 			superslow_loopCounter++;
 
-			if(superslow_loopCounter > 1400){ // every 7 minutes
+			if(superslow_loopCounter > 800){ // every 4 minutes
 				#if HIL_MODE != HIL_MODE_ATTITUDE
 					if(g.rc_3.control_in == 0 && g.compass_enabled){
 						compass.save_offsets();

ArduCopterMega/config.h

@@ -61,6 +61,7 @@
 # define SONAR_PIN		AP_RANGEFINDER_PITOT_TUBE
 #endif
 
+
 //////////////////////////////////////////////////////////////////////////////
 // AIRSPEED_SENSOR
 // AIRSPEED_RATIO
@@ -72,6 +73,7 @@
 # define AIRSPEED_RATIO			1.9936		// Note - this varies from the value in ArduPilot due to the difference in ADC resolution
 #endif
 
+
 //////////////////////////////////////////////////////////////////////////////
 // HIL_PROTOCOL                             OPTIONAL
 // HIL_MODE                                 OPTIONAL
@@ -114,6 +116,7 @@
  #endif
 #endif
 
+
 //////////////////////////////////////////////////////////////////////////////
 // GPS_PROTOCOL
 //
@@ -124,6 +127,7 @@
 # define GPS_PROTOCOL 		GPS_PROTOCOL_AUTO
 #endif
 
+
 //////////////////////////////////////////////////////////////////////////////
 // GCS_PROTOCOL
 // GCS_PORT
@@ -141,6 +145,7 @@
 # define MAV_SYSTEM_ID		1
 #endif
 
+
 //////////////////////////////////////////////////////////////////////////////
 // Serial port speeds.
 //
@@ -175,6 +180,7 @@
 # define HIGH_DISCHARGE		1760
 #endif
 
+
 //////////////////////////////////////////////////////////////////////////////
 // INPUT_VOLTAGE
 //
@@ -182,6 +188,7 @@
 # define INPUT_VOLTAGE			5.0
 #endif
 
+
 //////////////////////////////////////////////////////////////////////////////
 //  MAGNETOMETER
 #ifndef MAGNETOMETER
@@ -280,7 +287,7 @@
 # define ACRO_RATE_ROLL_D         0.0
 #endif
 #ifndef ACRO_RATE_ROLL_IMAX
-# define ACRO_RATE_ROLL_IMAX	 20
+# define ACRO_RATE_ROLL_IMAX	 	20
 #endif
 
 #ifndef ACRO_RATE_PITCH_P
@@ -293,7 +300,7 @@
 # define ACRO_RATE_PITCH_D         0.0
 #endif
 #ifndef ACRO_RATE_PITCH_IMAX
-# define ACRO_RATE_PITCH_IMAX   20
+# define ACRO_RATE_PITCH_IMAX   	20
 #endif
 
 #ifndef ACRO_RATE_YAW_P
@@ -350,13 +357,13 @@
 # define YAW_P					0.4			// increase for more aggressive Yaw Hold, decrease if it's bouncy
 #endif
 #ifndef  YAW_I
-# define YAW_I					0.000		// set to .0001 to try and get over user's steady state error caused by poor balance
+# define YAW_I					0.0001		// set to .0001 to try and get over user's steady state error caused by poor balance
 #endif
 #ifndef  YAW_D
 # define YAW_D					0.05		// Trying a lower value to prevent odd behavior
 #endif
 #ifndef  YAW_IMAX
-# define YAW_IMAX				1			// degrees * 100
+# define YAW_IMAX				.5			// degrees * 100
 #endif
 
 //////////////////////////////////////////////////////////////////////////////
@@ -375,7 +382,7 @@
 # define NAV_LOITER_P			2.5			// upped to be a bit more aggressive
 #endif
 #ifndef NAV_LOITER_I
-# define NAV_LOITER_I			0.05		// upped a bit to deal with wind faster
+# define NAV_LOITER_I			0.10		// upped a bit to deal with wind faster
 #endif
 #ifndef NAV_LOITER_D
 # define NAV_LOITER_D			0.00
@@ -412,14 +419,15 @@
 	#endif
 #endif
 
+
 //////////////////////////////////////////////////////////////////////////////
 // Throttle control gains
 //
 #ifndef THROTTLE_BARO_P
-# define THROTTLE_BARO_P		0.3
+# define THROTTLE_BARO_P		0.25
 #endif
 #ifndef THROTTLE_BARO_I
-# define THROTTLE_BARO_I		0.005
+# define THROTTLE_BARO_I		0.0045
 #endif
 #ifndef THROTTLE_BARO_D
 # define THROTTLE_BARO_D		0.03
@@ -472,6 +480,7 @@
 # define CHANNEL_6_TUNING CH6_NONE
 #endif
 
+
 //////////////////////////////////////////////////////////////////////////////
 // Dataflash logging control
 //

ArduCopterMega/system.pde

@@ -37,7 +37,7 @@ const struct Menu::command main_menu_commands[] PROGMEM = {
 };
 
 // Create the top-level menu object.
-MENU(main_menu, "AC 2.0.11 Beta", main_menu_commands);
+MENU(main_menu, "AC 2.0.12 Beta", main_menu_commands);
 
 void init_ardupilot()
 {