// @Description: This determines when the filter will use the 3-axis magnetometer fusion model that estimates both earth and body fixed magnetic field states and when it will use a simpler magnetic heading fusion model that does not use magnetic field states. The 3-axis magnetometer fusion is only suitable for use when the external magnetic field environment is stable. EK3_MAG_CAL = 0 uses heading fusion on ground, 3-axis fusion in-flight, and is the default setting for Plane users. EK3_MAG_CAL = 1 uses 3-axis fusion only when manoeuvring. EK3_MAG_CAL = 2 uses heading fusion at all times, is recommended if the external magnetic field is varying and is the default for rovers. EK3_MAG_CAL = 3 uses heading fusion on the ground and 3-axis fusion after the first in-air field and yaw reset has completed, and is the default for copters. EK3_MAG_CAL = 4 uses 3-axis fusion at all times. EK3_MAG_CAL = 5 uses an external yaw sensor with simple heading fusion. NOTE : Use of simple heading magnetometer fusion makes vehicle compass calibration and alignment errors harder for the EKF to detect which reduces the sensitivity of the Copter EKF failsafe algorithm. NOTE: The fusion mode can be forced to 2 for specific EKF cores using the EK3_MAG_MASK parameter. EK3_MAG_CAL=6 uses an external yaw sensor with fallback to compass when the external sensor is not available if we are flying. EK3_MAG_CAL = 7 aligns the yaw angle using IMU and GPS velocity data. NOTE: The fusion mode can be forced to 2 for specific EKF cores using the EK3_MAG_MASK parameter. NOTE: When using EKF3_MAG_CAL = 7, the EK3_GSF_RUN and EK3_GSF_USE masks must be set to the same as EK3_IMU_MASK and all COMPASS_USE parameters must be set to 0.
// @Values: 0:When flying,1:When manoeuvring,2:Never,3:After first climb yaw reset,4:Always,5:Use external yaw sensor,6:External yaw sensor with compass fallback,7:Use IMU and GPS velocity
// @Description: This determines when the filter will use the 3-axis magnetometer fusion model that estimates both earth and body fixed magnetic field states and when it will use a simpler magnetic heading fusion model that does not use magnetic field states. The 3-axis magnetometer fusion is only suitable for use when the external magnetic field environment is stable. EK3_MAG_CAL = 0 uses heading fusion on ground, 3-axis fusion in-flight, and is the default setting for Plane users. EK3_MAG_CAL = 1 uses 3-axis fusion only when manoeuvring. EK3_MAG_CAL = 2 uses heading fusion at all times, is recommended if the external magnetic field is varying and is the default for rovers. EK3_MAG_CAL = 3 uses heading fusion on the ground and 3-axis fusion after the first in-air field and yaw reset has completed, and is the default for copters. EK3_MAG_CAL = 4 uses 3-axis fusion at all times. EK3_MAG_CAL = 5 uses an external yaw sensor with simple heading fusion. NOTE : Use of simple heading magnetometer fusion makes vehicle compass calibration and alignment errors harder for the EKF to detect which reduces the sensitivity of the Copter EKF failsafe algorithm. NOTE: The fusion mode can be forced to 2 for specific EKF cores using the EK3_MAG_MASK parameter. EK3_MAG_CAL=6 uses an external yaw sensor with fallback to compass when the external sensor is not available if we are flying. EK3_MAG_CAL = 7 uses a yaw angle derived from IMU and GPS velocity data using a Gaussian Sum Filter (GSF). NOTE: The fusion mode can be forced to 2 for specific EKF cores using the EK3_MAG_MASK parameter. NOTE: When using EKF3_MAG_CAL = 7, the EK3_GSF_RUN and EK3_GSF_USE masks must be set to the same as EK3_IMU_MASK and COMPASS_ENABLE must be set to 0 and yaw alignment will not occur until after takeoff with sufficient horizontal movement.
// @Values: 0:When flying,1:When manoeuvring,2:Never,3:After first climb yaw reset,4:Always,5:Use external yaw sensor,6:External yaw sensor with compass fallback,7:Use GSF yaw estimate
Paul Riseborough
5 years ago
committed by
Andrew Tridgell