this resolves an edge case in which the motors could spin up on the next reboot because the user didn't unplug the battery to reboot the flight controller
Stop "latching" calibration checks - if an RC radio's calibration
changes after it passes once, these patches allow the rc calibraiton
checks to then fail.
It was possible for a board with no safety switch attached to get stuck waiting for the user to press the non-existance switch. Rebooting now resolves the problem because the ESC_CAL parameter is reset to zero regardless of whether the calibration completes or not.
The notify devices including the RGB were not being updated meaning the main LED was normally frozen or off during calibration. The desired behaviour is that it flashes red, blue, yellow.
Further to refactor of RC_Channel class which included
adding get_xx set_xx methods, change reads and writes to the public members
to calls to get and set functionsss
old public member(int16_t) get function -> int16_t set function (int16_t)
(expression where c is an object of type RC_Channel)
c.radio_in c.get_radio_in() c.set_radio_in(v)
c.control_in c.get_control_in() c.set_control_in(v)
c.servo_out c.get_servo_out() c.set_servo_out(v)
c.pwm_out c.get_pwm_out() // use existing
c.radio_out c.get_radio_out() c.set_radio_out(v)
c.radio_max c.get_radio_max() c.set_radio_max(v)
c.radio_min c.get_radio_min() c.set_radio_min(v)
c.radio_trim c.get_radio_trim() c.set_radio_trim(v);
c.min_max_configured() // return true if min and max are configured
Because data members of RC_Channels are now private and so cannot be written directly
some overloads are provided in the Plane classes to provide the old functionality
new overload Plane::stick_mix_channel(RC_Channel *channel)
which forwards to the previously existing
void stick_mix_channel(RC_Channel *channel, int16_t &servo_out);
new overload Plane::channel_output_mixer(Rc_Channel* , RC_Channel*)const
which forwards to
(uint8_t mixing_type, int16_t & chan1, int16_t & chan2)const;
Rename functions
RC_Channel_aux::set_radio_trim(Aux_servo_function_t function)
to RC_Channel_aux::set_trim_to_radio_in_for(Aux_servo_function_t function)
RC_Channel_aux::set_servo_out(Aux_servo_function_t function, int16_t value)
to RC_Channel_aux::set_servo_out_for(Aux_servo_function_t function, int16_t value)
Rationale:
RC_Channel is a complicated class, which combines
several functionalities dealing with stick inputs
in pwm and logical units, logical and actual actuator
outputs, unit conversion etc, etc
The intent of this PR is to clarify existing use of
the class. At the basic level it should now be possible
to grep all places where private variable is set by
searching for the set_xx function.
(The wider purpose is to provide a more generic and
logically simpler method of output mixing. This is a small step)
The PSTR is already define as a NOP for all supported platforms. It's
only needed for AVR so here we remove all the uses throughout the
codebase.
This was automated with a simple python script so it also converts
places which spans to multiple lines, removing the matching parentheses.
AVR-specific places were not changed.
Restructured into case statement
Replaced use of g.throttle_max with definition
Added more comments
Send message to ground station instead of printing on console (although
probably both are unlikely to be read)
zbr
yaozb
Randy Mackay
Pierre Kancir
murata
Andrew Tridgell
Peter Barker
Mathieu OTHACEHE
mirkix
skyscraper
Luis Vale Gonçalves
lvale
Lucas De Marchi
squilter
Jonathan Challinger
Jason Short