d441354961
TradHeli: Minor change to two param defaults
...
Also one param name in the code clarified.
11 years ago
782ce54a5c
TradHeli: Fix for yaw offset switching. Yaw Offset should switch on and off with the main motor, not waiting until the rotor has reached full speed.
11 years ago
343ea66cd1
Copter: add OctaQuad V frame
11 years ago
279d515e59
Copter: Y6 new motor factor fix
11 years ago
4148c4e024
TradHeli: bug fix for main rotor ramp up
...
The main rotor ramp was being held back by the rotor speed estimate
instead of being allowed to jump up to the estimate if it's lower.
Also fixed some incorrect indentation
11 years ago
8149b54807
Copter: add Y6 with all top props CW
...
Set FRAME parameter to 10
11 years ago
90937be3d4
AP_Motors: fix example sketch
11 years ago
f9e19b8006
TradHeli: remove use of motor_out array
...
No longer required for logging purposes as we have RCOU
11 years ago
851a538692
Copter: motor matrix comment change
11 years ago
652b4b4fe5
SingleCopter: motor test flaps servos in order
11 years ago
ccedf98238
Tri: call output_min at end of motors test
...
Minor change to comments
11 years ago
9f2086baf2
Copter: make motor_out array private
...
With new method of logging rc outputs access to the motor_out array is
not longer required
11 years ago
316ec5864e
AP_Motors: removed incorrect Makefile target
11 years ago
afbb199544
TradHeli: remove slash from parameter description
...
This may fix the issue in which the parameter descriptions are appearing
twice on the arducopter-parameters wiki page
11 years ago
330aa95769
Copter: default MOT_SPIN_ARMED to 70
11 years ago
7233a567fb
TradHeli: add accessor for phase_angle
11 years ago
c9c803ffd4
TradHeli: move STAB_COL_MIN to main parameter list
11 years ago
b71c6bfd76
TradHeli: add RSC_RUNUP_TIME param and rotor speed estimate
11 years ago
bc4dba0eea
TradHeli: ext gyro gain range 0 to 1000
11 years ago
197fc67897
TradHeli: move pilot desired rotor speed to heli.pde
11 years ago
942c14258b
TradHeli: ramp up changes
...
Rewrote tail and main rotor ramp up methods
Moved direct drive ESC speed control into rsc_control method
Pass in ch7 servo as servo_aux to TradHeli motors object constructor
split CH7_SETPOINT parameter into GYR_GAIN and DIRECTDRIVE parameters
replaced RSC_RATE with uint8_t RSC_RAMP_TIME parameter
rename GOV_SETPOINT parameter to RSC_SETPOINT
RSC_MODE parameter description updated to indicate it controls the
source of main rotor speed
11 years ago
9ac051c56d
TradHeli: BugFix to ColYaw
...
Credit to Jolyon Saunders for finding this bug.
11 years ago
4426060ccc
TradHeli: COLYAW not applied when the motor is not running
11 years ago
9ae66c1773
TradHeli: add support for drive tail rotors
...
Repurposed external gyro and made it multi-funcitonal.
required PWM on Ch8 to start the motor in RSC Mode moved up from 100 to 400. This is to facilitate two-stage switching of the motors with PWM>100 starting the tail motor, and PWM>400 starting the main motor.
Additional amendments by Randy
11 years ago
7ae0d3320b
TradHeli: add landing collective min
11 years ago
1f65bb537f
TradHeli: add get_pilot_desired_collective
...
Perhaps this should be moved to the main code's heli.pde sketch
11 years ago
13a412ee21
TradHeli: make parameters and variables private
...
add accessors for variables and params required in main code
replace tabs with spaces
11 years ago
2cc48ffcd6
Copter: formatting and param description changes
11 years ago
d54b1ea446
CopterMotors: fix example sketch
11 years ago
ce045c77a4
Copter: remove unused variable from Single copter
11 years ago
14dc1a1c88
Copter: add @User and @Increment to motor params description
11 years ago
e53c57b0a6
Copter: default SPIN_WHEN_ARMED to zero
11 years ago
81d83f1c55
SingleCopter: formatting changes
...
replace tab with 4-spaces
remove blank lines
11 years ago
07d3f2a3c5
Copter: add support for singlecopter airframe
...
this is the newest singlecopter airframe programme.
This kind of aerial vehicles include Honeywell T-hawk and Goldeneye.
11 years ago
5d946be77c
TradHeli: Change user description for COLYAW parameter.
11 years ago
bb1664185f
Copter: correct @Range of MOT_TCRV_MAXPCT parameter
11 years ago
78acea820f
Copter: fix symmetry in stability patch for Tricopters
...
Removes the "Increase opposing motors by 1/2 the overage of the high
motor" logic and merely moves all 3 motors down by the same amount if
one is over out_max. This eliminates the asymmetric scaling of
the previous logic when more than one motor is over out_max. This
resolves #537
11 years ago
943d7374f6
Copter: slow start motors from 0 to min throttle
11 years ago
53553751d1
Copter: Correctly set limit.lower flags for Tricopters
...
Resolves #536
11 years ago
e0c4785b2a
Copter: OctaQuad H-frame support
11 years ago
d3fcfe669d
Copter Motors: increase MOT_SPIN_ARMED to int16
12 years ago
5bef6dd539
AP_Motors: fixed example build
12 years ago
0a047ae1c1
Copter Motors: increased spin-when-armed to 70
...
Changed choices to be displayed in ground stations
12 years ago
62cb5c172b
Copter Motors: add slow start feature
...
Combined armed, frame orientation and slow_start into flags bitmask
Removed ability to set max throttle because it was never used
Re-ordered class variables
12 years ago
97b7130bb9
libraries: update license header to GPLv3
...
we switched to GPLv3 a long time ago, but neglected to update the
per-file license headers
12 years ago
01387a1553
AP_Motors: fixed examples build
12 years ago
0797489ad8
Motors: use AP_Notify static flags variable
12 years ago
f8a872f01e
AP_Motors: update notify
12 years ago
8d26fb5581
Copter Motors: by default spin motors at 65 when armed
12 years ago
fe412437c2
Copter: add flags for upper and lower throttle limits
...
Freeze desired altitude when motors hit a limit
12 years ago
Robert Lefebvre
Randy Mackay
Andrew Tridgell
ssq870424
texlan