// @Description: When zero, the flare sink rate (TECS_LAND_SINK) is a fixed sink demand. With this enabled the flare sinkrate will increase/decrease the flare sink demand as you get further beyond the LAND waypoint. Has no effect before the waypoint. This value is added to TECS_LAND_SINK proportional to distance traveled after wp. With an increasing sink rate you can still land in a given distance if you're traveling too fast and cruise passed the land point. A positive value will force the plane to land sooner proportional to distance passed land point. A negative number will tell the plane to slowly climb allowing for a pitched-up stall landing. Recommend 0.2 as initial value.
Let the warning flag be added by the build system and not when/if the
header AP_Common.h is included. Both waf and make were already updated
to contain these warnings. Besides being in the wrong place, with
clang++ we actually can't add "-Wno-" definitions in build system
because we enable all of the in the header with -Wall.
The ublox driver will now continuosly poll for the settings from the GPS and correct any that are found to be in correct.
This status is then reported to the arming library as an additional arming check, allowing the user to be sure that the
gps is correctly configured before using it. If a user has a GPS2 configured that is not present they will fail the arming
checks until after they have disabled the second GPS.
2 new parameters were introduced as well:
-GPS_AUTO_CONFIG: Will not request any configuration packets to attempt to change them. (If the packet is recieved then
a update will be sent to it, but in testing this scenario never occured. This is set to 1 or 0 to change the setting.
(Defaults to 1 enabling auto config)
-GPS_GNSS_MODE2: Behaves the same way as GPS_GNSS_MODE but only applies to the second GPS.
GPS drivers are now allowed 2 seconds of non responsiveness before being unloaded
when a NMEA sentence is corrupted we should discard it
completely. This change prevents us considering a set of sentences
that includes corrupted sentences from being seen as new data
Reverse thrust for controlled landings, even with much steeper approach slopes. This is achieved by allowing throttle demand to go negative to maintain a target airspeed. A Pre-Flare stage was added, triggered by an altitude, to allow for a slower airspeed just before land. That lower airspeed can be near stall.
new params TECS_APPR_SMAX - sink rate max during approach
This is the only driver doing this, using the system_initializing() from
scheduler to log selectively. Remove the check together with removal of
unused wrapper methods to semaphore.
Due to the way the headers are organized changing a single change in
an AP_Notify driver would trigger a rebuild for most of the files in
the project. Time could be saved by using ccache (since most of the
things didn't change) but we can do better, i.e. re-organize the headers
so we don't have to re-build everything.
Due to the way the headers are organized changing a single change in an
inertial sensor driver would trigger a rebuild for most of the files in
the project. Time could be saved by using ccache (since most of the
things didn't change) but we can do better, i.e. re-organize the headers
so we don't have to re-build everything.
With this patch only AP_InertialSensor/AP_InertialSensor.h is exposed to
most users. There are some corner cases to integrate with some example
code, but most of the places now depend only on this header and this
header doesn't depend on the specific backends.
Now changing a single header, e.g. AP_InertialSensor_L3G4200D.h triggers
a rebuild only of these files:
$ waf copter
'copter' finished successfully (0.000s)
Waf: Entering directory `/home/lucas/p/dronecode/ardupilot/build/minlure'
[ 80/370] Compiling libraries/AP_InertialSensor/AP_InertialSensor.cpp
[ 84/370] Compiling libraries/AP_InertialSensor/AP_InertialSensor_L3G4200D.cpp
[310/370] Linking build/minlure/ArduCopter/libArduCopter_libs.a
[370/370] Linking build/minlure/bin/arducopter
Waf: Leaving directory `/home/lucas/p/dronecode/ardupilot/build/minlure'
This is not used by any board and has a lot of commented out code. For
example, the compass is not enabled. The comment in the beginning of
the driver says it should serve as an example, but we should rather use
a working driver as an example. If this was at least a bit simpler and
that worked in the past we could refactor it to the new I2CDevice API.
This is not the case.
A string name allows to more easily expand the table: the board is
responsible for the name and doesn't have to declare it as a enum or
define. It's also easier to add 2 sensors of the same type.
Tom Pittenger
Lucas De Marchi
Michael du Breuil
Andrew Tridgell
Randy Mackay
mirkix
Daniel Frenzel
Paul Riseborough