zr-v4

Commit Graph

Author	SHA1	Message	Date
Michael du Breuil	bbcb976e73	Sub: Reduce dependency on inertial nav	6 years ago
Jacob Walser	4112fd1316	Sub: Remove mode header	8 years ago
Jacob Walser	3da4dc7089	Sub: home altitude is always 0, referenced from water's surface	8 years ago
Rustom Jehangir	617b439d0e	Sub: Match Copter changes	8 years ago
Rustom Jehangir	83ff3931b8	Sub: Refactor "Copter" to "Sub".	8 years ago
Rustom Jehangir	3da7c95e9b	Sub: New vehicle type, derived from ArduCopter.	8 years ago
Mathieu OTHACEHE	152edf7189	Global: remove mode line from headers Using a global .dir-locals.el file is a better alternative than reincluding the same emacs header in every file of the project.	8 years ago
Randy Mackay	13c26eab67	Copter: update current_loc at 400hz	9 years ago
Andrew Tridgell	278883c521	Copter: finished conversion to .cpp files Pair-Programmed-With: Randy Mackay <rmackay9@yahoo.com>	10 years ago
Andrew Tridgell	356ece3402	Copter: rename .pde files to .cpp files	10 years ago
Randy Mackay	2a1a105462	Copter: current alt is alt above-ekf-origin until home set	10 years ago
Randy Mackay	c3bdb9a13e	Copter: update inertial alt only after home is set	10 years ago
Randy Mackay	4d566bf462	Copter: current_loc.alt is alt-above-home	10 years ago
Randy Mackay	50e024fe8f	Copter: flag current alt as relative This is required so common Log_Write_Camera can calculate relative and abs altitudes provided by either copter or plane pair programmed with Craig Elder	11 years ago
Randy Mackay	138c2803be	Copter: combine NTUN and INAV dataflash msgs	11 years ago
Randy Mackay	1793ee804e	Copter: remove armed check before logging	11 years ago
Andrew Tridgell	5ad9deecfb	Copter: cleanup some bit if tests to be clearer Pair-Programmed-With: Randy Mackay <rmackay9@yahoo.com>	12 years ago
Randy Mackay	67c69a19ee	Copter: remove baro-only alt hold Saves 8 bytes of memory and more importantly simplifies the alt hold calculations	12 years ago
rmackay9	92e271e517	AP_InertialNav: increase baro delay to 0.5 sec (was 0.2sec) to allow slower baro updates on APM1	12 years ago
rmackay9	072ffec493	ArduCopter: allow INERTIAL_NAV to be enabled separately for horizontal and vertical position	12 years ago
rmackay9	1f801714e8	ArduCopter: incorporate new version of inertial navigation Moved several navigation functions from ArduCopter.pde to navigation.pde	12 years ago
rmackay9	a1b4ec6d0e	ArduCopter: move to use new INS library instead of IMU library	12 years ago
uncrustify	a20f75e12c	uncrustify ArduCopter/inertia.pde	13 years ago
Jason Short	e09d6ad7a8	Arducopter Simplified the inertial calcs for now	13 years ago
Jason Short	92d481c08c	inertia.pde: WIP don't fly with inertia enabled until FN.	13 years ago
Jason Short	8b212d8baa	Adjustments to the Inertial_nav lowered Rate_I and Rate_P to be less jumpy. raised throttle_p added a clear to rate when entering loiter moved the raw reporting	13 years ago
Jason Short	c42f9ece43	Inertial Control I added inertial navigation based on the simulator data. This is an option only available if you compile with Arduino and set #define INERTIAL_NAV ENABLED in the APM_Config.h file. This has been tested for one real flight and did not crash my quad, but consider it very alpha. The quad may be unpredictable at first until the error correction fixes poorly calibrated accels. Be Careful. Most of the real work is in the inertia file, but the error correction, new variable defines and calibration calls are sprinkled throughout. The Log should record RAW messages with special debugging values.	13 years ago

6 Commits (24f6aee93ce4cd275c3df7571b288b03a13f5228)