Minlure is a port of ArduPilot to Minnow Board connected to daughter
board. Very few of those were produced and nobody is flying with it.
It served its purpose and all the the improvements to ArduPilot remain
regardless of it not being supported anymore. Now it's just adding
maintenance work with no clear benefit, so pull the plug.
See discussion here:
https://github.com/ArduPilot/ardupilot/issues/7331
we were getting some uninitialised variables. While it only showed up in
AP_SbusOut, it means we can't be sure it won't happen on other objects,
so safest to remove the approach
Thanks to assistance from Lucas, Peter and Francisco
Navio2 exports its leds via /sys/class/leds interface. We reuse it in
order not to conflict with GPIO_Sysfs. Otherwise we'd get a Device Busy
error in GPIO_Sysfs::_export_pin().
If parameter INS_GYRO_CAL is disabled, usually because operator is
arming on a moving vehicle such as a boat, the Oreo LEDs would wait
indefinitely for a gyro calibration that will never happen. This
removes that dependency. The LEDs will strobe blue only when gyros are
actually initializing. Not before. Consequently, this greatly
simiplifies that portion of the code.
cork()/push() will be called in the vehicle code.
The issue that led to this fix was as follows:
- on a Linux board (Navio 2) usage of this class didn't yield any PWM on
the expected outputs on Rover (Copter and Plane worked as expected)
After dicsussion at #6339 rover code was changed (541538f) to use make
proper use of SRV_Channels API.
This fix is also the consequence of the discussion. TL;DR: the output is
only done when commanded by the vehicle.
Reworked the process flow. Created the aviation vs rover themes.
Created visual operator feedback for prearm checks, GPS, EKF, gyro init,
radio failsafe, and low battery. This also includes work by Hugh Eaves
to open up the full extended properties of the Oreo LEDs. Not only are
far more functions available, but you can override and do custom things
via mavlink.
Jaime did the hard work on this one. He reworked notify device
selection to take place on init rather than on compile like before. The
notify decivces are mostly set on compile using preprocessor directives
based on board type. I created NTF_OREO_THEME. This will allow the
user to enable/disable the OreoLED driver. And it also allows you to
select between aircraft and rover lighting themes. This allows the Solo
to use the OreoLEDs, and doesn't waste the memory on vehicles not
equipped with Oreo LEDs. The OreoLED driver is restricted to Pixhawk 2
FCs by proprocessor directive due to memory constraints. So it will
never work by accident on another board.
There is also a new notify flag for GPS Fusion. This flag is true when
the EKF is happy with the GPS, actively using it for position
information.
Evaluated solo specific tones file vs standard px4 tones files. The
only thing the Solo had that standard ArduPilot does not have is the GPS
unplugged tone and the power off tone.
* Some tones have a different tune, which is fine. We want the Solo to
sound like ArduPilot if it is running ArduPilot.
* GPS unplugged tone abandoned. Determined to be unnecessary.
* Power off tone merged into standard px4 tones file. Smart battery
signalling a power off will make use of this tone. Has application for
any smart battery equipped vehicle, not just Solo.
* Removed all references and dependencies to `ToneAlarm_PX4_Solo.cpp`
and `ToneAlarm_PX4_Solo.h`
* Deleted `ToneAlarm_PX4_Solo.cpp` and `ToneAlarm_PX4_Solo.h` since
they're no longer needed.
Andrew Tridgell
Michael du Breuil
Alexander Malishev
Lucas De Marchi
mirkix
Peter Barker
priseborough
night-ghost
Nikita Tomilov
Tom Pittenger
Mark Whitehorn
HeBin
Georgii Staroselskii
Georgii Staroselskii
Lucas De Marchi
Matt
Randy Mackay
murata