Added WP to Loiter_time so you can spec a specific location in the planner
added new Navigation alg. Should perform better (doesn't rely on 45° flow fields like last one)
Added "Jump" counter so missions don't get overwritten in flight.
removed I term by default for Rate pitch and roll
Change the way Rate nav works. we now take into account both forward *and lateral* rates. The signs may be backward so be careful! Let me know if the quad shoots off to one side and I'll flip the signs.
git-svn-id: https://arducopter.googlecode.com/svn/trunk@3049 f9c3cf11-9bcb-44bc-f272-b75c42450872
moved ground start to first arming
added ground start flag
moved throttle_integrator to 50hz loop
CAMERA_STABILIZER deprecated - now always on
renamed current logging bit mask to match APM
added MA filter to PID - D term
Adjusted PIDs based on continued testing and new PID filter
added MASK_LOG_SET_DEFAULTS to match APM
moved some stuff out of ground start into system start where it belonged
Added slower Yaw gains for DCM when the copter is in the air
changed camera output to be none scaled PWM
fixed bug where ground_temperature was unfiltered
shortened Baro startup time
fixed issue with Nav_WP integrator not being reset
RTL no longer yaws towards home
Circle mode for flying a 10m circle around the point where it was engaged. - Not tested at all! Consider Circle mode as alpha.
git-svn-id: https://arducopter.googlecode.com/svn/trunk@2966 f9c3cf11-9bcb-44bc-f272-b75c42450872
defaults for these are already in config.h, but protected with #ifndef
wrappers. The #ifndef wrappers are useful to allow users to have
makefile targets for different configs, so you can (for example), do
"make heli" with a local makefile
This makes it easier for developers to ensure that all configs build
correctly
git-svn-id: https://arducopter.googlecode.com/svn/trunk@2890 f9c3cf11-9bcb-44bc-f272-b75c42450872
Before: -> After
Stabilize P –> Stabilize P (Use NG values, or 8.3 x the older AC2 value)
Stabilize I –> Stabilize I (Stays same value)
Stabilize D –> Rate P (Stays same value)
–> Rate I (new)
Added a new value – an I term for rate. The old stabilization routines did not use this term. Please refer to the config.h file to read more about the new PIDs.
Added framework for using DCM corrected Accelerometer rates. Code is commented out for now.
Added set home at Arming.
Crosstrack is now a full PID loop, rather than just a P gain for more control.
Throttle now slews when switching out of Alt hold or Auto modes for less jarring transitions
Sonar and Baro PIDs are now combined into a throttle PID Yaw control is completely re-written.
Added Octa_Quad support - Max
git-svn-id: https://arducopter.googlecode.com/svn/trunk@2836 f9c3cf11-9bcb-44bc-f272-b75c42450872
new Loiter PIDs
tuned down control on standard frame
shunk the mixing range for sonar from 3 meters to 2 meters
added framework for Guided mode - not tested!
removed pitch and roll deadzone
decoupled SIMPLE mode from LOITER PIDs
Synced Mavlink with APM
Logs report correct WP number now.
disabled Sonar spike filter.
git-svn-id: https://arducopter.googlecode.com/svn/trunk@2722 f9c3cf11-9bcb-44bc-f272-b75c42450872
Fixed Mavlink issue
Added look at home option for SIMPLE mode. Off be default. Untested.
Upped performance of Yaw.
git-svn-id: https://arducopter.googlecode.com/svn/trunk@2695 f9c3cf11-9bcb-44bc-f272-b75c42450872
Includes updated motor tests. These need to be verified.
Nav loiter D was added (.03) - verify this helps.
Nav_lat is now filtered for Rate control. This is to keep jerky pitching to a minimum.
git-svn-id: https://arducopter.googlecode.com/svn/trunk@2448 f9c3cf11-9bcb-44bc-f272-b75c42450872
Made minor change in Loiter to check something.
Motor LEDs enabled. Let me know if they work OK.
Armed Motors is now Solid to match GPS behavior.
git-svn-id: https://arducopter.googlecode.com/svn/trunk@2421 f9c3cf11-9bcb-44bc-f272-b75c42450872
Added Octo Support
Fixed Loiter issue regarding Yaw towards loiter location
Added Yaw control alternative for testing
decreased Yaw deadband to +-5°
revved to 2.0.10
git-svn-id: https://arducopter.googlecode.com/svn/trunk@2391 f9c3cf11-9bcb-44bc-f272-b75c42450872
Added Octo Support
Fixed Loiter issue regarding Yaw towards loiter location
Added Yaw control alternative for testing
decreased Yaw deadband to +-5°
revved to 2.0.10
git-svn-id: https://arducopter.googlecode.com/svn/trunk@2389 f9c3cf11-9bcb-44bc-f272-b75c42450872
Jason Short
Jason Short
Jani Hirvinen
Andrew Tridgell
Michael Oborne
Amilcar Lucas
jasonshort
jphelirc
tridge60@gmail.com
rmackay9@yahoo.com