9e04029699
Plane: limit ATC_MOT_MIX_MAX in case of a fly away
5 years ago
ee96ec7f0d
Plane: Support new AP_Vehicle::set_mode
5 years ago
edb5f05339
Plane: minor comment changes
5 years ago
1a2abae902
Plane: reduce QTUN log rate to 25Hz
5 years ago
9405fd6958
Plane: remove unused location argument to control_auto
5 years ago
f9580424f6
Plane: Resore old default behaviour for throttle curves
...
The change in this made QStabilize behave very differently then it had,
which is quite shocking in a test flight.
5 years ago
db4ae9ff24
Plane: check airspeed and active Z controll for hover learning
5 years ago
5c43b18672
Plane: fixed height_above_ground() for case when rangefinder is below min
...
this prevents a rangefinder that goes below min distance from causing
the calculations that depend on height above ground to fail
5 years ago
34b0967d09
Plane: prevent fwd motor from spinning up on ground in quadplane landing
...
if the rangefinder starts to measure below it's min range then the fwd
motor can spin up.
Thanks to Josh for reporting this!
5 years ago
7751352a86
Plane: implement VTOL landing for AFS termination
...
this allows for vertical landing as an AFS_TERM_ACTION
5 years ago
788e7a840c
Plane: default angle_boost to disabled for tailsitters
5 years ago
4f22dff14d
Plane: Add an airspeed limit for quadplane takeoffs
6 years ago
77afcf6a1b
Plane: Abort takeoffs that take to long to complete
6 years ago
7178655cbe
Plane: fixed landing after VTOL loiters
6 years ago
34da437266
Plane: support for upgrade to PID object
6 years ago
157f786adf
Global: rename desired to target in PID info
6 years ago
22598b1a4b
Plane: Reduce inerital nav dependence
6 years ago
44f6f7335e
Plane: Added Quadplane option for QRTL failsafe action
6 years ago
76663d66e8
Plane: support bicopter tiltrotors
6 years ago
220176f283
Plane: added octa I frame
6 years ago
400aa53654
Plane: move arming-related functionality into parent classes
...
Logging moves up
arming via mavlink moves up
arming via switch moves up
6 years ago
34a1cf9528
Plane: move callback setup to QuadPlane::setup()
6 years ago
aeaff72e14
Plane: fix acro stabilization check
6 years ago
4a7ce1b384
Plane: clean up qacro
6 years ago
dd50d435ab
Plane: limit bodyframe roll mode to tailsitters
6 years ago
f054301ec2
Plane: add QACRO roll/pitch/yaw rate params
6 years ago
8bcf2439ad
Plane: quadplane stabilize manual throttle midpoint and expo
...
move throttle curve logic to AP_Math
use parameter THROTTLE_EXPO in get_pilot_throttle
6 years ago
b515431008
AP_Math: add expo and throttle_curve functions
6 years ago
65b4ba0539
ArduPlane: use past_interval_finish_line and line_path_proportion from Location
6 years ago
f09822a400
Plane: adjust for desired spool state and spool state renames
6 years ago
d8990a002e
Plane: update locations_are_same to same_latlon_as
6 years ago
47141562c0
ArduPlane: use get_distance_NE instead of location_diff
6 years ago
2daa5ffb9e
Plane: replace set_throttle_out_unstabilized
6 years ago
ade6281923
Plane: use #if ADVANCED_FAILSAFE == ENABLED just like Rover and Copter
6 years ago
0270c57530
Plane: massive refactor and creation of Mode class
6 years ago
e0765747e7
Plane: add new tailsitter bodyframe roll option
6 years ago
825055d736
Plane: add rate-only option for QACRO mode
6 years ago
6414f0e48e
Plane: skip plane assignments in QACRO
6 years ago
2b6210d594
Plane: use WP height for height above ground in vtol landing
...
this allows for landings above or below the takeoff height without
requiring the use of terrain data. It allows both the use of vfwd
motor for holding against wind, and the correct height for land final
descent rate
6 years ago
b4103d04cc
Plane: never use vfwd motor if vtol motors shutdown
6 years ago
7908ad437e
Plane: allow fwd motor to run in VTOL land hor positioning
...
this fixes an issue with vtol landings below the takeoff point
6 years ago
ca7566fff9
Plane: use enum class for ArmingMethod and ArmingRequired
6 years ago
cbb0bfb809
Plane: is_flying_vtol: if spool mode is shut down we are not flying
...
The subsequent check for get_throttle passes if you switch from QHOVER
to MANUAL on the ground while armed. get_throttle returns > 0.01 - but
the motors are shut down so no output occurs.
6 years ago
4a6b97828f
ArduPlane: add tailsitter input type TAILSITTER_INPUT_BF_ROLL
6 years ago
01d6f1d932
ArduPlane: add body-frame yaw mode for tailsitters
6 years ago
6e4a2b97f9
ArduPlane:add subclass for copter tailsitters
...
cleanup and add tailsit_motmx
add constexpr and motor mask check
add support for tricopter tailsitter
don't call output_motor_mask unless armed
fix whitespace
6 years ago
487ad7a90f
Plane: add QACRO mode for quadplanes
...
use acro_r/p/y_rate params in qacro
port ACRO throttle handling from copter
handle non-tailsitter controls
6 years ago
f24c6785f2
Plane: add E-stop
6 years ago
136e10a781
Plane: handle VTOL landing with incorrect height
...
if landing above expected height then run landing detector to allow a
switch from LAND_DESCEND to LAND_FINAL
this prevents the plane sitting on the ground until the battery runs
out
6 years ago
b290148ed0
Plane: Don't overwrite the quadplane loiter relax
6 years ago
Leonard Hall
Michael du Breuil
Randy Mackay
Mark Whitehorn
sas
Andrew Tridgell
Henry Wurzburg
IamPete1
1iggy2
Peter Barker
Pierre Kancir
Tom Pittenger