The maximum time copters can reject GPS has been reduced from 10 to 7 seconds as flight logs have show that inertial dead reckoning with vibration and calibration errors is not good enough to support 10 seconds without aiding.
This patch causes the EKF to update the height of its origin each time it receives a valid GPs message whislt disarmed.
The resultant EKF origin height represents the height of the zero baro alt datum relative to the GPS height datum.
Flight tests have shown that the magnetic field distortion associated with flight from steel structures can extend 3m or higher. To counteract this, a second and final yaw and magnetic field alignment has been added which is activated when the height exceeds 5m for the first time.
Logic used to delay optical flow and airspeed fusion to prevent it occurring on the same time step as magnetometer fusion has been removed. This is no longer required to efficiency improvements made at the firmware level.
Improvements in PX4 firmware have reduced the computational load and mkae the previous practicwe of splitting magnetometer and optical flow fusion across multiple time steps unnecessary and make it possible to perform a covariance prediction prior to fusing data on the same time step. This patch:
1) Ensures that a covariance prediction is always performed prior to fusion of any observation
2) Removes the splitting of magnetometer fusion so that fusion of the X,Y and Z components occurs on the same time time step
3) Removes the splitting of optical flow fusion so that fusion of X and Y components occurs on the same time step
UBlox receivers report an estimate of the speed accuracy that tests show correlates well to speed glitches. Using this to scale the GPS velocity observation noise will reduce the effect of bad GPS velocity data.
If the vehicle moves significantly or the GPS changes position significantly pre-armed, then the GPS glitch logic was being invoked when the first GPs measurements were fused. This patch resets the position to the GPS when the vehicle arms.
Due to the way that gyro calibration is done, the EKF could be effectively not run for up to 30 seconds in extreme cases, making it possible that the GPS would be failed on arming and the copter put into a non-GPS mode.
the longer term solution is to update the gyro calibration so that it does not hold up other processing. the short tyermfix in thsi patch is to look for evidence of a 3D lock in the last received GPS message.
This fixes a bug that meant that once the EKF had started up in a non-GPS mode, it would no longer read the GPS and therefore would never be able to use GPS again until reset.
When Copter arms, the AHRS/EKF may not be run for a few hundred msec depending on conditions. This can cause the arming check to fail the optical flow sensor and place the EKF in a constant position mode.
This additional explicit setting of the constPosMode and constVelMode reduces the likelihood of logic errors being introduced in the future as it places the intended setting of these parameters at arming in the one place. the constVelmode and constPosMode only have one set of conditions each that can trigger these modes in flight, so if these modes are true after arming it will be clear that it was the in-flight condition that triggered.
This ensures the position and velocity measurement status will be set as timed out immediately after use of those measurements is inhibited. This will improve the timeliness of filter status reporting.
It does not make sense to relax the limits on vehicle speed and nav gains just because we have received some invalid flow data. This could make the situation worse if the invalid data was being caused by too much speed.
If we are relying on flow data the vehicle limits should always be applied.
When we are not using GPS measurements, we should not be allowing the GPS glitch logic to reset position states as this can interfere with operation of non GPS modes.
When PV aiding is disabled, then the timeout time reference should not be reset becasue we want the position measurement timeout status to remain true the whole time the measurement is not being used.
Synchronise with covariance prediction to improve numerical stability and accuracy of angle corrections. The 'noise' this produces in the position and velocity estimate is irrelevantbecause these are not used by the control loops during this mode of operation (they are nominally zero anyway).
Prevents possible loss of attitude reference for flights without optical flow and GPS.
The optical flow measurement timeout can reset the velocity states which decouples the position states from IMU errors and therefore significantly reduces the amount of attitude error correction.
This enables the filter to report the last known position after disarm.
The LLH location of the filters NED origin is published and should be logged every time the vehicle is armed to assist with post-flight trajectory reconstruction.
The LLH location of the filters NED origin can be set externally whilst the vehicle is disarmed.
Paul Riseborough
Jonathan Challinger
Andrew Tridgell
Randy Mackay
Grant Morphett