// -*- tab-width: 4; Mode: C++; c-basic-offset: 4; indent-tabs-mode: nil -*-
#ifndef _DEFINES_H
#define _DEFINES_H
#include <AP_HAL_Boards.h>
// Just so that it's completely clear...
#define ENABLED 1
#define DISABLED 0
// this avoids a very common config error
#define ENABLE ENABLED
#define DISABLE DISABLED
// Flight modes
// ------------
#define AUTO_YAW_HOLD 0 // pilot controls the heading
#define AUTO_YAW_LOOK_AT_NEXT_WP 1 // point towards next waypoint (no pilot input accepted)
#define AUTO_YAW_ROI 2 // point towards a location held in roi_WP (no pilot input accepted)
#define AUTO_YAW_LOOK_AT_HEADING 3 // point towards a particular angle (not pilot input accepted)
#define AUTO_YAW_LOOK_AHEAD 4 // point in the direction the copter is moving
#define AUTO_YAW_RESETTOARMEDYAW 5 // point towards heading at time motors were armed
// Ch6, Ch7 and Ch8 aux switch control
#define AUX_SWITCH_PWM_TRIGGER_HIGH 1800 // pwm value above which the ch7 or ch8 option will be invoked
#define AUX_SWITCH_PWM_TRIGGER_LOW 1200 // pwm value below which the ch7 or ch8 option will be disabled
#define CH6_PWM_TRIGGER_HIGH 1800
#define CH6_PWM_TRIGGER_LOW 1200
#define AUX_SWITCH_DO_NOTHING 0 // aux switch disabled
#define AUX_SWITCH_SET_HOVER 1 // deprecated
#define AUX_SWITCH_FLIP 2 // flip
#define AUX_SWITCH_SIMPLE_MODE 3 // change to simple mode
#define AUX_SWITCH_RTL 4 // change to RTL flight mode
#define AUX_SWITCH_SAVE_TRIM 5 // save current position as level
#define AUX_SWITCH_ADC_FILTER 6 // deprecated
#define AUX_SWITCH_SAVE_WP 7 // save mission waypoint or RTL if in auto mode
#define AUX_SWITCH_MULTI_MODE 8 // depending upon CH6 position Flip (if ch6 is low), RTL (if ch6 in middle) or Save WP (if ch6 is high)
#define AUX_SWITCH_CAMERA_TRIGGER 9 // trigger camera servo or relay
#define AUX_SWITCH_SONAR 10 // allow enabling or disabling sonar in flight which helps avoid surface tracking when you are far above the ground
#define AUX_SWITCH_FENCE 11 // allow enabling or disabling fence in flight
#define AUX_SWITCH_RESETTOARMEDYAW 12 // changes yaw to be same as when quad was armed
#define AUX_SWITCH_SUPERSIMPLE_MODE 13 // change to simple mode in middle, super simple at top
#define AUX_SWITCH_ACRO_TRAINER 14 // low = disabled, middle = leveled, high = leveled and limited
#define AUX_SWITCH_SPRAYER 15 // enable/disable the crop sprayer
#define AUX_SWITCH_AUTO 16 // change to auto flight mode
#define AUX_SWITCH_AUTOTUNE 17 // auto tune
#define AUX_SWITCH_LAND 18 // change to LAND flight mode
#define AUX_SWITCH_EPM 19 // Operate the EPM cargo gripper low=off, middle=neutral, high=on
#define AUX_SWITCH_EKF 20 // Enable NavEKF
#define AUX_SWITCH_PARACHUTE_ENABLE 21 // Parachute enable/disable
#define AUX_SWITCH_PARACHUTE_RELEASE 22 // Parachute release
#define AUX_SWITCH_PARACHUTE_3POS 23 // Parachute disable, enable, release with 3 position switch
#define AUX_SWITCH_MISSIONRESET 24 // Reset auto mission to start from first command
#define AUX_SWITCH_ATTCON_FEEDFWD 25 // enable/disable the roll and pitch rate feed forward
#define AUX_SWITCH_ATTCON_ACCEL_LIM 26 // enable/disable the roll, pitch and yaw accel limiting
#define AUX_SWITCH_RETRACT_MOUNT 27 // Retract Mount
#define AUX_SWITCH_RELAY 28 // Relay pin on/off (only supports first relay)
// values used by the ap.ch7_opt and ap.ch8_opt flags
#define AUX_SWITCH_LOW 0 // indicates auxiliar switch is in the low position (pwm <1200)
#define AUX_SWITCH_MIDDLE 1 // indicates auxiliar switch is in the middle position (pwm >1200, <1800)
#define AUX_SWITCH_HIGH 2 // indicates auxiliar switch is in the high position (pwm >1800)
// Frame types
#define UNDEFINED_FRAME 0
#define QUAD_FRAME 1
#define TRI_FRAME 2
#define HEXA_FRAME 3
#define Y6_FRAME 4
#define OCTA_FRAME 5
#define HELI_FRAME 6
#define OCTA_QUAD_FRAME 7
#define SINGLE_FRAME 8
#define COAX_FRAME 9
// Internal defines, don't edit and expect things to work
// -------------------------------------------------------
#define ToRad(x) radians(x) // *pi/180
#define ToDeg(x) degrees(x) // *180/pi
// HIL enumerations
#define HIL_MODE_DISABLED 0
#define HIL_MODE_SENSORS 1
// Auto Pilot modes
// ----------------
#define STABILIZE 0 // hold level position
#define ACRO 1 // rate control
#define ALT_HOLD 2 // AUTO control
#define AUTO 3 // AUTO control
#define GUIDED 4 // AUTO control
#define LOITER 5 // Hold a single location
#define RTL 6 // AUTO control
#define CIRCLE 7 // AUTO control
#define LAND 9 // AUTO control
#define OF_LOITER 10 // Hold a single location using optical flow sensor
#define DRIFT 11 // DRIFT mode (Note: 12 is no longer used)
#define SPORT 13 // earth frame rate control
#define FLIP 14 // flip the vehicle on the roll axis
#define AUTOTUNE 15 // autotune the vehicle's roll and pitch gains
#define POSHOLD 16 // position hold with manual override
#define NUM_MODES 17
// CH_6 Tuning
// -----------
#define CH6_NONE 0 // no tuning performed
#define CH6_STABILIZE_ROLL_PITCH_KP 1 // stabilize roll/pitch angle controller's P term
#define CH6_RATE_ROLL_PITCH_KP 4 // body frame roll/pitch rate controller's P term
#define CH6_RATE_ROLL_PITCH_KI 5 // body frame roll/pitch rate controller's I term
#define CH6_RATE_ROLL_PITCH_KD 21 // body frame roll/pitch rate controller's D term
#define CH6_STABILIZE_YAW_KP 3 // stabilize yaw heading controller's P term
#define CH6_YAW_RATE_KP 6 // body frame yaw rate controller's P term
#define CH6_YAW_RATE_KD 26 // body frame yaw rate controller's D term
#define CH6_ALTITUDE_HOLD_KP 14 // altitude hold controller's P term (alt error to desired rate)
#define CH6_THROTTLE_RATE_KP 7 // throttle rate controller's P term (desired rate to acceleration or motor output)
#define CH6_THROTTLE_ACCEL_KP 34 // accel based throttle controller's P term
#define CH6_THROTTLE_ACCEL_KI 35 // accel based throttle controller's I term
#define CH6_THROTTLE_ACCEL_KD 36 // accel based throttle controller's D term
#define CH6_LOITER_POSITION_KP 12 // loiter distance controller's P term (position error to speed)
#define CH6_LOITER_RATE_KP 22 // loiter rate controller's P term (speed error to tilt angle)
#define CH6_LOITER_RATE_KI 28 // loiter rate controller's I term (speed error to tilt angle)
#define CH6_LOITER_RATE_KD 23 // loiter rate controller's D term (speed error to tilt angle)
#define CH6_WP_SPEED 10 // maximum speed to next way point (0 to 10m/s)
#define CH6_ACRO_RP_KP 25 // acro controller's P term. converts pilot input to a desired roll, pitch or yaw rate
#define CH6_ACRO_YAW_KP 40 // acro controller's P term. converts pilot input to a desired roll, pitch or yaw rate
#define CH6_RELAY 9 // deprecated -- remove
#define CH6_HELI_EXTERNAL_GYRO 13 // TradHeli specific external tail gyro gain
#define CH6_OPTFLOW_KP 17 // deprecated -- remove
#define CH6_OPTFLOW_KI 18 // deprecated -- remove
#define CH6_OPTFLOW_KD 19 // deprecated -- remove
#define CH6_AHRS_YAW_KP 30 // ahrs's compass effect on yaw angle (0 = very low, 1 = very high)
#define CH6_AHRS_KP 31 // accelerometer effect on roll/pitch angle (0=low)
#define CH6_INAV_TC 32 // deprecated -- remove
#define CH6_DECLINATION 38 // compass declination in radians
#define CH6_CIRCLE_RATE 39 // circle turn rate in degrees (hard coded to about 45 degrees in either direction)
#define CH6_SONAR_GAIN 41 // sonar gain
#define CH6_EKF_VERTICAL_POS 42 // EKF's baro vs accel (higher rely on accels more, baro impact is reduced). Range should be 0.2 ~ 4.0? 2.0 is default
#define CH6_EKF_HORIZONTAL_POS 43 // EKF's gps vs accel (higher rely on accels more, gps impact is reduced). Range should be 1.0 ~ 3.0? 1.5 is default
#define CH6_EKF_ACCEL_NOISE 44 // EKF's accel noise (lower means trust accels more, gps & baro less). Range should be 0.02 ~ 0.5 0.5 is default (but very robust at that level)
#define CH6_RC_FEEL_RP 45 // roll-pitch input smoothing
#define CH6_RATE_PITCH_KP 46 // body frame pitch rate controller's P term
#define CH6_RATE_PITCH_KI 47 // body frame pitch rate controller's I term
#define CH6_RATE_PITCH_KD 48 // body frame pitch rate controller's D term
#define CH6_RATE_ROLL_KP 49 // body frame roll rate controller's P term
#define CH6_RATE_ROLL_KI 50 // body frame roll rate controller's I term
#define CH6_RATE_ROLL_KD 51 // body frame roll rate controller's D term
#define CH6_RATE_PITCH_FF 52 // body frame pitch rate controller FF term
#define CH6_RATE_ROLL_FF 53 // body frame roll rate controller FF term
#define CH6_RATE_YAW_FF 54 // body frame yaw rate controller FF term
// Acro Trainer types
#define ACRO_TRAINER_DISABLED 0
#define ACRO_TRAINER_LEVELING 1
#define ACRO_TRAINER_LIMITED 2
// RC Feel roll/pitch definitions
#define RC_FEEL_RP_VERY_SOFT 0
#define RC_FEEL_RP_SOFT 25
#define RC_FEEL_RP_MEDIUM 50
#define RC_FEEL_RP_CRISP 75
#define RC_FEEL_RP_VERY_CRISP 100
// Yaw behaviours during missions - possible values for WP_YAW_BEHAVIOR parameter
#define WP_YAW_BEHAVIOR_NONE 0 // auto pilot will never control yaw during missions or rtl (except for DO_CONDITIONAL_YAW command received)
#define WP_YAW_BEHAVIOR_LOOK_AT_NEXT_WP 1 // auto pilot will face next waypoint or home during rtl
#define WP_YAW_BEHAVIOR_LOOK_AT_NEXT_WP_EXCEPT_RTL 2 // auto pilot will face next waypoint except when doing RTL at which time it will stay in it's last
#define WP_YAW_BEHAVIOR_LOOK_AHEAD 3 // auto pilot will look ahead during missions and rtl (primarily meant for traditional helicotpers)
// Auto modes
enum AutoMode {
Auto_TakeOff,
Auto_WP,
Auto_Land,
Auto_RTL,
Auto_CircleMoveToEdge,
Auto_Circle,
Auto_Spline,
Auto_NavGuided,
Auto_Loiter
};
// Guided modes
enum GuidedMode {
Guided_TakeOff,
Guided_WP,
Guided_Velocity,
Guided_Spline
};
// RTL states
enum RTLState {
InitialClimb,
ReturnHome,
LoiterAtHome,
FinalDescent,
Land
};
// Flip states
enum FlipState {
Flip_Start,
Flip_Roll,
Flip_Pitch_A,
Flip_Pitch_B,
Flip_Recover,
Flip_Abandon
};
// LAND state
#define LAND_STATE_FLY_TO_LOCATION 0
#define LAND_STATE_DESCENDING 1
// Logging parameters
#define TYPE_AIRSTART_MSG 0x00
#define TYPE_GROUNDSTART_MSG 0x01
#define LOG_ATTITUDE_MSG 0x01
#define LOG_MODE_MSG 0x03
#define LOG_CONTROL_TUNING_MSG 0x04
#define LOG_NAV_TUNING_MSG 0x05
#define LOG_PERFORMANCE_MSG 0x06
#define LOG_CURRENT_MSG 0x09
#define LOG_STARTUP_MSG 0x0A
#define LOG_OPTFLOW_MSG 0x0C
#define LOG_EVENT_MSG 0x0D
#define LOG_PID_MSG 0x0E // deprecated
#define LOG_COMPASS_MSG 0x0F
#define LOG_INAV_MSG 0x11 // deprecated
#define LOG_CAMERA_MSG_DEPRECATED 0x12 // deprecated
#define LOG_ERROR_MSG 0x13
#define LOG_DATA_INT16_MSG 0x14
#define LOG_DATA_UINT16_MSG 0x15
#define LOG_DATA_INT32_MSG 0x16
#define LOG_DATA_UINT32_MSG 0x17
#define LOG_DATA_FLOAT_MSG 0x18
#define LOG_AUTOTUNE_MSG 0x19
#define LOG_AUTOTUNEDETAILS_MSG 0x1A
#define LOG_COMPASS2_MSG 0x1B
#define LOG_COMPASS3_MSG 0x1C
#define MASK_LOG_ATTITUDE_FAST (1<<0)
#define MASK_LOG_ATTITUDE_MED (1<<1)
#define MASK_LOG_GPS (1<<2)
#define MASK_LOG_PM (1<<3)
#define MASK_LOG_CTUN (1<<4)
#define MASK_LOG_NTUN (1<<5)
#define MASK_LOG_RCIN (1<<6)
#define MASK_LOG_IMU (1<<7)
#define MASK_LOG_CMD (1<<8)
#define MASK_LOG_CURRENT (1<<9)
#define MASK_LOG_RCOUT (1<<10)
#define MASK_LOG_OPTFLOW (1<<11)
#define MASK_LOG_PID (1<<12) // deprecated
#define MASK_LOG_COMPASS (1<<13)
#define MASK_LOG_INAV (1<<14) // deprecated
#define MASK_LOG_CAMERA (1<<15)
#define MASK_LOG_WHEN_DISARMED (1UL<<16)
#define MASK_LOG_ANY 0xFFFF
// DATA - event logging
#define DATA_MAVLINK_FLOAT 1
#define DATA_MAVLINK_INT32 2
#define DATA_MAVLINK_INT16 3
#define DATA_MAVLINK_INT8 4
#define DATA_AP_STATE 7
#define DATA_INIT_SIMPLE_BEARING 9
#define DATA_ARMED 10
#define DATA_DISARMED 11
#define DATA_AUTO_ARMED 15
#define DATA_TAKEOFF 16
#define DATA_LAND_COMPLETE_MAYBE 17
#define DATA_LAND_COMPLETE 18
#define DATA_NOT_LANDED 28
#define DATA_LOST_GPS 19
#define DATA_FLIP_START 21
#define DATA_FLIP_END 22
#define DATA_SET_HOME 25
#define DATA_SET_SIMPLE_ON 26
#define DATA_SET_SIMPLE_OFF 27
#define DATA_SET_SUPERSIMPLE_ON 29
#define DATA_AUTOTUNE_INITIALISED 30
#define DATA_AUTOTUNE_OFF 31
#define DATA_AUTOTUNE_RESTART 32
#define DATA_AUTOTUNE_SUCCESS 33
#define DATA_AUTOTUNE_FAILED 34
#define DATA_AUTOTUNE_REACHED_LIMIT 35
#define DATA_AUTOTUNE_PILOT_TESTING 36
#define DATA_AUTOTUNE_SAVEDGAINS 37
#define DATA_SAVE_TRIM 38
#define DATA_SAVEWP_ADD_WP 39
#define DATA_SAVEWP_CLEAR_MISSION_RTL 40
#define DATA_FENCE_ENABLE 41
#define DATA_FENCE_DISABLE 42
#define DATA_ACRO_TRAINER_DISABLED 43
#define DATA_ACRO_TRAINER_LEVELING 44
#define DATA_ACRO_TRAINER_LIMITED 45
#define DATA_EPM_GRAB 46
#define DATA_EPM_RELEASE 47
#define DATA_EPM_NEUTRAL 48 // deprecated
#define DATA_PARACHUTE_DISABLED 49
#define DATA_PARACHUTE_ENABLED 50
#define DATA_PARACHUTE_RELEASED 51
// Centi-degrees to radians
#define DEGX100 5729.57795f
// mark a function as not to be inlined
#define NOINLINE __attribute__((noinline))
// Error message sub systems and error codes
#define ERROR_SUBSYSTEM_MAIN 1
#define ERROR_SUBSYSTEM_RADIO 2
#define ERROR_SUBSYSTEM_COMPASS 3
#define ERROR_SUBSYSTEM_OPTFLOW 4
#define ERROR_SUBSYSTEM_FAILSAFE_RADIO 5
#define ERROR_SUBSYSTEM_FAILSAFE_BATT 6
#define ERROR_SUBSYSTEM_FAILSAFE_GPS 7
#define ERROR_SUBSYSTEM_FAILSAFE_GCS 8
#define ERROR_SUBSYSTEM_FAILSAFE_FENCE 9
#define ERROR_SUBSYSTEM_FLIGHT_MODE 10
#define ERROR_SUBSYSTEM_GPS 11
#define ERROR_SUBSYSTEM_CRASH_CHECK 12
#define ERROR_SUBSYSTEM_FLIP 13
#define ERROR_SUBSYSTEM_AUTOTUNE 14
#define ERROR_SUBSYSTEM_PARACHUTE 15
#define ERROR_SUBSYSTEM_EKFINAV_CHECK 16
#define ERROR_SUBSYSTEM_FAILSAFE_EKFINAV 17
#define ERROR_SUBSYSTEM_BARO 18
#define ERROR_SUBSYSTEM_CPU 19
// general error codes
#define ERROR_CODE_ERROR_RESOLVED 0
#define ERROR_CODE_FAILED_TO_INITIALISE 1
// subsystem specific error codes -- radio
#define ERROR_CODE_RADIO_LATE_FRAME 2
// subsystem specific error codes -- failsafe_thr, batt, gps
#define ERROR_CODE_FAILSAFE_RESOLVED 0
#define ERROR_CODE_FAILSAFE_OCCURRED 1
// subsystem specific error codes -- compass
#define ERROR_CODE_COMPASS_FAILED_TO_READ 2
// subsystem specific error codes -- gps
#define ERROR_CODE_GPS_GLITCH 2
// subsystem specific error codes -- main
#define ERROR_CODE_MAIN_INS_DELAY 1
// subsystem specific error codes -- crash checker
#define ERROR_CODE_CRASH_CHECK_CRASH 1
#define ERROR_CODE_CRASH_CHECK_LOSS_OF_CONTROL 2
// subsystem specific error codes -- flip
#define ERROR_CODE_FLIP_ABANDONED 2
// subsystem specific error codes -- autotune
#define ERROR_CODE_AUTOTUNE_BAD_GAINS 2
// parachute failed to deploy because of low altitude
#define ERROR_CODE_PARACHUTE_TOO_LOW 2
// EKF check definitions
#define ERROR_CODE_EKFINAV_CHECK_BAD_VARIANCE 2
#define ERROR_CODE_EKFINAV_CHECK_VARIANCE_CLEARED 0
// Baro specific error codes
#define ERROR_CODE_BARO_GLITCH 2
// Arming Check Enable/Disable bits
#define ARMING_CHECK_NONE 0x00
#define ARMING_CHECK_ALL 0x01
#define ARMING_CHECK_BARO 0x02
#define ARMING_CHECK_COMPASS 0x04
#define ARMING_CHECK_GPS 0x08
#define ARMING_CHECK_INS 0x10
#define ARMING_CHECK_PARAMETERS 0x20
#define ARMING_CHECK_RC 0x40
#define ARMING_CHECK_VOLTAGE 0x80
// Radio failsafe definitions (FS_THR parameter)
#define FS_THR_DISABLED 0
#define FS_THR_ENABLED_ALWAYS_RTL 1
#define FS_THR_ENABLED_CONTINUE_MISSION 2
#define FS_THR_ENABLED_ALWAYS_LAND 3
// Battery failsafe definitions (FS_BATT_ENABLE parameter)
#define FS_BATT_DISABLED 0 // battery failsafe disabled
#define FS_BATT_LAND 1 // switch to LAND mode on battery failsafe
#define FS_BATT_RTL 2 // switch to RTL mode on battery failsafe
// GPS Failsafe definitions (FS_GPS_ENABLE parameter)
#define FS_GPS_DISABLED 0 // GPS failsafe disabled
#define FS_GPS_LAND 1 // switch to LAND mode on GPS Failsafe
#define FS_GPS_ALTHOLD 2 // switch to ALTHOLD mode on GPS failsafe
#define FS_GPS_LAND_EVEN_STABILIZE 3 // switch to LAND mode on GPS failsafe even if in a manual flight mode like Stabilize
// for mavlink SET_POSITION_TARGET messages
#define MAVLINK_SET_POS_TYPE_MASK_POS_IGNORE ((1<<0) | (1<<1) | (1<<2))
#define MAVLINK_SET_POS_TYPE_MASK_VEL_IGNORE ((1<<3) | (1<<4) | (1<<5))
#define MAVLINK_SET_POS_TYPE_MASK_ACC_IGNORE ((1<<6) | (1<<7) | (1<<8))
#define MAVLINK_SET_POS_TYPE_MASK_FORCE (1<<10)
#define MAVLINK_SET_POS_TYPE_MASK_YAW_IGNORE (1<<11)
#define MAVLINK_SET_POS_TYPE_MASK_YAW_RATE_IGNORE (1<<12)
enum Serial2Protocol {
SERIAL2_MAVLINK = 1,
SERIAL2_FRSKY_DPORT = 2,
SERIAL2_FRSKY_SPORT = 3 // not supported yet
};
#endif // _DEFINES_H