zr-v4/ArduCopter/mode_zigzag.cpp

#include "Copter.h"

#if MODE_ZIGZAG_ENABLED == ENABLED

/*
* Init and run calls for zigzag flight mode
*/

#define ZIGZAG_WP_RADIUS_CM 300

// initialise zigzag controller
bool ModeZigZag::init(bool ignore_checks)
{
    // initialize's loiter position and velocity on xy-axes from current pos and velocity
    loiter_nav->clear_pilot_desired_acceleration();
    loiter_nav->init_target();

    // initialise position_z and desired velocity_z
    if (!pos_control->is_active_z()) {
        pos_control->set_alt_target_to_current_alt();
        pos_control->set_desired_velocity_z(inertial_nav.get_velocity_z());
    }

    // initialise waypoint state
    stage = STORING_POINTS;
    dest_A.zero();
    dest_B.zero();

    return true;
}

// run the zigzag controller
// should be called at 100hz or more
void ModeZigZag::run()
{
    // initialize vertical speed and acceleration's range
    pos_control->set_max_speed_z(-get_pilot_speed_dn(), g.pilot_speed_up);
    pos_control->set_max_accel_z(g.pilot_accel_z);

    // if not auto armed or motors not enabled set throttle to zero and exit immediately
    if (is_disarmed_or_landed() || !motors->get_interlock() ) {
        zero_throttle_and_relax_ac(copter.is_tradheli() && motors->get_interlock());
        return;
    }

    // auto control
    if (stage == AUTO) {
        // if vehicle has reached destination switch to manual control
        if (reached_destination()) {
            AP_Notify::events.waypoint_complete = 1;
            return_to_manual_control(true);
        } else {
            auto_control();
        }
    }

    // manual control
    if (stage == STORING_POINTS || stage == MANUAL_REGAIN) {
        // receive pilot's inputs, do position and attitude control
        manual_control();
    }
}

// save current position as A (dest_num = 0) or B (dest_num = 1).  If both A and B have been saved move to the one specified
void ModeZigZag::save_or_move_to_destination(uint8_t dest_num)
{
    // sanity check
    if (dest_num > 1) {
        return;
    }

    // get current position as an offset from EKF origin
    const Vector3f curr_pos = inertial_nav.get_position();

    // handle state machine changes
    switch (stage) {

        case STORING_POINTS:
            if (dest_num == 0) {
                // store point A
                dest_A.x = curr_pos.x;
                dest_A.y = curr_pos.y;
                gcs().send_text(MAV_SEVERITY_INFO, "ZigZag: point A stored");
                copter.Log_Write_Event(DATA_ZIGZAG_STORE_A);
            } else {
                // store point B
                dest_B.x = curr_pos.x;
                dest_B.y = curr_pos.y;
                gcs().send_text(MAV_SEVERITY_INFO, "ZigZag: point B stored");
                copter.Log_Write_Event(DATA_ZIGZAG_STORE_B);
            }
            // if both A and B have been stored advance state
            if (!dest_A.is_zero() && !dest_B.is_zero() && is_positive((dest_B - dest_A).length_squared())) {
                stage = MANUAL_REGAIN;
            }
            break;

        case AUTO:
        case MANUAL_REGAIN:
            // A and B have been defined, move vehicle to destination A or B
            Vector3f next_dest;
            bool terr_alt;
            if (calculate_next_dest(dest_num, stage == AUTO, next_dest, terr_alt)) {
                wp_nav->wp_and_spline_init();
                if (wp_nav->set_wp_destination(next_dest, terr_alt)) {
                    stage = AUTO;
                    reach_wp_time_ms = 0;
                    if (dest_num == 0) {
                        gcs().send_text(MAV_SEVERITY_INFO, "ZigZag: moving to A");
                    } else {
                        gcs().send_text(MAV_SEVERITY_INFO, "ZigZag: moving to B");
                    }
                }
            }
            break;
    }
}

// return manual control to the pilot
void ModeZigZag::return_to_manual_control(bool maintain_target)
{
    if (stage == AUTO) {
        stage = MANUAL_REGAIN;
        loiter_nav->clear_pilot_desired_acceleration();
        if (maintain_target) {
            const Vector3f wp_dest = wp_nav->get_wp_destination();
            loiter_nav->init_target(wp_dest);
            if (wp_nav->origin_and_destination_are_terrain_alt()) {
                copter.surface_tracking.set_target_alt_cm(wp_dest.z);
            }
        } else {
            loiter_nav->init_target();
        }
        gcs().send_text(MAV_SEVERITY_INFO, "ZigZag: manual control");
    }
}

// fly the vehicle to closest point on line perpendicular to dest_A or dest_B
void ModeZigZag::auto_control()
{
    // process pilot's yaw input
    float target_yaw_rate = 0;
    if (!copter.failsafe.radio) {
        // get pilot's desired yaw rate
        target_yaw_rate = get_pilot_desired_yaw_rate(channel_yaw->get_control_in());
    }

    // set motors to full range
    motors->set_desired_spool_state(AP_Motors::DesiredSpoolState::THROTTLE_UNLIMITED);

    // run waypoint controller
    const bool wpnav_ok = wp_nav->update_wpnav();

    // call z-axis position controller (wp_nav should have already updated its alt target)
    pos_control->update_z_controller();

    // call attitude controller
    // roll & pitch from waypoint controller, yaw rate from pilot
    attitude_control->input_euler_angle_roll_pitch_euler_rate_yaw(wp_nav->get_roll(), wp_nav->get_pitch(), target_yaw_rate);

    // if wpnav failed (because of lack of terrain data) switch back to pilot control for next iteration
    if (!wpnav_ok) {
        return_to_manual_control(false);
    }
}

// manual_control - process manual control
void ModeZigZag::manual_control()
{
    float target_yaw_rate = 0.0f;
    float target_climb_rate = 0.0f;

    // process pilot inputs unless we are in radio failsafe
    if (!copter.failsafe.radio) {
        float target_roll, target_pitch;
        // apply SIMPLE mode transform to pilot inputs
        update_simple_mode();

        // convert pilot input to lean angles
        get_pilot_desired_lean_angles(target_roll, target_pitch, loiter_nav->get_angle_max_cd(), attitude_control->get_althold_lean_angle_max());

        // process pilot's roll and pitch input
        loiter_nav->set_pilot_desired_acceleration(target_roll, target_pitch, G_Dt);
        // get pilot's desired yaw rate
        target_yaw_rate = get_pilot_desired_yaw_rate(channel_yaw->get_control_in());

        // get pilot desired climb rate
        target_climb_rate = get_pilot_desired_climb_rate(channel_throttle->get_control_in());
        // make sure the climb rate is in the given range, prevent floating point errors
        target_climb_rate = constrain_float(target_climb_rate, -get_pilot_speed_dn(), g.pilot_speed_up);
    } else {
        // clear out pilot desired acceleration in case radio failsafe event occurs and we
        // do not switch to RTL for some reason
        loiter_nav->clear_pilot_desired_acceleration();
    }

    // set motors to full range
    motors->set_desired_spool_state(AP_Motors::DesiredSpoolState::THROTTLE_UNLIMITED);

    // run loiter controller
    loiter_nav->update();

    // call attitude controller
    attitude_control->input_euler_angle_roll_pitch_euler_rate_yaw(loiter_nav->get_roll(), loiter_nav->get_pitch(), target_yaw_rate);

    // adjust climb rate using rangefinder
    target_climb_rate = copter.surface_tracking.adjust_climb_rate(target_climb_rate);

    // get avoidance adjusted climb rate
    target_climb_rate = get_avoidance_adjusted_climbrate(target_climb_rate);

    // update altitude target and call position controller
    pos_control->set_alt_target_from_climb_rate_ff(target_climb_rate, G_Dt, false);

    // adjusts target up or down using a climb rate
    pos_control->update_z_controller();
}

// return true if vehicle is within a small area around the destination
bool ModeZigZag::reached_destination()
{
    // check if wp_nav believes it has reached the destination
    if (!wp_nav->reached_wp_destination()) {
        return false;
    }

    // check distance to destination
    if (wp_nav->get_wp_distance_to_destination() > ZIGZAG_WP_RADIUS_CM) {
        return false;
    }

    // wait at least one second
    uint32_t now = AP_HAL::millis();
    if (reach_wp_time_ms == 0) {
        reach_wp_time_ms = now;
    }
    return ((now - reach_wp_time_ms) > 1000);
}

// calculate next destination according to vector A-B and current position
// use_wpnav_alt should be true if waypoint controller's altitude target should be used, false for position control or current altitude target
// terrain_alt is returned as true if the next_dest should be considered a terrain alt
bool ModeZigZag::calculate_next_dest(uint8_t dest_num, bool use_wpnav_alt, Vector3f& next_dest, bool& terrain_alt) const
{
    // sanity check dest_num
    if (dest_num > 1) {
        return false;
    }

    // define start_pos as either A or B depending upon dest_num
    Vector2f start_pos = dest_num == 0 ? dest_A : dest_B;

    // calculate vector from A to B
    Vector2f AB_diff = dest_B - dest_A;

    // check distance between A and B
    if (!is_positive(AB_diff.length_squared())) {
        return false;
    }

    // get distance from vehicle to start_pos
    const Vector3f curr_pos = inertial_nav.get_position();
    const Vector2f curr_pos2d = Vector2f(curr_pos.x, curr_pos.y);
    Vector2f veh_to_start_pos = curr_pos2d - start_pos;

    // lengthen AB_diff so that it is at least as long as vehicle is from start point
    // we need to ensure that the lines perpendicular to AB are long enough to reach the vehicle
    float scalar = 1.0f;
    if (veh_to_start_pos.length_squared() > AB_diff.length_squared()) {
        scalar = veh_to_start_pos.length() / AB_diff.length();
    }

    // create a line perpendicular to AB but originating at start_pos
    Vector2f perp1 = start_pos + Vector2f(-AB_diff[1] * scalar, AB_diff[0] * scalar);
    Vector2f perp2 = start_pos + Vector2f(AB_diff[1] * scalar, -AB_diff[0] * scalar);

    // find the closest point on the perpendicular line
    const Vector2f closest2d = Vector2f::closest_point(curr_pos2d, perp1, perp2);
    next_dest.x = closest2d.x;
    next_dest.y = closest2d.y;

    if (use_wpnav_alt) {
        // get altitude target from waypoint controller
        terrain_alt = wp_nav->origin_and_destination_are_terrain_alt();
        next_dest.z = wp_nav->get_wp_destination().z;
    } else {
        // if we have a downward facing range finder then use terrain altitude targets
        terrain_alt = copter.rangefinder_alt_ok() && wp_nav->rangefinder_used();
        if (terrain_alt) {
            if (!copter.surface_tracking.get_target_alt_cm(next_dest.z)) {
                next_dest.z = copter.rangefinder_state.alt_cm_filt.get();
            }
        } else {
            next_dest.z = pos_control->is_active_z() ? pos_control->get_alt_target() : curr_pos.z;
        }
    }

    return true;
}

#endif // MODE_ZIGZAG_ENABLED == ENABLED