zr-v4/libraries/AP_AHRS/AP_AHRS_MPU6000.cpp

/// -*- tab-width: 4; Mode: C++; c-basic-offset: 4; indent-tabs-mode: nil -*-
/*
 *       AP_AHRS_MPU6000.cpp
 *
 *       AHRS system using MPU6000's internal calculations
 *
 *       Adapted for the general ArduPilot AHRS interface by Andrew Tridgell
 *
 *       This library is free software; you can redistribute it and/or
 *       modify it under the terms of the GNU Lesser General Public License
 *       as published by the Free Software Foundation; either version 2.1
 *       of the License, or (at your option) any later version.
 */
#include <AP_AHRS.h>
#include <AP_HAL.h>

extern const AP_HAL::HAL& hal;

// this is the speed in cm/s above which we first get a yaw lock with
// the GPS
#define GPS_SPEED_MIN 300

// this is the speed in cm/s at which we stop using drift correction
// from the GPS and wait for the ground speed to get above GPS_SPEED_MIN
#define GPS_SPEED_RESET 100

// the limit (in degrees/second) beyond which we stop integrating
// omega_I. At larger spin rates the DCM PI controller can get 'dizzy'
// which results in false gyro drift. See
// http://gentlenav.googlecode.com/files/fastRotations.pdf
#define SPIN_RATE_LIMIT 20

void
AP_AHRS_MPU6000::init()
{
    // call parent init
    AP_AHRS::init();

    // suspend timer so interrupts on spi bus do not interfere with
    // communication to mpu6000
    hal.scheduler->suspend_timer_procs();

    _mpu6000->dmp_init();
    push_gains_to_dmp();
    _mpu6000->push_gyro_offsets_to_dmp();

    // restart timer
    hal.scheduler->resume_timer_procs();
};

// run a full MPU6000 update round
void
AP_AHRS_MPU6000::update(void)
{
    float delta_t;

    // tell the IMU to grab some data.
    if( !_secondary_ahrs ) {
        _ins->update();
    }

    // ask the IMU how much time this sensor reading represents
    delta_t = _ins->get_delta_time();

    // convert the quaternions into a DCM matrix
    _mpu6000->quaternion.rotation_matrix(_dcm_matrix);

    // we run the gyro bias correction using gravity vector algorithm
    drift_correction(delta_t);

    // Calculate pitch, roll, yaw for stabilization and navigation
    euler_angles();

    // prepare earth frame accelerometer values for ArduCopter Inertial Navigation and accel-based throttle
    _accel_ef = _dcm_matrix * _ins->get_accel();
}

// wrap_PI - ensure an angle (expressed in radians) is between -PI and PI
// TO-DO: should remove and replace with more standard functions
float AP_AHRS_MPU6000::wrap_PI(float angle_in_radians)
{
    if( angle_in_radians > PI ) {
        return(angle_in_radians - 2*PI);
    }
    else if( angle_in_radians < -PI ) {
        return(angle_in_radians + 2*PI);
    }
    else{
        return(angle_in_radians);
    }
}

// Function to correct the gyroX and gyroY bias (roll and pitch) using the
// gravity vector from accelerometers We use the internal chip axis definition
// to make the bias correction because both sensors outputs (gyros and accels)
// are in chip axis definition
void AP_AHRS_MPU6000::drift_correction( float deltat )
{
    float errorRollPitch[2];

    // Get current values for gyros
    _accel_vector = _ins->get_accel();

    // We take the accelerometer readings and cumulate to average them and
    // obtain the gravity vector
    _accel_filtered += _accel_vector;
    _accel_filtered_samples++;

    _gyro_bias_from_gravity_counter++;
    // We make the bias calculation and correction at a lower rate
    // (GYRO_BIAS_FROM_GRAVITY_RATE)
    if( _gyro_bias_from_gravity_counter == GYRO_BIAS_FROM_GRAVITY_RATE ) {
        _gyro_bias_from_gravity_counter = 0;

        _accel_filtered /= _accel_filtered_samples;          // average

        // Adjust ground reference : Accel Cross Gravity to obtain the error
        // between gravity from accels and gravity from attitude solution
        // errorRollPitch are in Accel LSB units
        errorRollPitch[0] = _accel_filtered.y * _dcm_matrix.c.z
            + _accel_filtered.z * _dcm_matrix.c.x;
        errorRollPitch[1] = -_accel_filtered.z * _dcm_matrix.c.y
            - _accel_filtered.x * _dcm_matrix.c.z;

        errorRollPitch[0] *= deltat * 1000;
        errorRollPitch[1] *= deltat * 1000;

        // we limit to maximum gyro drift rate on each axis
        // 0.65*0.04 / 0.005 = 5.2
        float drift_limit = _mpu6000->get_gyro_drift_rate() * deltat 
            / _gyro_bias_from_gravity_gain;
        errorRollPitch[0] = constrain(errorRollPitch[0],
                -drift_limit, drift_limit);
        errorRollPitch[1] = constrain(errorRollPitch[1],
                -drift_limit, drift_limit);

        // We correct gyroX and gyroY bias using the error vector
        _gyro_bias[0] += errorRollPitch[0]*_gyro_bias_from_gravity_gain;
        _gyro_bias[1] += errorRollPitch[1]*_gyro_bias_from_gravity_gain;

        // TO-DO: fix this.  Currently it makes the roll and pitch drift more!
        // If bias values are greater than 1 LSB we update the hardware offset
        // registers
        if( fabsf(_gyro_bias[0])>1.0f ) {
            //_mpu6000->set_gyro_offsets(-1*(int)_gyro_bias[0],0,0);
            //_mpu6000->set_gyro_offsets(0,-1*(int)_gyro_bias[0],0);
            //_gyro_bias[0] -= (int)_gyro_bias[0];  // we remove the part that
            // we have already corrected on registers...
        }
        if (fabsf(_gyro_bias[1])>1.0f) {
            //_mpu6000->set_gyro_offsets(-1*(int)_gyro_bias[1],0,0);
            //_gyro_bias[1] -= (int)_gyro_bias[1];
        }

        // Reset the accelerometer variables
        _accel_filtered.x = 0;
        _accel_filtered.y = 0;
        _accel_filtered.z = 0;
        _accel_filtered_samples=0;
    }

    // correct the yaw
    drift_correction_yaw();
}


/*
 *  reset the DCM matrix and omega. Used on ground start, and on
 *  extreme errors in the matrix
 */
void
AP_AHRS_MPU6000::reset(bool recover_eulers)
{
    // if the caller wants us to try to recover to the current
    // attitude then calculate the dcm matrix from the current
    // roll/pitch/yaw values
    if (recover_eulers && !isnan(roll) && !isnan(pitch) && !isnan(yaw)) {
        _dcm_matrix.from_euler(roll, pitch, yaw);
    } else {
        // otherwise make it flat
        _dcm_matrix.from_euler(0, 0, 0);
    }
}

// push offsets down from IMU to INS (required so MPU6000 can perform it's own
// attitude estimation)
void
AP_AHRS_MPU6000::push_offsets_to_ins()
{
    // push down gyro offsets (TO-DO: why are x and y offsets are reversed?!)
    _mpu6000->push_gyro_offsets_to_dmp();

    // push down accelerometer offsets
    // (TO-DO: why are x and y offsets are reversed?!)
    _mpu6000->push_accel_offsets_to_dmp();
}

void
AP_AHRS_MPU6000::push_gains_to_dmp()
{
    uint8_t gain;
    if( _kp.get() >= 1.0f ) {
        gain = 0xFF;
    }else if( _kp.get() <= 0.0f ) {
        gain = 0x00;
    }else{
        gain = (uint8_t)((float)0xFF * _kp.get());
    }

    _mpu6000->dmp_set_sensor_fusion_accel_gain(gain);
}

// produce a yaw error value. The returned value is proportional
// to sin() of the current heading error in earth frame
float
AP_AHRS_MPU6000::yaw_error_compass(void)
{
    Vector3f mag = Vector3f(_compass->mag_x, _compass->mag_y, _compass->mag_z);
    // get the mag vector in the earth frame
    Vector3f rb = _dcm_matrix * mag;

    rb.normalize();
    if (rb.is_inf()) {
        // not a valid vector
        return 0.0;
    }

    // get the earths magnetic field (only X and Y components needed)
    Vector3f mag_earth = Vector3f(cosf(_compass->get_declination()),
                                  sinf(_compass->get_declination()), 0);

    // calculate the error term in earth frame
    Vector3f error = rb % mag_earth;

    return error.z;
}

//
// drift_correction_yaw - yaw drift correction using the compass
//    we have no way to update the dmp with it's actual heading from our
//    compass instead we use the yaw_corrected variable to hold what we think
//    is the real heading we also record what the dmp said it's last heading
//    was in the yaw_last_uncorrected variable so that on the next iteration we
//    can add the change in yaw to our estimate
//
void
AP_AHRS_MPU6000::drift_correction_yaw(void)
{
    static float yaw_corrected = HEADING_UNKNOWN;
    static float last_dmp_yaw = HEADING_UNKNOWN;
    // roll pitch and yaw values from dmp
    float dmp_roll, dmp_pitch, dmp_yaw;
    // change in yaw according to dmp
    float yaw_delta;
    // difference between heading and corrected yaw
    float yaw_error;
    static float heading;

    // get uncorrected yaw values from dmp
    _mpu6000->quaternion.to_euler(&dmp_roll, &dmp_pitch, &dmp_yaw);

    // initialise headings on first iteration
    if( yaw_corrected == HEADING_UNKNOWN ) {
        yaw_corrected = dmp_yaw;
        last_dmp_yaw = dmp_yaw;
    }

    // change in yaw according to dmp
    yaw_delta = wrap_PI(dmp_yaw - last_dmp_yaw);
    yaw_corrected = wrap_PI(yaw_corrected + yaw_delta);
    last_dmp_yaw = dmp_yaw;

    // rebuild dcm matrix
    _dcm_matrix.from_euler(dmp_roll, dmp_pitch, yaw_corrected);

    // if we have new compass data
    if(_compass && _compass->use_for_yaw() ) {
        if(_compass->last_update != _compass_last_update) {
            _compass_last_update = _compass->last_update;
            heading = _compass->calculate_heading(_dcm_matrix);

            // if this is the first good compass reading then set yaw to this heading
            if( !_have_initial_yaw ) {
                _have_initial_yaw = true;
                yaw_corrected = wrap_PI(heading);
            }

            // yaw correction based on compass
            //yaw_error = yaw_error_compass();
            yaw_error = wrap_PI(heading - yaw_corrected);

            // shift the corrected yaw towards the compass heading a bit
            yaw_corrected += wrap_PI(yaw_error * _kp_yaw.get() * 0.1f);

            // rebuild the dcm matrix yet again
            _dcm_matrix.from_euler(dmp_roll, dmp_pitch, yaw_corrected);
        }
    }
}

// calculate the euler angles which will be used for high level
// navigation control
void
AP_AHRS_MPU6000::euler_angles(void)
{
    _dcm_matrix.to_euler(&roll, &pitch, &yaw);
    // cannot use this because the quaternion is not correct for yaw drift
    //quaternion.to_euler(&roll, &pitch, &yaw);

    roll_sensor     = degrees(roll)  * 100;
    pitch_sensor    = degrees(pitch) * 100;
    yaw_sensor              = degrees(yaw)   * 100;

    if (yaw_sensor < 0)
        yaw_sensor += 36000;
}

/* reporting of DCM state for MAVLink */

// average error_roll_pitch since last call
float AP_AHRS_MPU6000::get_error_rp(void)
{
    // not yet supported with DMP
    return 0.0;
}

// average error_yaw since last call
float AP_AHRS_MPU6000::get_error_yaw(void)
{
    // not yet supported with DMP
    return 0.0;
}