| .. |
|
Frame
|
move Frame into ArduCopter
|
14 years ago |
|
.gitignore
|
Improvements to cmake.
|
14 years ago |
|
APM_Config.h
|
Enabled auto throttle hold
|
13 years ago |
|
APM_Config_mavlink_hil.h
|
removed airspeed
|
13 years ago |
|
ArduCopter.pde
|
changed tuning range
|
13 years ago |
|
Attitude.pde
|
OpticalFlow - replaced PI controller with PID controller.
|
13 years ago |
|
Camera.pde
|
ArduCopter: Call APM_RC.enable_out for camera channels in init_camera()
|
13 years ago |
|
GCS.h
|
USB-MUX: enable USB MUX switching for ArduCopter
|
13 years ago |
|
GCS.pde
|
renamed top level directories
|
14 years ago |
|
GCS_Mavlink copy.txt
|
added conversions of CM to M
|
13 years ago |
|
GCS_Mavlink.pde
|
Causes Aero_SIM to fail
|
13 years ago |
|
Log.pde
|
recording nav_bearing rather than target bearing
|
13 years ago |
|
Makefile
|
sitl: added build targets for different ACM frames
|
13 years ago |
|
Parameters.h
|
OpticalFlow - replaced PI controller with PID controller.
|
13 years ago |
|
UserCode.pde
|
Added Andrew's user hooks.
|
14 years ago |
|
UserVariables.h
|
Added Andrew's user hooks.
|
14 years ago |
|
command description.txt
|
renamed top level directories
|
14 years ago |
|
commands.pde
|
better default for speed governer
|
13 years ago |
|
commands_logic.pde
|
convert command into CM from M
|
13 years ago |
|
commands_process.pde
|
error on comparison operator
|
13 years ago |
|
config.h
|
OpticalFlow - added OF_LOITER flightmode
|
13 years ago |
|
config_channels.h
|
ArduCopter Tri: fix for enable_out of yaw servo, defined yaw servo for APM2
|
13 years ago |
|
control_modes.pde
|
relocated reset_I term functions to central location
|
13 years ago |
|
defines.h
|
OpticalFlow - added OF_LOITER flightmode
|
13 years ago |
|
events.pde
|
added set_new_altitude call()
|
13 years ago |
|
flip.pde
|
Fixed Flip code to compile. Flip still not flight tested!
|
14 years ago |
|
heli.pde
|
ArduCopter Heli: add motors_output_enable function
|
13 years ago |
|
leds.pde
|
ACM: use LED_OFF/LED_ON instead of LOW/HIGH
|
13 years ago |
|
motors.pde
|
reset all I terms at Arming
|
13 years ago |
|
motors_hexa.pde
|
ArduCopter: Add implementation of motors_output_enable to each motors_ frame type
|
13 years ago |
|
motors_octa.pde
|
ArduCopter: Add implementation of motors_output_enable to each motors_ frame type
|
13 years ago |
|
motors_octa_quad.pde
|
ArduCopter: Add implementation of motors_output_enable to each motors_ frame type
|
13 years ago |
|
motors_quad.pde
|
ArduCopter: Add implementation of motors_output_enable to each motors_ frame type
|
13 years ago |
|
motors_tri.pde
|
ArduCopter Tri: fix for enable_out of yaw servo, defined yaw servo for APM2
|
13 years ago |
|
motors_y6.pde
|
ArduCopter: Add implementation of motors_output_enable to each motors_ frame type
|
13 years ago |
|
navigation.pde
|
added loiter_d to allow users to configure alternate Loiter alg
|
13 years ago |
|
planner.pde
|
Stability patch updates,
|
13 years ago |
|
radio.pde
|
Arducopter - Tri - move yaw servo (channel7/motor7/CH_TRI_YAW) to mid point on startup
|
13 years ago |
|
read_me.text
|
renamed top level directories
|
14 years ago |
|
sensors.pde
|
Optical flow - updated standard frame rate to 2000hz and increased resolution to 1600cpi
|
13 years ago |
|
setup.pde
|
ArduCopter: Call motors_output_enable at correct spot during init
|
13 years ago |
|
system.pde
|
OpticalFlow - added OF_LOITER flightmode
|
13 years ago |
|
test.pde
|
Update battery monitoring code for ArduCopter
|
13 years ago |
Jason Short
326a663c6b