You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
74 lines
2.9 KiB
74 lines
2.9 KiB
// -*- tab-width: 4; Mode: C++; c-basic-offset: 4; indent-tabs-mode: nil -*- |
|
|
|
/// @file AP_MotorsCoax.h |
|
/// @brief Motor and Servo control class for Co-axial helicopters with two motors and two flaps |
|
|
|
#ifndef __AP_MOTORS_COAX_H__ |
|
#define __AP_MOTORS_COAX_H__ |
|
|
|
#include <AP_Common.h> |
|
#include <AP_Math.h> // ArduPilot Mega Vector/Matrix math Library |
|
#include <RC_Channel.h> // RC Channel Library |
|
#include "AP_Motors.h" |
|
|
|
// feedback direction |
|
#define AP_MOTORS_COAX_POSITIVE 1 |
|
#define AP_MOTORS_COAX_NEGATIVE -1 |
|
|
|
#define AP_MOTORS_SINGLE_SPEED_DIGITAL_SERVOS 250 // update rate for digital servos |
|
#define AP_MOTORS_SINGLE_SPEED_ANALOG_SERVOS 125 // update rate for analog servos |
|
|
|
#define AP_MOTORS_COAX_SERVO_INPUT_RANGE 4500 // roll or pitch input of -4500 will cause servos to their minimum (i.e. radio_min), +4500 will move them to their maximum (i.e. radio_max) |
|
|
|
/// @class AP_MotorsSingle |
|
class AP_MotorsCoax : public AP_Motors { |
|
public: |
|
|
|
/// Constructor |
|
AP_MotorsCoax( RC_Channel& rc_roll, RC_Channel& rc_pitch, RC_Channel& rc_throttle, RC_Channel& rc_yaw, RC_Channel& servo1, RC_Channel& servo2, uint16_t loop_rate, uint16_t speed_hz = AP_MOTORS_SPEED_DEFAULT) : |
|
AP_Motors(rc_roll, rc_pitch, rc_throttle, rc_yaw, loop_rate, speed_hz), |
|
_servo1(servo1), |
|
_servo2(servo2) |
|
{ |
|
AP_Param::setup_object_defaults(this, var_info); |
|
}; |
|
|
|
// init |
|
virtual void Init(); |
|
|
|
// set update rate to motors - a value in hertz |
|
void set_update_rate( uint16_t speed_hz ); |
|
|
|
// enable - starts allowing signals to be sent to motors |
|
virtual void enable(); |
|
|
|
// output_test - spin a motor at the pwm value specified |
|
// motor_seq is the motor's sequence number from 1 to the number of motors on the frame |
|
// pwm value is an actual pwm value that will be output, normally in the range of 1000 ~ 2000 |
|
virtual void output_test(uint8_t motor_seq, int16_t pwm); |
|
|
|
// output_min - sends minimum values out to the motors |
|
virtual void output_min(); |
|
|
|
// get_motor_mask - returns a bitmask of which outputs are being used for motors or servos (1 means being used) |
|
// this can be used to ensure other pwm outputs (i.e. for servos) do not conflict |
|
// for coax copter, output channels 1 to 4 are used |
|
virtual uint16_t get_motor_mask() { return 0x000F; } |
|
|
|
// var_info for holding Parameter information |
|
static const struct AP_Param::GroupInfo var_info[]; |
|
|
|
protected: |
|
// output - sends commands to the motors |
|
virtual void output_armed(); |
|
virtual void output_disarmed(); |
|
|
|
AP_Int8 _rev_roll; // REV Roll feedback |
|
AP_Int8 _rev_pitch; // REV pitch feedback |
|
AP_Int8 _rev_yaw; // REV yaw feedback |
|
AP_Int16 _servo_speed; // servo speed |
|
RC_Channel& _servo1; |
|
RC_Channel& _servo2; |
|
}; |
|
|
|
#endif // AP_MOTORSCOAX
|
|
|