You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
75 lines
3.0 KiB
75 lines
3.0 KiB
/// -*- tab-width: 4; Mode: C++; c-basic-offset: 4; indent-tabs-mode: nil -*- |
|
|
|
#include "Copter.h" |
|
|
|
#if FRAME_CONFIG == HELI_FRAME |
|
/* |
|
* heli_control_acro.pde - init and run calls for acro flight mode for trad heli |
|
*/ |
|
|
|
// heli_acro_init - initialise acro controller |
|
bool Copter::heli_acro_init(bool ignore_checks) |
|
{ |
|
// if heli is equipped with a flybar, then tell the attitude controller to pass through controls directly to servos |
|
attitude_control.use_flybar_passthrough(motors.has_flybar(), motors.tail_type() == AP_MOTORS_HELI_TAILTYPE_SERVO_EXTGYRO); |
|
|
|
// always successfully enter acro |
|
return true; |
|
} |
|
|
|
// heli_acro_run - runs the acro controller |
|
// should be called at 100hz or more |
|
void Copter::heli_acro_run() |
|
{ |
|
float target_roll, target_pitch, target_yaw; |
|
|
|
// Tradheli should not reset roll, pitch, yaw targets when motors are not runup, because |
|
// we may be in autorotation flight. These should be reset only when transitioning from disarmed |
|
// to armed, because the pilot will have placed the helicopter down on the landing pad. This is so |
|
// that the servos move in a realistic fashion while disarmed for operational checks. |
|
// Also, unlike multicopters we do not set throttle (i.e. collective pitch) to zero so the swash servos move |
|
|
|
if(!motors.armed()) { |
|
heli_flags.init_targets_on_arming=true; |
|
attitude_control.set_yaw_target_to_current_heading(); |
|
} |
|
|
|
if(motors.armed() && heli_flags.init_targets_on_arming) { |
|
attitude_control.relax_bf_rate_controller(); |
|
attitude_control.set_yaw_target_to_current_heading(); |
|
if (motors.rotor_speed_above_critical()) { |
|
heli_flags.init_targets_on_arming=false; |
|
} |
|
} |
|
|
|
// send RC inputs direct into motors library for use during manual passthrough for helicopter setup |
|
heli_radio_passthrough(); |
|
|
|
if (!motors.has_flybar()){ |
|
// convert the input to the desired body frame rate |
|
get_pilot_desired_angle_rates(channel_roll->control_in, channel_pitch->control_in, channel_yaw->control_in, target_roll, target_pitch, target_yaw); |
|
// run attitude controller |
|
attitude_control.rate_bf_roll_pitch_yaw(target_roll, target_pitch, target_yaw); |
|
}else{ |
|
// flybar helis only need yaw rate control |
|
get_pilot_desired_yaw_rate(channel_yaw->control_in, target_yaw); |
|
// run attitude controller |
|
attitude_control.passthrough_bf_roll_pitch_rate_yaw(channel_roll->control_in, channel_pitch->control_in, target_yaw); |
|
} |
|
|
|
// output pilot's throttle without angle boost |
|
attitude_control.set_throttle_out(channel_throttle->control_in, false, g.throttle_filt); |
|
} |
|
|
|
// get_pilot_desired_yaw_rate - transform pilot's yaw input into a desired yaw angle rate |
|
// returns desired yaw rate in centi-degrees-per-second |
|
void Copter::get_pilot_desired_yaw_rate(int16_t yaw_in, float &yaw_out) |
|
{ |
|
// calculate rate request |
|
float rate_bf_yaw_request = yaw_in * g.acro_yaw_p; |
|
|
|
// hand back rate request |
|
yaw_out = rate_bf_yaw_request; |
|
} |
|
|
|
#endif //HELI_FRAME
|
|
|