You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
147 lines
2.9 KiB
147 lines
2.9 KiB
# hw definition file for processing by chibios_pins.py |
|
|
|
# MCU class and specific type |
|
MCU STM32F103 STM32F103xB |
|
|
|
# bootloader starts firmware at 25k |
|
FLASH_RESERVE_START_KB 25 |
|
|
|
# store parameters in pages 23 and 24 |
|
define STORAGE_FLASH_PAGE 23 |
|
define HAL_STORAGE_SIZE 800 |
|
|
|
# board ID for firmware load |
|
APJ_BOARD_ID 1000 |
|
|
|
# setup build for a peripheral firmware |
|
env AP_PERIPH 1 |
|
|
|
# crystal frequency |
|
OSCILLATOR_HZ 8000000 |
|
|
|
define CH_CFG_ST_FREQUENCY 1000 |
|
|
|
# assume the 128k flash part for now |
|
FLASH_SIZE_KB 128 |
|
|
|
# board voltage |
|
STM32_VDD 330U |
|
|
|
# order of UARTs |
|
UART_ORDER USART2 USART1 |
|
|
|
# a LED to flash |
|
PA4 LED OUTPUT LOW |
|
|
|
# USART1, connected to GPS |
|
PA9 USART1_TX USART1 SPEED_HIGH NODMA |
|
PA10 USART1_RX USART1 SPEED_HIGH NODMA |
|
|
|
# USART2 for debug |
|
PA2 USART2_TX USART2 SPEED_HIGH NODMA |
|
PA3 USART2_RX USART2 SPEED_HIGH NODMA |
|
|
|
define HAL_UART_NODMA |
|
|
|
# only one I2C bus in normal config |
|
PB6 I2C1_SCL I2C1 |
|
PB7 I2C1_SDA I2C1 |
|
|
|
PB0 MAG_CS CS |
|
|
|
# spi bus for compass |
|
PA5 SPI1_SCK SPI1 |
|
PA6 SPI1_MISO SPI1 |
|
PA7 SPI1_MOSI SPI1 |
|
|
|
SPIDEV rm3100 SPI1 DEVID1 MAG_CS MODE0 1*MHZ 1*MHZ |
|
|
|
# analog input |
|
# PA5 VIN5 ADC1 |
|
define HAL_USE_ADC TRUE |
|
define STM32_ADC_USE_ADC1 TRUE |
|
define HAL_DISABLE_ADC_DRIVER TRUE |
|
|
|
define HAL_NO_GPIO_IRQ |
|
define CH_CFG_ST_TIMEDELTA 0 |
|
#define CH_CFG_USE_DYNAMIC FALSE |
|
define SERIAL_BUFFERS_SIZE 512 |
|
define PORT_INT_REQUIRED_STACK 64 |
|
|
|
# avoid timer and RCIN threads to save memory |
|
define HAL_NO_TIMER_THREAD |
|
define HAL_NO_RCIN_THREAD |
|
|
|
#defined to turn off undef warnings |
|
define __FPU_PRESENT 0 |
|
|
|
define HAL_USE_RTC FALSE |
|
define DISABLE_SERIAL_ESC_COMM TRUE |
|
define NO_DATAFLASH TRUE |
|
|
|
define DMA_RESERVE_SIZE 0 |
|
|
|
define PERIPH_FW TRUE |
|
|
|
# MAIN_STACK is stack of initial thread |
|
MAIN_STACK 0x100 |
|
|
|
# PROCESS_STACK controls stack for main thread |
|
PROCESS_STACK 0x600 |
|
define HAL_DISABLE_LOOP_DELAY |
|
|
|
# enable CAN support |
|
PA11 CAN_RX CAN |
|
PA12 CAN_TX CAN |
|
define HAL_USE_CAN TRUE |
|
define STM32_CAN_USE_CAN1 TRUE |
|
|
|
# start with a fixed node ID so the board is usable without DNA |
|
define HAL_CAN_DEFAULT_NODE_ID 117 |
|
|
|
define CAN_APP_VERSION_MAJOR 1 |
|
define CAN_APP_VERSION_MINOR 0 |
|
define CAN_APP_NODE_NAME "org.ardupilot.ap_periph" |
|
|
|
define HAL_USE_I2C TRUE |
|
define STM32_I2C_USE_I2C1 TRUE |
|
|
|
define HAL_NO_ROMFS_SUPPORT |
|
|
|
define HAL_UART_MIN_TX_SIZE 256 |
|
define HAL_UART_MIN_RX_SIZE 128 |
|
|
|
define CH_DBG_ENABLE_STACK_CHECK TRUE |
|
|
|
define HAL_UART_STACK_SIZE 256 |
|
define STORAGE_THD_WA_SIZE 512 |
|
|
|
define HAL_NO_GCS |
|
define HAL_NO_LOGGING |
|
define HAL_NO_MONITOR_THREAD |
|
|
|
define HAL_MINIMIZE_FEATURES 0 |
|
|
|
define HAL_BUILD_AP_PERIPH |
|
|
|
# only one I2C bus |
|
I2C_ORDER I2C1 |
|
|
|
COMPASS RM3100 SPI:rm3100 false ROTATION_NONE |
|
|
|
define HAL_I2C_CLEAR_ON_TIMEOUT 0 |
|
|
|
define HAL_DEVICE_THREAD_STACK 768 |
|
|
|
define AP_PARAM_MAX_EMBEDDED_PARAM 0 |
|
|
|
define HAL_PROBE_EXTERNAL_I2C_COMPASSES |
|
define HAL_I2C_INTERNAL_MASK 0 |
|
|
|
# disable dual GPS and GPS blending to save flash space |
|
define GPS_MAX_RECEIVERS 1 |
|
define GPS_MAX_INSTANCES 1 |
|
|
|
# GPS+MAG |
|
define HAL_PERIPH_ENABLE_GPS |
|
define HAL_PERIPH_ENABLE_MAG
|
|
|