zr-v4/ArduPlane/commands.cpp

/*
 *  logic for dealing with the current command in the mission and home location
 */

#include "Plane.h"

/*
 *  set_next_WP - sets the target location the vehicle should fly to
 */
void Plane::set_next_WP(const struct Location &loc)
{
    if (auto_state.next_wp_crosstrack) {
        // copy the current WP into the OldWP slot
        prev_WP_loc = next_WP_loc;
        auto_state.crosstrack = true;
    } else {
        // we should not try to cross-track for this waypoint
        prev_WP_loc = current_loc;
        // use cross-track for the next waypoint
        auto_state.next_wp_crosstrack = true;
        auto_state.crosstrack = false;
    }

    // Load the next_WP slot
    // ---------------------
    next_WP_loc = loc;

    // if lat and lon is zero, then use current lat/lon
    // this allows a mission to contain a "loiter on the spot"
    // command
    if (next_WP_loc.lat == 0 && next_WP_loc.lng == 0) {
        next_WP_loc.lat = current_loc.lat;
        next_WP_loc.lng = current_loc.lng;
        // additionally treat zero altitude as current altitude
        if (next_WP_loc.alt == 0) {
            next_WP_loc.alt = current_loc.alt;
            next_WP_loc.flags.relative_alt = false;
            next_WP_loc.flags.terrain_alt = false;
        }
    }

    // convert relative alt to absolute alt
    if (next_WP_loc.flags.relative_alt) {
        next_WP_loc.flags.relative_alt = false;
        next_WP_loc.alt += home.alt;
    }

    // are we already past the waypoint? This happens when we jump
    // waypoints, and it can cause us to skip a waypoint. If we are
    // past the waypoint when we start on a leg, then use the current
    // location as the previous waypoint, to prevent immediately
    // considering the waypoint complete
    if (location_passed_point(current_loc, prev_WP_loc, next_WP_loc)) {
        gcs().send_text(MAV_SEVERITY_NOTICE, "Resetting previous waypoint");
        prev_WP_loc = current_loc;
    }

    // used to control FBW and limit the rate of climb
    // -----------------------------------------------
    set_target_altitude_location(next_WP_loc);

    // zero out our loiter vals to watch for missed waypoints
    loiter_angle_reset();

    setup_glide_slope();
    setup_turn_angle();

    loiter_angle_reset();
}

void Plane::set_guided_WP(void)
{
    if (aparm.loiter_radius < 0 || guided_WP_loc.flags.loiter_ccw) {
        loiter.direction = -1;
    } else {
        loiter.direction = 1;
    }

    // copy the current location into the OldWP slot
    // ---------------------------------------
    prev_WP_loc = current_loc;

    // Load the next_WP slot
    // ---------------------
    next_WP_loc = guided_WP_loc;

    // used to control FBW and limit the rate of climb
    // -----------------------------------------------
    set_target_altitude_current();

    setup_glide_slope();
    setup_turn_angle();

    // reset loiter start time.
    loiter.start_time_ms = 0;

    // start in non-VTOL mode
    auto_state.vtol_loiter = false;
    
    loiter_angle_reset();
}

// run this at setup on the ground
// -------------------------------
void Plane::init_home()
{
    gcs().send_text(MAV_SEVERITY_INFO, "Init HOME");

    ahrs.set_home(gps.location());
    home_is_set = HOME_SET_NOT_LOCKED;
    Log_Write_Home_And_Origin();
    gcs().send_home(gps.location());

    // Save Home to EEPROM
    mission.write_home_to_storage();

    // Save prev loc
    // -------------
    next_WP_loc = prev_WP_loc = home;
}

/*
  update home location from GPS
  this is called as long as we have 3D lock and the arming switch is
  not pushed
*/
void Plane::update_home()
{
    if ((g2.home_reset_threshold == -1) ||
        ((g2.home_reset_threshold > 0) &&
         (fabsf(barometer.get_altitude()) > g2.home_reset_threshold))) {
        // don't auto-update if we have changed barometer altitude
        // significantly. This allows us to cope with slow baro drift
        // but not re-do home and the baro if we have changed height
        // significantly
        return;
    }
    if (home_is_set == HOME_SET_NOT_LOCKED) {
        Location loc;
        if(ahrs.get_position(loc)) {
            ahrs.set_home(loc);
            Log_Write_Home_And_Origin();
            gcs().send_home(loc);
        }
    }
    barometer.update_calibration();
}

// sets ekf_origin if it has not been set.
//  should only be used when there is no GPS to provide an absolute position
void Plane::set_ekf_origin(const Location& loc)
{
    // check location is valid
    if (!check_latlng(loc)) {
        return;
    }

    // check if EKF origin has already been set
    Location ekf_origin;
    if (ahrs.get_origin(ekf_origin)) {
        return;
    }

    if (!ahrs.set_origin(loc)) {
        return;
    }

    // log ahrs home and ekf origin dataflash
    Log_Write_Home_And_Origin();

    // send ekf origin to GCS
    gcs().send_ekf_origin(loc);
}