You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
93 lines
3.3 KiB
93 lines
3.3 KiB
#include "Copter.h" |
|
|
|
#if MODE_CIRCLE_ENABLED == ENABLED |
|
|
|
/* |
|
* Init and run calls for circle flight mode |
|
*/ |
|
|
|
// circle_init - initialise circle controller flight mode |
|
bool ModeCircle::init(bool ignore_checks) |
|
{ |
|
pilot_yaw_override = false; |
|
|
|
// initialize speeds and accelerations |
|
pos_control->set_max_speed_xy(wp_nav->get_default_speed_xy()); |
|
pos_control->set_max_accel_xy(wp_nav->get_wp_acceleration()); |
|
pos_control->set_max_speed_z(-get_pilot_speed_dn(), g.pilot_speed_up); |
|
pos_control->set_max_accel_z(g.pilot_accel_z); |
|
|
|
// initialise circle controller including setting the circle center based on vehicle speed |
|
copter.circle_nav->init(); |
|
|
|
return true; |
|
} |
|
|
|
// circle_run - runs the circle flight mode |
|
// should be called at 100hz or more |
|
void ModeCircle::run() |
|
{ |
|
// initialize speeds and accelerations |
|
pos_control->set_max_speed_xy(wp_nav->get_default_speed_xy()); |
|
pos_control->set_max_accel_xy(wp_nav->get_wp_acceleration()); |
|
pos_control->set_max_speed_z(-get_pilot_speed_dn(), g.pilot_speed_up); |
|
pos_control->set_max_accel_z(g.pilot_accel_z); |
|
|
|
// get pilot's desired yaw rate (or zero if in radio failsafe) |
|
float target_yaw_rate = get_pilot_desired_yaw_rate(channel_yaw->get_control_in()); |
|
if (!is_zero(target_yaw_rate)) { |
|
pilot_yaw_override = true; |
|
} |
|
|
|
// get pilot desired climb rate (or zero if in radio failsafe) |
|
float target_climb_rate = get_pilot_desired_climb_rate(channel_throttle->get_control_in()); |
|
// adjust climb rate using rangefinder |
|
if (copter.rangefinder_alt_ok()) { |
|
// if rangefinder is ok, use surface tracking |
|
target_climb_rate = copter.get_surface_tracking_climb_rate(target_climb_rate); |
|
} |
|
|
|
// if not armed set throttle to zero and exit immediately |
|
if (is_disarmed_or_landed()) { |
|
make_safe_spool_down(); |
|
return; |
|
} |
|
|
|
// set motors to full range |
|
motors->set_desired_spool_state(AP_Motors::DesiredSpoolState::THROTTLE_UNLIMITED); |
|
|
|
// run circle controller |
|
copter.circle_nav->update(); |
|
|
|
// call attitude controller |
|
if (pilot_yaw_override) { |
|
attitude_control->input_euler_angle_roll_pitch_euler_rate_yaw(copter.circle_nav->get_roll(), |
|
copter.circle_nav->get_pitch(), |
|
target_yaw_rate); |
|
} else { |
|
attitude_control->input_euler_angle_roll_pitch_yaw(copter.circle_nav->get_roll(), |
|
copter.circle_nav->get_pitch(), |
|
copter.circle_nav->get_yaw(), true); |
|
} |
|
|
|
// update altitude target and call position controller |
|
// protects heli's from inflight motor interlock disable |
|
if (motors->get_desired_spool_state() == AP_Motors::DesiredSpoolState::GROUND_IDLE && !copter.ap.land_complete) { |
|
pos_control->set_alt_target_from_climb_rate(-abs(g.land_speed), G_Dt, false); |
|
} else { |
|
pos_control->set_alt_target_from_climb_rate(target_climb_rate, G_Dt, false); |
|
} |
|
pos_control->update_z_controller(); |
|
} |
|
|
|
uint32_t ModeCircle::wp_distance() const |
|
{ |
|
return copter.circle_nav->get_distance_to_target(); |
|
} |
|
|
|
int32_t ModeCircle::wp_bearing() const |
|
{ |
|
return copter.circle_nav->get_bearing_to_target(); |
|
} |
|
|
|
#endif
|
|
|