You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
910 lines
28 KiB
910 lines
28 KiB
/// -*- tab-width: 4; Mode: C++; c-basic-offset: 4; indent-tabs-mode: nil -*- |
|
|
|
#include "Copter.h" |
|
|
|
// start_command - this function will be called when the ap_mission lib wishes to start a new command |
|
bool Copter::start_command(const AP_Mission::Mission_Command& cmd) |
|
{ |
|
// To-Do: logging when new commands start/end |
|
if (should_log(MASK_LOG_CMD)) { |
|
DataFlash.Log_Write_Mission_Cmd(mission, cmd); |
|
} |
|
|
|
switch(cmd.id) { |
|
|
|
/// |
|
/// navigation commands |
|
/// |
|
case MAV_CMD_NAV_TAKEOFF: // 22 |
|
do_takeoff(cmd); |
|
break; |
|
|
|
case MAV_CMD_NAV_WAYPOINT: // 16 Navigate to Waypoint |
|
do_nav_wp(cmd); |
|
break; |
|
|
|
case MAV_CMD_NAV_LAND: // 21 LAND to Waypoint |
|
do_land(cmd); |
|
break; |
|
|
|
case MAV_CMD_NAV_LOITER_UNLIM: // 17 Loiter indefinitely |
|
do_loiter_unlimited(cmd); |
|
break; |
|
|
|
case MAV_CMD_NAV_LOITER_TURNS: //18 Loiter N Times |
|
do_circle(cmd); |
|
break; |
|
|
|
case MAV_CMD_NAV_LOITER_TIME: // 19 |
|
do_loiter_time(cmd); |
|
break; |
|
|
|
case MAV_CMD_NAV_RETURN_TO_LAUNCH: //20 |
|
do_RTL(); |
|
break; |
|
|
|
case MAV_CMD_NAV_SPLINE_WAYPOINT: // 82 Navigate to Waypoint using spline |
|
do_spline_wp(cmd); |
|
break; |
|
|
|
#if NAV_GUIDED == ENABLED |
|
case MAV_CMD_NAV_GUIDED_ENABLE: // 92 accept navigation commands from external nav computer |
|
do_nav_guided_enable(cmd); |
|
break; |
|
#endif |
|
|
|
// |
|
// conditional commands |
|
// |
|
case MAV_CMD_CONDITION_DELAY: // 112 |
|
do_wait_delay(cmd); |
|
break; |
|
|
|
case MAV_CMD_CONDITION_DISTANCE: // 114 |
|
do_within_distance(cmd); |
|
break; |
|
|
|
case MAV_CMD_CONDITION_CHANGE_ALT: // 113 |
|
do_change_alt(cmd); |
|
break; |
|
|
|
case MAV_CMD_CONDITION_YAW: // 115 |
|
do_yaw(cmd); |
|
break; |
|
|
|
/// |
|
/// do commands |
|
/// |
|
case MAV_CMD_DO_CHANGE_SPEED: // 178 |
|
do_change_speed(cmd); |
|
break; |
|
|
|
case MAV_CMD_DO_SET_HOME: // 179 |
|
do_set_home(cmd); |
|
break; |
|
|
|
case MAV_CMD_DO_SET_SERVO: |
|
ServoRelayEvents.do_set_servo(cmd.content.servo.channel, cmd.content.servo.pwm); |
|
break; |
|
|
|
case MAV_CMD_DO_SET_RELAY: |
|
ServoRelayEvents.do_set_relay(cmd.content.relay.num, cmd.content.relay.state); |
|
break; |
|
|
|
case MAV_CMD_DO_REPEAT_SERVO: |
|
ServoRelayEvents.do_repeat_servo(cmd.content.repeat_servo.channel, cmd.content.repeat_servo.pwm, |
|
cmd.content.repeat_servo.repeat_count, cmd.content.repeat_servo.cycle_time * 1000.0f); |
|
break; |
|
|
|
case MAV_CMD_DO_REPEAT_RELAY: |
|
ServoRelayEvents.do_repeat_relay(cmd.content.repeat_relay.num, cmd.content.repeat_relay.repeat_count, |
|
cmd.content.repeat_relay.cycle_time * 1000.0f); |
|
break; |
|
|
|
case MAV_CMD_DO_SET_ROI: // 201 |
|
// point the copter and camera at a region of interest (ROI) |
|
do_roi(cmd); |
|
break; |
|
|
|
case MAV_CMD_DO_MOUNT_CONTROL: // 205 |
|
// point the camera to a specified angle |
|
do_mount_control(cmd); |
|
break; |
|
|
|
#if CAMERA == ENABLED |
|
case MAV_CMD_DO_CONTROL_VIDEO: // Control on-board camera capturing. |Camera ID (-1 for all)| Transmission: 0: disabled, 1: enabled compressed, 2: enabled raw| Transmission mode: 0: video stream, >0: single images every n seconds (decimal)| Recording: 0: disabled, 1: enabled compressed, 2: enabled raw| Empty| Empty| Empty| |
|
break; |
|
|
|
case MAV_CMD_DO_DIGICAM_CONFIGURE: // Mission command to configure an on-board camera controller system. |Modes: P, TV, AV, M, Etc| Shutter speed: Divisor number for one second| Aperture: F stop number| ISO number e.g. 80, 100, 200, Etc| Exposure type enumerator| Command Identity| Main engine cut-off time before camera trigger in seconds/10 (0 means no cut-off)| |
|
do_digicam_configure(cmd); |
|
break; |
|
|
|
case MAV_CMD_DO_DIGICAM_CONTROL: // Mission command to control an on-board camera controller system. |Session control e.g. show/hide lens| Zoom's absolute position| Zooming step value to offset zoom from the current position| Focus Locking, Unlocking or Re-locking| Shooting Command| Command Identity| Empty| |
|
do_digicam_control(cmd); |
|
break; |
|
|
|
case MAV_CMD_DO_SET_CAM_TRIGG_DIST: |
|
camera.set_trigger_distance(cmd.content.cam_trigg_dist.meters); |
|
break; |
|
#endif |
|
|
|
#if PARACHUTE == ENABLED |
|
case MAV_CMD_DO_PARACHUTE: // Mission command to configure or release parachute |
|
do_parachute(cmd); |
|
break; |
|
#endif |
|
|
|
#if EPM_ENABLED == ENABLED |
|
case MAV_CMD_DO_GRIPPER: // Mission command to control EPM gripper |
|
do_gripper(cmd); |
|
break; |
|
#endif |
|
|
|
#if NAV_GUIDED == ENABLED |
|
case MAV_CMD_DO_GUIDED_LIMITS: // 220 accept guided mode limits |
|
do_guided_limits(cmd); |
|
break; |
|
#endif |
|
|
|
default: |
|
// do nothing with unrecognized MAVLink messages |
|
break; |
|
} |
|
|
|
// always return success |
|
return true; |
|
} |
|
|
|
/********************************************************************************/ |
|
// Verify command Handlers |
|
/********************************************************************************/ |
|
|
|
// verify_command_callback - callback function called from ap-mission at 10hz or higher when a command is being run |
|
// we double check that the flight mode is AUTO to avoid the possibility of ap-mission triggering actions while we're not in AUTO mode |
|
bool Copter::verify_command_callback(const AP_Mission::Mission_Command& cmd) |
|
{ |
|
if (control_mode == AUTO) { |
|
bool cmd_complete = verify_command(cmd); |
|
|
|
// send message to GCS |
|
if (cmd_complete) { |
|
gcs_send_mission_item_reached_message(cmd.index); |
|
} |
|
|
|
return cmd_complete; |
|
} |
|
return false; |
|
} |
|
|
|
|
|
// verify_command - this will be called repeatedly by ap_mission lib to ensure the active commands are progressing |
|
// should return true once the active navigation command completes successfully |
|
// called at 10hz or higher |
|
bool Copter::verify_command(const AP_Mission::Mission_Command& cmd) |
|
{ |
|
switch(cmd.id) { |
|
|
|
// |
|
// navigation commands |
|
// |
|
case MAV_CMD_NAV_TAKEOFF: |
|
return verify_takeoff(); |
|
|
|
case MAV_CMD_NAV_WAYPOINT: |
|
return verify_nav_wp(cmd); |
|
|
|
case MAV_CMD_NAV_LAND: |
|
return verify_land(); |
|
|
|
case MAV_CMD_NAV_LOITER_UNLIM: |
|
return verify_loiter_unlimited(); |
|
|
|
case MAV_CMD_NAV_LOITER_TURNS: |
|
return verify_circle(cmd); |
|
|
|
case MAV_CMD_NAV_LOITER_TIME: |
|
return verify_loiter_time(); |
|
|
|
case MAV_CMD_NAV_RETURN_TO_LAUNCH: |
|
return verify_RTL(); |
|
|
|
case MAV_CMD_NAV_SPLINE_WAYPOINT: |
|
return verify_spline_wp(cmd); |
|
|
|
#if NAV_GUIDED == ENABLED |
|
case MAV_CMD_NAV_GUIDED_ENABLE: |
|
return verify_nav_guided_enable(cmd); |
|
#endif |
|
|
|
/// |
|
/// conditional commands |
|
/// |
|
case MAV_CMD_CONDITION_DELAY: |
|
return verify_wait_delay(); |
|
|
|
case MAV_CMD_CONDITION_DISTANCE: |
|
return verify_within_distance(); |
|
|
|
case MAV_CMD_CONDITION_CHANGE_ALT: |
|
return verify_change_alt(); |
|
|
|
case MAV_CMD_CONDITION_YAW: |
|
return verify_yaw(); |
|
|
|
case MAV_CMD_DO_PARACHUTE: |
|
// assume parachute was released successfully |
|
return true; |
|
|
|
default: |
|
// return true if we do not recognize the command so that we move on to the next command |
|
return true; |
|
} |
|
} |
|
|
|
// exit_mission - function that is called once the mission completes |
|
void Copter::exit_mission() |
|
{ |
|
// play a tone |
|
AP_Notify::events.mission_complete = 1; |
|
// if we are not on the ground switch to loiter or land |
|
if(!ap.land_complete) { |
|
// try to enter loiter but if that fails land |
|
if(!auto_loiter_start()) { |
|
set_mode(LAND); |
|
} |
|
}else{ |
|
#if LAND_REQUIRE_MIN_THROTTLE_TO_DISARM == ENABLED |
|
// disarm when the landing detector says we've landed and throttle is at minimum |
|
if (ap.throttle_zero || failsafe.radio) { |
|
init_disarm_motors(); |
|
} |
|
#else |
|
// if we've landed it's safe to disarm |
|
init_disarm_motors(); |
|
#endif |
|
} |
|
} |
|
|
|
/********************************************************************************/ |
|
// |
|
/********************************************************************************/ |
|
|
|
// do_RTL - start Return-to-Launch |
|
void Copter::do_RTL(void) |
|
{ |
|
// start rtl in auto flight mode |
|
auto_rtl_start(); |
|
} |
|
|
|
/********************************************************************************/ |
|
// Nav (Must) commands |
|
/********************************************************************************/ |
|
|
|
// do_takeoff - initiate takeoff navigation command |
|
void Copter::do_takeoff(const AP_Mission::Mission_Command& cmd) |
|
{ |
|
// Set wp navigation target to safe altitude above current position |
|
float takeoff_alt = cmd.content.location.alt; |
|
takeoff_alt = max(takeoff_alt,current_loc.alt); |
|
takeoff_alt = max(takeoff_alt,100.0f); |
|
auto_takeoff_start(takeoff_alt); |
|
} |
|
|
|
// do_nav_wp - initiate move to next waypoint |
|
void Copter::do_nav_wp(const AP_Mission::Mission_Command& cmd) |
|
{ |
|
const Vector3f &curr_pos = inertial_nav.get_position(); |
|
const Vector3f local_pos = pv_location_to_vector_with_default(cmd.content.location, curr_pos); |
|
|
|
// this will be used to remember the time in millis after we reach or pass the WP. |
|
loiter_time = 0; |
|
// this is the delay, stored in seconds |
|
loiter_time_max = abs(cmd.p1); |
|
|
|
// Set wp navigation target |
|
auto_wp_start(local_pos); |
|
// if no delay set the waypoint as "fast" |
|
if (loiter_time_max == 0 ) { |
|
wp_nav.set_fast_waypoint(true); |
|
} |
|
} |
|
|
|
// do_land - initiate landing procedure |
|
void Copter::do_land(const AP_Mission::Mission_Command& cmd) |
|
{ |
|
// To-Do: check if we have already landed |
|
|
|
// if location provided we fly to that location at current altitude |
|
if (cmd.content.location.lat != 0 || cmd.content.location.lng != 0) { |
|
// set state to fly to location |
|
land_state = LAND_STATE_FLY_TO_LOCATION; |
|
|
|
// calculate and set desired location above landing target |
|
Vector3f pos = pv_location_to_vector(cmd.content.location); |
|
pos.z = inertial_nav.get_altitude(); |
|
auto_wp_start(pos); |
|
}else{ |
|
// set landing state |
|
land_state = LAND_STATE_DESCENDING; |
|
|
|
// initialise landing controller |
|
auto_land_start(); |
|
} |
|
} |
|
|
|
// do_loiter_unlimited - start loitering with no end conditions |
|
// note: caller should set yaw_mode |
|
void Copter::do_loiter_unlimited(const AP_Mission::Mission_Command& cmd) |
|
{ |
|
Vector3f target_pos; |
|
|
|
// get current position |
|
Vector3f curr_pos = inertial_nav.get_position(); |
|
|
|
// default to use position provided |
|
target_pos = pv_location_to_vector(cmd.content.location); |
|
|
|
// use current location if not provided |
|
if(cmd.content.location.lat == 0 && cmd.content.location.lng == 0) { |
|
wp_nav.get_wp_stopping_point_xy(target_pos); |
|
} |
|
|
|
// use current altitude if not provided |
|
// To-Do: use z-axis stopping point instead of current alt |
|
if( cmd.content.location.alt == 0 ) { |
|
target_pos.z = curr_pos.z; |
|
} |
|
|
|
// start way point navigator and provide it the desired location |
|
auto_wp_start(target_pos); |
|
} |
|
|
|
// do_circle - initiate moving in a circle |
|
void Copter::do_circle(const AP_Mission::Mission_Command& cmd) |
|
{ |
|
Vector3f curr_pos = inertial_nav.get_position(); |
|
Vector3f circle_center = pv_location_to_vector(cmd.content.location); |
|
uint8_t circle_radius_m = HIGHBYTE(cmd.p1); // circle radius held in high byte of p1 |
|
bool move_to_edge_required = false; |
|
|
|
// set target altitude if not provided |
|
if (cmd.content.location.alt == 0) { |
|
circle_center.z = curr_pos.z; |
|
} else { |
|
move_to_edge_required = true; |
|
} |
|
|
|
// set lat/lon position if not provided |
|
// To-Do: use previous command's destination if it was a straight line or spline waypoint command |
|
if (cmd.content.location.lat == 0 && cmd.content.location.lng == 0) { |
|
circle_center.x = curr_pos.x; |
|
circle_center.y = curr_pos.y; |
|
} else { |
|
move_to_edge_required = true; |
|
} |
|
|
|
// set circle controller's center |
|
circle_nav.set_center(circle_center); |
|
|
|
// set circle radius |
|
if (circle_radius_m != 0) { |
|
circle_nav.set_radius((float)circle_radius_m * 100.0f); |
|
} |
|
|
|
// check if we need to move to edge of circle |
|
if (move_to_edge_required) { |
|
// move to edge of circle (verify_circle) will ensure we begin circling once we reach the edge |
|
auto_circle_movetoedge_start(); |
|
} else { |
|
// start circling |
|
auto_circle_start(); |
|
} |
|
} |
|
|
|
// do_loiter_time - initiate loitering at a point for a given time period |
|
// note: caller should set yaw_mode |
|
void Copter::do_loiter_time(const AP_Mission::Mission_Command& cmd) |
|
{ |
|
Vector3f target_pos; |
|
|
|
// get current position |
|
Vector3f curr_pos = inertial_nav.get_position(); |
|
|
|
// default to use position provided |
|
target_pos = pv_location_to_vector(cmd.content.location); |
|
|
|
// use current location if not provided |
|
if(cmd.content.location.lat == 0 && cmd.content.location.lng == 0) { |
|
wp_nav.get_wp_stopping_point_xy(target_pos); |
|
} |
|
|
|
// use current altitude if not provided |
|
if( cmd.content.location.alt == 0 ) { |
|
target_pos.z = curr_pos.z; |
|
} |
|
|
|
// start way point navigator and provide it the desired location |
|
auto_wp_start(target_pos); |
|
|
|
// setup loiter timer |
|
loiter_time = 0; |
|
loiter_time_max = cmd.p1; // units are (seconds) |
|
} |
|
|
|
// do_spline_wp - initiate move to next waypoint |
|
void Copter::do_spline_wp(const AP_Mission::Mission_Command& cmd) |
|
{ |
|
const Vector3f& curr_pos = inertial_nav.get_position(); |
|
Vector3f local_pos = pv_location_to_vector_with_default(cmd.content.location, curr_pos); |
|
|
|
// this will be used to remember the time in millis after we reach or pass the WP. |
|
loiter_time = 0; |
|
// this is the delay, stored in seconds |
|
loiter_time_max = abs(cmd.p1); |
|
|
|
// determine segment start and end type |
|
bool stopped_at_start = true; |
|
AC_WPNav::spline_segment_end_type seg_end_type = AC_WPNav::SEGMENT_END_STOP; |
|
AP_Mission::Mission_Command temp_cmd; |
|
Vector3f next_destination; // end of next segment |
|
|
|
// if previous command was a wp_nav command with no delay set stopped_at_start to false |
|
// To-Do: move processing of delay into wp-nav controller to allow it to determine the stopped_at_start value itself? |
|
uint16_t prev_cmd_idx = mission.get_prev_nav_cmd_index(); |
|
if (prev_cmd_idx != AP_MISSION_CMD_INDEX_NONE) { |
|
if (mission.read_cmd_from_storage(prev_cmd_idx, temp_cmd)) { |
|
if ((temp_cmd.id == MAV_CMD_NAV_WAYPOINT || temp_cmd.id == MAV_CMD_NAV_SPLINE_WAYPOINT) && temp_cmd.p1 == 0) { |
|
stopped_at_start = false; |
|
} |
|
} |
|
} |
|
|
|
// if there is no delay at the end of this segment get next nav command |
|
if (cmd.p1 == 0 && mission.get_next_nav_cmd(cmd.index+1, temp_cmd)) { |
|
// if the next nav command is a waypoint set end type to spline or straight |
|
if (temp_cmd.id == MAV_CMD_NAV_WAYPOINT) { |
|
seg_end_type = AC_WPNav::SEGMENT_END_STRAIGHT; |
|
next_destination = pv_location_to_vector_with_default(temp_cmd.content.location, local_pos); |
|
}else if (temp_cmd.id == MAV_CMD_NAV_SPLINE_WAYPOINT) { |
|
seg_end_type = AC_WPNav::SEGMENT_END_SPLINE; |
|
next_destination = pv_location_to_vector_with_default(temp_cmd.content.location, local_pos); |
|
} |
|
} |
|
|
|
// set spline navigation target |
|
auto_spline_start(local_pos, stopped_at_start, seg_end_type, next_destination); |
|
} |
|
|
|
#if NAV_GUIDED == ENABLED |
|
// do_nav_guided_enable - initiate accepting commands from external nav computer |
|
void Copter::do_nav_guided_enable(const AP_Mission::Mission_Command& cmd) |
|
{ |
|
if (cmd.p1 > 0) { |
|
// initialise guided limits |
|
guided_limit_init_time_and_pos(); |
|
|
|
// set spline navigation target |
|
auto_nav_guided_start(); |
|
} |
|
} |
|
#endif // NAV_GUIDED |
|
|
|
|
|
#if PARACHUTE == ENABLED |
|
// do_parachute - configure or release parachute |
|
void Copter::do_parachute(const AP_Mission::Mission_Command& cmd) |
|
{ |
|
switch (cmd.p1) { |
|
case PARACHUTE_DISABLE: |
|
parachute.enabled(false); |
|
Log_Write_Event(DATA_PARACHUTE_DISABLED); |
|
break; |
|
case PARACHUTE_ENABLE: |
|
parachute.enabled(true); |
|
Log_Write_Event(DATA_PARACHUTE_ENABLED); |
|
break; |
|
case PARACHUTE_RELEASE: |
|
parachute_release(); |
|
break; |
|
default: |
|
// do nothing |
|
break; |
|
} |
|
} |
|
#endif |
|
|
|
#if EPM_ENABLED == ENABLED |
|
// do_gripper - control EPM gripper |
|
void Copter::do_gripper(const AP_Mission::Mission_Command& cmd) |
|
{ |
|
// Note: we ignore the gripper num parameter because we only support one gripper |
|
switch (cmd.content.gripper.action) { |
|
case GRIPPER_ACTION_RELEASE: |
|
epm.release(); |
|
Log_Write_Event(DATA_EPM_RELEASE); |
|
break; |
|
case GRIPPER_ACTION_GRAB: |
|
epm.grab(); |
|
Log_Write_Event(DATA_EPM_GRAB); |
|
break; |
|
default: |
|
// do nothing |
|
break; |
|
} |
|
} |
|
#endif |
|
|
|
#if NAV_GUIDED == ENABLED |
|
// do_guided_limits - pass guided limits to guided controller |
|
void Copter::do_guided_limits(const AP_Mission::Mission_Command& cmd) |
|
{ |
|
guided_limit_set(cmd.p1 * 1000, // convert seconds to ms |
|
cmd.content.guided_limits.alt_min * 100.0f, // convert meters to cm |
|
cmd.content.guided_limits.alt_max * 100.0f, // convert meters to cm |
|
cmd.content.guided_limits.horiz_max * 100.0f); // convert meters to cm |
|
} |
|
#endif |
|
|
|
/********************************************************************************/ |
|
// Verify Nav (Must) commands |
|
/********************************************************************************/ |
|
|
|
// verify_takeoff - check if we have completed the takeoff |
|
bool Copter::verify_takeoff() |
|
{ |
|
// have we reached our target altitude? |
|
return wp_nav.reached_wp_destination(); |
|
} |
|
|
|
// verify_land - returns true if landing has been completed |
|
bool Copter::verify_land() |
|
{ |
|
bool retval = false; |
|
|
|
switch( land_state ) { |
|
case LAND_STATE_FLY_TO_LOCATION: |
|
// check if we've reached the location |
|
if (wp_nav.reached_wp_destination()) { |
|
// get destination so we can use it for loiter target |
|
Vector3f dest = wp_nav.get_wp_destination(); |
|
|
|
// initialise landing controller |
|
auto_land_start(dest); |
|
|
|
// advance to next state |
|
land_state = LAND_STATE_DESCENDING; |
|
} |
|
break; |
|
|
|
case LAND_STATE_DESCENDING: |
|
// rely on THROTTLE_LAND mode to correctly update landing status |
|
retval = ap.land_complete; |
|
break; |
|
|
|
default: |
|
// this should never happen |
|
// TO-DO: log an error |
|
retval = true; |
|
break; |
|
} |
|
|
|
// true is returned if we've successfully landed |
|
return retval; |
|
} |
|
|
|
// verify_nav_wp - check if we have reached the next way point |
|
bool Copter::verify_nav_wp(const AP_Mission::Mission_Command& cmd) |
|
{ |
|
// check if we have reached the waypoint |
|
if( !wp_nav.reached_wp_destination() ) { |
|
return false; |
|
} |
|
|
|
// play a tone |
|
AP_Notify::events.waypoint_complete = 1; |
|
|
|
// start timer if necessary |
|
if(loiter_time == 0) { |
|
loiter_time = millis(); |
|
} |
|
|
|
// check if timer has run out |
|
if (((millis() - loiter_time) / 1000) >= loiter_time_max) { |
|
gcs_send_text_fmt(MAV_SEVERITY_INFO, "Reached command #%i",cmd.index); |
|
return true; |
|
}else{ |
|
return false; |
|
} |
|
} |
|
|
|
bool Copter::verify_loiter_unlimited() |
|
{ |
|
return false; |
|
} |
|
|
|
// verify_loiter_time - check if we have loitered long enough |
|
bool Copter::verify_loiter_time() |
|
{ |
|
// return immediately if we haven't reached our destination |
|
if (!wp_nav.reached_wp_destination()) { |
|
return false; |
|
} |
|
|
|
// start our loiter timer |
|
if( loiter_time == 0 ) { |
|
loiter_time = millis(); |
|
} |
|
|
|
// check if loiter timer has run out |
|
return (((millis() - loiter_time) / 1000) >= loiter_time_max); |
|
} |
|
|
|
// verify_circle - check if we have circled the point enough |
|
bool Copter::verify_circle(const AP_Mission::Mission_Command& cmd) |
|
{ |
|
// check if we've reached the edge |
|
if (auto_mode == Auto_CircleMoveToEdge) { |
|
if (wp_nav.reached_wp_destination()) { |
|
Vector3f curr_pos = inertial_nav.get_position(); |
|
Vector3f circle_center = pv_location_to_vector(cmd.content.location); |
|
|
|
// set target altitude if not provided |
|
if (is_zero(circle_center.z)) { |
|
circle_center.z = curr_pos.z; |
|
} |
|
|
|
// set lat/lon position if not provided |
|
if (cmd.content.location.lat == 0 && cmd.content.location.lng == 0) { |
|
circle_center.x = curr_pos.x; |
|
circle_center.y = curr_pos.y; |
|
} |
|
|
|
// start circling |
|
auto_circle_start(); |
|
} |
|
return false; |
|
} |
|
|
|
// check if we have completed circling |
|
return fabsf(circle_nav.get_angle_total()/M_2PI_F) >= LOWBYTE(cmd.p1); |
|
} |
|
|
|
// verify_RTL - handles any state changes required to implement RTL |
|
// do_RTL should have been called once first to initialise all variables |
|
// returns true with RTL has completed successfully |
|
bool Copter::verify_RTL() |
|
{ |
|
return (rtl_state_complete && (rtl_state == RTL_FinalDescent || rtl_state == RTL_Land)); |
|
} |
|
|
|
// verify_spline_wp - check if we have reached the next way point using spline |
|
bool Copter::verify_spline_wp(const AP_Mission::Mission_Command& cmd) |
|
{ |
|
// check if we have reached the waypoint |
|
if( !wp_nav.reached_wp_destination() ) { |
|
return false; |
|
} |
|
|
|
// start timer if necessary |
|
if(loiter_time == 0) { |
|
loiter_time = millis(); |
|
} |
|
|
|
// check if timer has run out |
|
if (((millis() - loiter_time) / 1000) >= loiter_time_max) { |
|
gcs_send_text_fmt(MAV_SEVERITY_INFO, "Reached command #%i",cmd.index); |
|
return true; |
|
}else{ |
|
return false; |
|
} |
|
} |
|
|
|
#if NAV_GUIDED == ENABLED |
|
// verify_nav_guided - check if we have breached any limits |
|
bool Copter::verify_nav_guided_enable(const AP_Mission::Mission_Command& cmd) |
|
{ |
|
// if disabling guided mode then immediately return true so we move to next command |
|
if (cmd.p1 == 0) { |
|
return true; |
|
} |
|
|
|
// check time and position limits |
|
return guided_limit_check(); |
|
} |
|
#endif // NAV_GUIDED |
|
|
|
|
|
/********************************************************************************/ |
|
// Condition (May) commands |
|
/********************************************************************************/ |
|
|
|
void Copter::do_wait_delay(const AP_Mission::Mission_Command& cmd) |
|
{ |
|
condition_start = millis(); |
|
condition_value = cmd.content.delay.seconds * 1000; // convert seconds to milliseconds |
|
} |
|
|
|
void Copter::do_change_alt(const AP_Mission::Mission_Command& cmd) |
|
{ |
|
// To-Do: store desired altitude in a variable so that it can be verified later |
|
} |
|
|
|
void Copter::do_within_distance(const AP_Mission::Mission_Command& cmd) |
|
{ |
|
condition_value = cmd.content.distance.meters * 100; |
|
} |
|
|
|
void Copter::do_yaw(const AP_Mission::Mission_Command& cmd) |
|
{ |
|
set_auto_yaw_look_at_heading( |
|
cmd.content.yaw.angle_deg, |
|
cmd.content.yaw.turn_rate_dps, |
|
cmd.content.yaw.direction, |
|
cmd.content.yaw.relative_angle); |
|
} |
|
|
|
|
|
/********************************************************************************/ |
|
// Verify Condition (May) commands |
|
/********************************************************************************/ |
|
|
|
bool Copter::verify_wait_delay() |
|
{ |
|
if (millis() - condition_start > (uint32_t)max(condition_value,0)) { |
|
condition_value = 0; |
|
return true; |
|
} |
|
return false; |
|
} |
|
|
|
bool Copter::verify_change_alt() |
|
{ |
|
// To-Do: use recorded target altitude to verify we have reached the target |
|
return true; |
|
} |
|
|
|
bool Copter::verify_within_distance() |
|
{ |
|
// update distance calculation |
|
calc_wp_distance(); |
|
if (wp_distance < max(condition_value,0)) { |
|
condition_value = 0; |
|
return true; |
|
} |
|
return false; |
|
} |
|
|
|
// verify_yaw - return true if we have reached the desired heading |
|
bool Copter::verify_yaw() |
|
{ |
|
// set yaw mode if it has been changed (the waypoint controller often retakes control of yaw as it executes a new waypoint command) |
|
if (auto_yaw_mode != AUTO_YAW_LOOK_AT_HEADING) { |
|
set_auto_yaw_mode(AUTO_YAW_LOOK_AT_HEADING); |
|
} |
|
|
|
// check if we are within 2 degrees of the target heading |
|
if (labs(wrap_180_cd(ahrs.yaw_sensor-yaw_look_at_heading)) <= 200) { |
|
return true; |
|
}else{ |
|
return false; |
|
} |
|
} |
|
|
|
/********************************************************************************/ |
|
// Do (Now) commands |
|
/********************************************************************************/ |
|
|
|
// do_guided - start guided mode |
|
bool Copter::do_guided(const AP_Mission::Mission_Command& cmd) |
|
{ |
|
Vector3f pos_or_vel; // target location or velocity |
|
|
|
// only process guided waypoint if we are in guided mode |
|
if (control_mode != GUIDED && !(control_mode == AUTO && auto_mode == Auto_NavGuided)) { |
|
return false; |
|
} |
|
|
|
// switch to handle different commands |
|
switch (cmd.id) { |
|
|
|
case MAV_CMD_NAV_WAYPOINT: |
|
// set wp_nav's destination |
|
pos_or_vel = pv_location_to_vector(cmd.content.location); |
|
guided_set_destination(pos_or_vel); |
|
return true; |
|
break; |
|
|
|
case MAV_CMD_CONDITION_YAW: |
|
do_yaw(cmd); |
|
return true; |
|
break; |
|
|
|
default: |
|
// reject unrecognised command |
|
return false; |
|
break; |
|
} |
|
|
|
return true; |
|
} |
|
|
|
void Copter::do_change_speed(const AP_Mission::Mission_Command& cmd) |
|
{ |
|
if (cmd.content.speed.target_ms > 0) { |
|
wp_nav.set_speed_xy(cmd.content.speed.target_ms * 100.0f); |
|
} |
|
} |
|
|
|
void Copter::do_set_home(const AP_Mission::Mission_Command& cmd) |
|
{ |
|
if(cmd.p1 == 1 || (cmd.content.location.lat == 0 && cmd.content.location.lng == 0 && cmd.content.location.alt == 0)) { |
|
set_home_to_current_location(); |
|
} else { |
|
if (!far_from_EKF_origin(cmd.content.location)) { |
|
set_home(cmd.content.location); |
|
} |
|
} |
|
} |
|
|
|
// do_roi - starts actions required by MAV_CMD_NAV_ROI |
|
// this involves either moving the camera to point at the ROI (region of interest) |
|
// and possibly rotating the copter to point at the ROI if our mount type does not support a yaw feature |
|
// TO-DO: add support for other features of MAV_CMD_DO_SET_ROI including pointing at a given waypoint |
|
void Copter::do_roi(const AP_Mission::Mission_Command& cmd) |
|
{ |
|
set_auto_yaw_roi(cmd.content.location); |
|
} |
|
|
|
// do_digicam_configure Send Digicam Configure message with the camera library |
|
void Copter::do_digicam_configure(const AP_Mission::Mission_Command& cmd) |
|
{ |
|
#if CAMERA == ENABLED |
|
camera.configure(cmd.content.digicam_configure.shooting_mode, |
|
cmd.content.digicam_configure.shutter_speed, |
|
cmd.content.digicam_configure.aperture, |
|
cmd.content.digicam_configure.ISO, |
|
cmd.content.digicam_configure.exposure_type, |
|
cmd.content.digicam_configure.cmd_id, |
|
cmd.content.digicam_configure.engine_cutoff_time); |
|
#endif |
|
} |
|
|
|
// do_digicam_control Send Digicam Control message with the camera library |
|
void Copter::do_digicam_control(const AP_Mission::Mission_Command& cmd) |
|
{ |
|
#if CAMERA == ENABLED |
|
camera.control(cmd.content.digicam_control.session, |
|
cmd.content.digicam_control.zoom_pos, |
|
cmd.content.digicam_control.zoom_step, |
|
cmd.content.digicam_control.focus_lock, |
|
cmd.content.digicam_control.shooting_cmd, |
|
cmd.content.digicam_control.cmd_id); |
|
log_picture(); |
|
#endif |
|
} |
|
|
|
// do_take_picture - take a picture with the camera library |
|
void Copter::do_take_picture() |
|
{ |
|
#if CAMERA == ENABLED |
|
camera.trigger_pic(true); |
|
log_picture(); |
|
#endif |
|
} |
|
|
|
// log_picture - log picture taken and send feedback to GCS |
|
void Copter::log_picture() |
|
{ |
|
gcs_send_message(MSG_CAMERA_FEEDBACK); |
|
if (should_log(MASK_LOG_CAMERA)) { |
|
DataFlash.Log_Write_Camera(ahrs, gps, current_loc); |
|
} |
|
} |
|
|
|
// point the camera to a specified angle |
|
void Copter::do_mount_control(const AP_Mission::Mission_Command& cmd) |
|
{ |
|
#if MOUNT == ENABLED |
|
camera_mount.set_angle_targets(cmd.content.mount_control.roll, cmd.content.mount_control.pitch, cmd.content.mount_control.yaw); |
|
#endif |
|
}
|
|
|